Your cart is currently empty!
Tacoma 1st Gen (1996-2004)
Showing 1–30 of 41 results
-
Full Suspension Kits - Tacoma 1st Gen (6)
-
Skid Plates - Tacoma 1st Gen (4)
-
4Runner 3rd Gen (1996-2002)
Dobinsons PS59-4030 1/2″ Lift Alloy Strut Top Mount Spacer | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits various vehicles, as listed below
- Dobinsons PS59-4030 1/4″ spacer at the strut equals approximately 1/2″ lift at the wheel
- Designed to exact OE top mount specs
- T-6061 aircraft grade alloy, machined then black anodized for corrosion resistance
- Allows quick method of correcting a vehicle lean without complete strut disassembly
- Sold individually
- Fits between the strut top mount and the chassis of the vehicle
- Note: See 2nd photo to make sure you have enough threads left to install the spacer. This vehicle came with short studs that don’t allow the spacer to be installed without changing out to thicker studs
$55.00 Add to cart -
DobinsonsShips FREE !!
within 48 US StatesDobinsons IMS59-50222 Extended Travel Front IMS Struts | Tacoma 4Runner Tundra Sequoia
- Suits 1996-2002 3rd Gen 4Runner, 1996-2004 1st Gen Tacoma, 2000-2006 Toyota Tundra, 2001-2007 Toyota Sequoia, Toyota Prado 90
- Extended Travel
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
- Struts only, sold as a pair – the coils are sold separately
- 473mm extended, 335mm compressed lengths
- It’s recommended that these coilovers to be run with aftermarket UCA’s for coilover clearance and correct travel
$650.00 Add to cart -
4Runner 3rd Gen (1996-2002)
Dobinsons SC59-002 Pair of Strut Top Plates | Tacoma 98-04 + 4Runner 96-02
- Suits Toyota Tacoma 1st Gen 1998-2004, 4Runner 3rd Gen 1996 to 2002, and Toyota Land Cruiser Prado 90
- Designed to exact OE specs, using all new rubber bushes, washers and seats
- New zinc coated hardware for corrosion resistance
- Allows faster assembly of new components, not needing to disassemble used parts
- Enough for 1 vehicle, sold as pairs
- Photo is of actual product and parts included
- Nut size – M10 x 1.25 nylock – easy to find locally to you if you lose or damage one
- Assembly Instructions
$120.00 Add to cart -
4Runner 3rd Gen (1996-2002)
Dobinsons GS59-222 Struts for 4Runner 96-02 Tacoma 98-04 Sequoia 01-07 Tundra 00-06
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals, Fuchs German shock absorber oil, Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- Matched to compliment Dobinsons Complete Suspension Systems
- 465mm extended, 335mm compressed
- Sold in Pairs
$350.00 Add to cart -
Coil Springs
Dobinsons C59-276 Front Lifted Coil Springs for Toyota 4×4 Trucks and SUV’s
- 3rd Gen 4Runner 4×4 (1996-2002) – Lifts 2″ on a stock to medium load front end
- Toyota Tacoma 4×4 1998 to 2004 – 1.5″ with stock weight
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- 362mm free height, 586LBF/in spring rate
- Sold in Pairs
$270.00 Select options -
Suspension
Dobinsons GS59-649 Rear Twin Tube Shocks – Comfort Option
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals, Fuchs German shock absorber oil, Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- Matched to compliment Dobinsons Complete Suspension Systems
- GS59-649 is a comfort version (softer) of the GS59-651
- See full vehicle list below for fitment
- 591mm extended, 363mm compressed, 51mm body diameter
$310.00 Add to cart -
DobinsonsShips FREE !!
within 48 US StatesDobinsons IMS59-50649 Monotube IFP Rear Shocks
- Fully rebuildable and re-valvable
- SOLD IN PAIRS
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- 614mm extended, 409mm compressed
$580.00 Add to cart -
Suspension
Dobinsons C59-134 Front Lifted Coil Springs for Toyota 4×4 Trucks and SUV’s
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
- 370mm free height, 17mm wire thickness, 586LBF/in spring rate
$270.00 Select options -
Suspension
Dobinsons 2″ Rear Lift Blocks – Quick Ride Kit – Tacoma Tundra Hilux Frontier
- High Quality cast steel lift blocks/spacers, painted black
- Extended length u-bolts, zinc coated
- Fast and simple to install
- New extended length rear shocks are recommended
- Only to be used with OE height leaf springs
- Suits all Toyota Tacoma’s from 1998 to 2023 and Tundra’s from 2000 to 2021
- Suits all Toyota Hilux from 2005 to 2023
- Suits all Nissan Frontier D21, D22, D40, D41 from 1985 to 2022+
- Installation Instructions
$165.00 Add to cart -
Replacement Bushings
Dobinsons Lower Strut Bushing – For -222 -220 -221 -782 -470
- Dobinsons replacement lower strut bushing
- Suits a variety of Dobinsons struts/shocks, part numbers ending in -222 -220 -221 -782 -470
- Full list of part numbers this fits is below
- This is for a single bushing only for 1 strut or shock
- High quality natural rubber bushing
- Photo for illustration purposes of the bushing type
$20.00 Add to cart -
Add-a-Leaf
Wheeler’s 3 Leaf Progressive Add-A-Leaf Set – 1.5″ Lift for 95-03 Tacoma 99-06 Tundra
- Suits 1995-2004 and 2005-2023 Toyota Tacoma 4×4 and Pre-Runner, and 1999-2006 Toyota Tundra
- Includes 2 x Progressive add-a-leaf sets (3 leaves each), 2 longer center pins and replacement longer U-bolts
- Adds 1.5″ of lift approximately. Different bed/cab configurations could see variations in lift height
- Added constant load on the rear of the truck may reduce the total added lift height, but this will support additional weight better than the stock leaf pack
- Feature 60mm diamond cut ends and anti-friction pads for smooth, squeak free performance
- On some years and/or models, you may need to remove the front clamp from the Add-A-Leaf to avoid interference with the overload spring and gas tank strap
- Instructions
$208.00 Add to cart -
Suspension
Dobinsons 30mm (1.2″) Rear Lift Blocks – Quick Ride Kit – Tacoma Tundra Hilux Frontier
- High Quality cast steel lift blocks/spacers, painted black
- Extended length u-bolts, zinc coated
- Fast and simple to install
- New extended length rear shocks are recommended
- Only designed to be used with OE height leaf springs
- Built-in correction for pinion angle
- Full vehicle range is listed down below
- Installation Instructions
$165.00 Add to cart -
Trail-Gear
TG Diff Drop Kit – 95-04 Tacoma 96-02 4Runner 00-06 Tundra
- Solid aircraft-grade 6061-T6 aluminum spacers
- Zinc-plated Grade 8 hardware
- Aluminum spacers and longer zinc-plated Class 8.8 bolts to move the stock skid plate down
- Fits the following applications:
- Toyota Tacoma 1995-2004 (4×4)
- Toyota Tundra 2000-2006 (4×4)
- Toyota 4Runner 1996-2002 (4×4)
- Toyota Sequoia 2000-2006 (4×4)
- Made in USA
$57.00 Add to cart -
DobinsonsShips FREE !!
within 48 US StatesDobinsons MRA59-A222 3-Way Adjustable MRA Front Struts
- Suits 2001-2007 Toyota Sequoia 4×4, 1998-2004 Toyota Tacoma 4×4, 2000-2006 Toyota Tundra 4×4, 1996-2002 Toyota 4Runner 4×4
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- 458mm extended length, 335mm compressed
- Includes Universal Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Does not include coil springs or top mounts – sold separately
- Instructions for setting coil seat height
$1,280.00 Add to cart -
SuspensionShips FREE !!
within 48 US StatesDobinsons MRA59-A649 3-Way Adjustable Rear Shocks for Toyota
- Suits various vehicles, list is down below
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your springs, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Piggyback Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- 626mm extended, 400mm compressed
- Full 2 year limited warranty, no set rebuild time period
$1,150.00 Add to cart -
SPCShips FREE !!
within 48 US StatesSPC 25460 | UCA’s for Tacoma 98-04 & 4Runner 96-02
- Improved clearance to get around the spring bucket
- 80° of articulation in its ball joint
- SPC’s arm gives you maximum droop travel.
- SPC’s arms have +2° of caster built into them
- Arm will get you 0° to +4° of caster and ±2° of camber
- Maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming
- Installation Instructions
$849.96 Add to cart -
Tacoma 1st Gen (1996-2004)
Dobinsons 2-2.5″ Pre-Assembled IMS Tacoma Coilovers for 1998-2004
- Suits 1998-2004 Toyota Tacoma 4×4 Models
- Looking for a quick and easy way to lift your Tacoma? This is your answer
- Extended Travel IMS59-50222 Coilovers – 473mm extended, 335mm compressed lengths
- Dobinsons IMS are height adjustable by a fully threaded body
- The Dobinsons IMS Coilovers will come pre-assembled with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
- Instructions for setting coil seat height
- It’s recommended that these coilovers to be run with aftermarket UCA’s for coilover clearance and correct travel
- Link to Matching rear shocks, regular travel, or long travel
$1,165.00 Select options -
Tacoma 1st Gen (1996-2004)Ships FREE !!
within 48 US StatesDobinsons 2-2.5″ Pre-Assembled MRA Tacoma Coilovers for 1998-2004
- Suits 1998-2004 Toyota Tacoma 4×4 Models
- Looking for a quick and easy way to lift your Tacoma? This is your answer
- Extended Travel MRA59-A222 Coilovers – 458mm extended, 335mm compressed lengths
- Dobinsons MRA are height adjustable by a fully threaded body
- The Dobinsons MRA Coilovers will come pre-assembled with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- SOLD IN PAIRS – READY TO BOLT IN
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Includes Universal Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
- Instructions for setting coil seat height
- It’s recommended that these coilovers to be run with aftermarket UCA’s for coilover clearance and correct travel
- Link to Matching rear shocks
$1,795.00 Select options -
Bump Stops
Wheeler’s Rear Superbumps for 95+ Tacoma and 99-06 Tundra
- Suits the following vehicles: 1995-2023 Tacoma and 1999-2006 Toyota Tundra
- Bolts in easily and quickly to replace the firm factory bump stops
- Includes necessary bump stops (2), goes under the factory u-bolts
- Made of a super durable micro-cellular polyurethane formula
- Provides controlled, progressive and comfortable bottoming response from your front suspension
- Installation Instructions
$221.00 Add to cart -
Tacoma 1st Gen (1996-2004)
Dobinsons 2.0″ IMS Lift Kit Toyota Tacoma 1998 to 2004 with Blocks or AAL
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Fully re-buildable and re-valvable shocks
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston 50mm bore – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Includes 2 Front IMS Struts, 2 Rear IMS Shocks, 2 Front Coil Springs (a pair), Rear Spacer Blocks and U-Bolts
- It’s recommended that these coilovers to be run with aftermarket UCA’s for coilover clearance and correct travel
From $1,500.00 Select options -
DobinsonsShips FREE !!
within 48 US StatesDobinsons IMS59-50229 Monotube IFP Rear Shocks
- Suits the rear of Toyota Hilux Revo 2016+ and Toyota Tacoma 1998-2004 (for long travel)
- For the Tacoma, these are considered long travel shocks for maximum droop. Additional parts may be required to get that travel out of the truck, such as bump stop extensions, longer brake lines, etc
- Fully rebuildable and re-valvable
- SOLD IN PAIRS
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Dobinsons IMS59-50229 Specifications: 650mm extended, 416mm compressed, 56mm body size
$580.00 Add to cart -
Tacoma 1st Gen (1996-2004)
Dobinsons 1.5″ to 2.0″ Front Coils for Toyota Tacoma 1998 to 2004
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Coil springs are sold as a pair, powder coated teal
- C59-276 – 1.5″ with stock weight
- C59-134 – 1.5″ with bumper and winch
- C59-134 – 2.0″ with stock weight
From $270.00 Select options -
Tacoma 1st Gen (1996-2004)
Dobinsons 2.0″ Lift Kit Toyota Tacoma 1998 to 2004 with Blocks or AAL
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Includes 2 Front Struts, 2 Rear Shocks, 2 Front Coil Springs (a pair), Rear Spacer Blocks and U-Bolts
- Option now to use Wheeler’s add-a-leaf kit instead of blocks if you’d prefer
- It’s recommended that these coilovers to be run with aftermarket UCA’s for coilover clearance and correct travel
From $930.00 Select options -
Accessories
Dobinsons Pickup Rear Drawers Kit with Fridge Slide Universal Fit
- 1.6mm Zinc Plated Robust Steel Construction
- 12mm Heavy Duty Plywood Panels with Marine Carpet Covering
- Built in Heavy Duty Fridge Slide
- 8 x Heavy Duty Stainless Steel Tie Down Points
- Requires tonneau cover or canopy
- Universal Mount, measures 51.1 x 39.4 x 10 inches (L, W, H), requires drilling of truck bed, and custom fitting of side panels (if ordered)
- You can add a universal side wing panel kit down below, so that you can build out the edges of the drawers to the side of your bed
- Aluminum Edging Protection
- Heavy duty lockable latches
- Marine Carpet
- Massive 150KG (330LB) Drawer Capacity on Heavy Duty Roller Bearing System
- Ships to the nearest freight terminal for pickup, unless home delivery is option is added below. We will be in touch to let you know the terminal location
From $1,845.00 Select options -
4Runner 3rd Gen (1996-2002)RCI is on Sale For Spring!!
RCI Engine Skid Plate | 96-02 4Runner 95-04 Tacoma
- Suits 3RD Gen 4Runner and 1995-2004 Tacoma Dual Cab (won’t fit regular cab)
- Protects front two cross-members, low hanging front differential, radiator, and oil pan
- Service openings for easy service and oil changes without removal
- Reinforced edges between cross-members for maximum strength and rigidity
- Bolt protector rings surround exposed bolts, shielding against physical damage
- Smooth, flat surface that easily slides over obstacles
- Black powder coat available for rust resistant, durable and high quality finish
- Installs in minutes
- All hardware and installation instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- Made in the USA.
Original price was: $324.00.$291.60Current price is: $291.60. Add to cart -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD129 Rear Air Locker Toyota 8.4″ 30 Spline
- For Use only with Toyota 8.4″ 12 Bolt 30 spline Rear Axle
- Suits multiple vehicles, the full list is down below. Used in older Tacoma, Sequoia, Tundra and T100 Trucks.
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Add to cart -
Add-a-Leaf
Wheeler’s 1.5″ Lift Add-A-Leaf Set for 1996-2004 Tacoma
- Suits 1996 to 2004 Tacoma 4×4 and Pre-Runner
- Includes 2 single add-a-leafs and 2 longer center pins
- Works with factory length u-bolts or aftermarket
- Adds 1.5″ of lift approximately on dual cab short bed models. Single or Access cab models may see different lift heights
- Added constant load on the rear of the truck may reduce the total added lift height, but this will support additional weight better than the stock leaf pack
- Feature diamond cut ends and anti-friction pads for smooth, squeak free performance
- Instructions
$125.00 Add to cart