“Dobinsons GS59-713 Pair of Rear Shocks | Toyota Sequoia 2008-2022” has been added to your cart. Continue shopping
You may be interested in…
-
SuspensionFREE SHIPPING
within 48 US StatesDobinsons IMS59-60713 2.6″ IFP Rear Shocks Pair | Toyota Sequoia 2008-2022
- Suits 2008-2022 Toyota Sequoia without rear air suspension, for lift heights between 0″ and 2.5″
- SOLD IN PAIRS
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment – Suitable for most heavier vehicles
- Full 2 year limited warranty, no set rebuild time period
- 343mm compressed length, 489mm extended length (these are extended travel over the GS59-713 shocks)
- Note: the video shows an IMS front strut that takes a coil. This listing is for the rear IMS shock, no adjustability.
(14 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons MRA59-A711 3-Way Adjustable MRA Rear Shocks Pair | Tundra 2007-2021
- 3-way adjustable valving – Adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
(16 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.5 Tundra DCA Remote Resi Coilovers | 2007-2021
- Suits Toyota Tundra 2007-2021 2WD and 4WD
- Comes preset to 2.5″ of lift
- Dual Compression Adjuster (DCA) is on the resi to fine tune the ride quality
- Dual Compression Adjusters with 10 adjustments for each knob
- Increased suspension travel
- Specific valving for each vehicle providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Remote reservoir equipped with dual compression adjusters allowing for high-speed and low-speed compression adjustments
- Less seal drag with the 3/4″ shafts compared to traditional 7/8″ shafts resulting in smoother operation
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Cold wound, high-tensile alloy steel coil springs that retain consistent rate and ride height
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2.5″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 3/4″ shafts
- Provides up to 3” of lift | Must be paired with aftermarket UCA
- Note: We do not recommend lifting the vehicle more than 3″. Excessive preload will reduce the ride quality
- What’s Included:
- 2.5 DCA coilover shocks with remote reservoirs Pair
- Coils installed are 16” long, 700 LBF/in Spring Rate
- Sway bar relocation mounts with reservoir brackets
- Spanner wrench
- All necessary mounting hardware
- Installation instructions
- Installation video is down below
- Matching Rear Shocks
(4 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons MRA59-A940 3-Way Adjustable MRA Rear Shocks Pair
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you
- 10 Stage High Speed Compression – For aggressive, high speed offroading through ruts and holes
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm (2.2″) O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMITM CNC machined components for precise tolerances
- Parker Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir, Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg, CNC TIG Precision Welded Body End Mounts
- EDP Surface Protection, Direct Bolt-On Design
- Fully Rebuildable Design, Full 2 year limited warranty, no set rebuild time period
- 14.2″ compressed length, 24.2″ extended length
- Installation Instructions
- Works with factory brake line length and OE bump stop length, no extensions required
- Includes reservoir brackets and hardware
- SOLD IN PAIRS
(16 reviews) -
Sequoia 2nd Gen (2008-2022)FREE SHIPPING
within 48 US StatesDobinsons MRA59-A713 3-Way Adjustable Rear Shocks Pair | Sequoia 2008-2022
- Suits Toyota Sequoia 2008-2022
- 3-way adjustable valving – Adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
(13 reviews) -
Brake LinesFREE SHIPPING
within 48 US StatesExtended Rear Brake Lines +4″ for Toyota Tacoma 2005-2023 (Black)
- American made D.O.T. Certified extruded teflon core, stainless steel braided and coated with a PVC cover
- 4″ longer than stock for long travel suspension lifts
- Suits the following vehicles: Toyota Tacoma 2005-2015, Toyota Tacoma 2016+
- Can be used with any lift height, however these are extra long for long travel rear shocks
- Sold as a pair with new retaining clips
- This set is BLACK in color
(26 reviews)
Cart totals
| Subtotal | $2,457.00 |
|---|---|
| Shipping |
Shipping to FL. |
| Route Shipping Protection | $61.43 |
| Tax | $184.28 |
| Total | $2,702.71 |
