“Firestone 4108 Coil-Rite Rear Helper Airbags for 2-3″ Lift | 4Runner FJ Cruiser GX470 GX460” has been added to your cart. Continue shopping
You may be interested in…
-
FirestoneFREE SHIPPING
within 48 US StatesFirestone 2900 Air Command Air Compressor System
- Individual Air Accessory Components Are Also Available, Including Compressors, Air Tanks, And Mounting Solutions, Providing A Wide Variety Of Air Control Assist Solutions
- Adjust The Ride For Various Load And Road Conditions With A Switch, Remote Or Mobile App
- Provides An Instant Air Source For The Air Helper Springs Or Accessories
- Single Point Fill (Both Air Springs Fill To The Same Pressure)
- Light Duty Compressor Specs (100 Pounds Per Square Inch Max Air Pressure, 9 Percent Duty Cycle, 0.32 CFM)
- Electric analog gauge and a single toggle switch (includes housing for easy installation).
- Plug and play wiring harness.
- 30ft of 1/4″ tubing. All required hardware for installation.
- No-Drill Mounting Plate
- Limited 2 Year Warranty
- Dash Panel Style: Controls Two Air Springs Simultaneously
- Type: Heavy Duty
- Maximum Pressure (PSI): 100 Pounds Per Square Inch
- Operation Type: Switch Operated
- Estimated Install Time (Hours): 2
- Installation Manual
(0 reviews) -
TimbrenFREE SHIPPING
within 48 US StatesTimbren Bump Stops Front & Rear | Land Cruiser 80 Series 1990-1997
- Suits 1990-1997 Land Cruiser 80 Series and Lexus LX450
- Includes both Front and Rear bump stops for the whole vehicle
- Active Off-Road Bumpstops provide off-road enthusiasts greater control over their vehicles’ suspension travel. Using progressive-rate springs means that instead of a hard stop at the end of axle travel the axle energy will be absorbed when bottoming-out producing smooth, predictable, and quiet axle engagement and disengagement.
- Unlike OEM bump stops, Active Off-Road Bumpstops are made from natural rubber. Just like our Timbren SES line, Active Off-Road Bumpstops carry a lifetime warranty and a satisfaction guarantee.
- ABSTORLC1 replaces the rear OEM bump stops and ABSTOFLC1A replaces the fronts on the Land Cruiser 80 Series. Upgrade to Active Off-road Bumpstops and experience the difference.
- Maintain Full Axle Travel
- Smooth Axle Engagement and Disengagement
- Enhance Suspension Performance
- Progressive Spring Rate
- Absorbs Energy and Cushions Road Shocks
- Stronger Than OEM Bumpstops
- Easy Installation
- Satisfaction Guarantee
- Lifetime Warranty
- Clearancing of the rear brackets and the bump stop cups may be required on some long travel setups to avoid clearance issues with the coil springs
- Front Instructions and Rear Instructions
(11 reviews) -
Tundra 3rd Gen (2022-2025+)FREE SHIPPING
within 48 US StatesDobinsons Adjustable Rear Upper Trailing Arms Pair | WA59-571K
- Suits Toyota Tundra 2022-2025+, Sequoia 2023-2025+, Land Cruiser 250 Series 2024-2025+, and Tacoma 2024-2025+ and Lexus GX550 2024+
- Fully adjustable to properly set the length and pinion angle
-
On car adjustable with a left hand threaded side (Silver Nut) and a right hand threaded side (Gold Nut)
- Comes installed with high quality rubber OE style bushings for maximum flexibility and longevity
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Oversized adjusters and rod thickness for maximum strength and durability with nut locking feature
- Zinc plated, then powder coated black, for the ultimate finish and protection
- **Not suitable for vehicles with rear height sensors (attached to OEM arms)
- Trailing arms DO NOT have headlight adjustment bracket
- Instructions written down below in the description
(4 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons MRA59-A687 3-Way Adjustable MRA Rear Shocks Pair | 80 Series 4″ Lift
- Suits Toyota Land Cruiser 80 Series and Lexus LX450 1990-97, suitable for 4-5″ of lift, or when used in a long travel setup
- 3-way adjustable valving – Adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 22mm / 7/8″ shaft diameter
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Piggyback Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- 674mm extended, 420mm compressed
- Installation Instructions of the MRA Shocks
- Bump stop extensions and longer brake lines must be run with these longer shocks
(16 reviews) -
Tundra 3rd Gen (2022-2025+)FREE SHIPPING
within 48 US StatesDobinsons Adjustable Rear Lower Control Arms Pair for Tundra + Tacoma
- Suits all 2022-2025+ Toyota Tundra and 2024-2025+ Toyota Tacoma
- Comes with high quality rubber OE style bushings installed for maximum flexibility, and zero noise
- Made from HSLA (High Strength Low Alloy) Steel
- 40mm OD and 6mm wall thickness with support brace
- Oversized adjusters and rod thickness for maximum strength and durability with double-nut locking feature
- Zinc plated, then E-coated black, for the ultimate finish and protection
- Sold as a pair
(4 reviews) -
Dobinsons
Dobinsons SC59-002 Pair of Strut Top Plates
- Suits Toyota Tacoma 1st Gen 1998-2004, 4Runner 3rd Gen 1996 to 2002, and Toyota Land Cruiser Prado 90 and 95 Models RZJ90, VZJ90, KZJ90, KDJ90, RZJ95, VZJ95, KZJ95, KDJ95
- Also suits 2012-2024 Isuzu D-Max and 2020+ Mazda BT-50
- Designed to exact OE specs, using all new rubber bushes, washers and seats
- New zinc coated hardware for corrosion resistance
- Allows faster assembly of new components, not needing to disassemble used parts
- Enough for 1 vehicle, sold as pairs
- Photo is of actual product and parts included
- Nut size – M10 x 1.25 nylock – easy to find locally to you if you lose or damage one
- Assembly Instructions
(9 reviews) -
Shocks + Struts - 3rd Gen 4RunnerFREE SHIPPING
within 48 US StatesDobinsons MRA59-A225 3-Way Adjustable Rear Shocks Pair | 3rd Gen 4Runner 1996-2002
- Suits 3rd Gen Toyota 4Runner 1996-2002
-
Suits Toyota Land Cruiser Prado 90 and 95 Models RZJ90, VZJ90, KZJ90, KDJ90, RZJ95, VZJ95, KZJ95, KDJ95
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your springs, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- 530mm extended length, 344 compressed
- SOLD IN PAIRS
- Includes Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
(15 reviews) -
Tundra 2nd Gen (2007-2021)FREE SHIPPING
within 48 US StatesDobinsons MRA59-A710 3-Way Adjustable MRA Front Struts Pair | Tundra + Sequoia
- Suits 2007-2021 Toyota Tundra and 2008-2022 Toyota Sequoia
- Pair of Struts only, no coils included and not preassembled
- If you’re looking for an assembled set of coilovers, those are here: Assembled Coilovers for 2007-2021 Tundra
- 625mm extended length, 450mm compressed length
- Height adjustable with a fully threaded body
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Requires lower mount clearancing to fit the larger lower leg of the new coilover (see attached photo)
- See attached photo for correct hose routing, can vary depending on UCA’s used
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Reservoir Brackets and Hardware and Sticker Pack
- SOLD IN PAIRS
- Full 2 year limited warranty, no set rebuild time period
- Does not include coil springs – sold separately
- Front coilover assembly instructions
- New UCA’s are required for proper coilover and hose clearance, see all options
- Aftermarket wheels with +18 Offset or less REQUIRED to avoid reservoir + hose rubbing at full lock
- Link to recommended 16″ coils with a 3″ inner diameter and 650LB Spring Rate
- Link to add assembly labor charge, so that when you buy these struts and the coils, you can have them preassembled before shipping
(12 reviews) -
Brake LinesFREE SHIPPING
within 48 US StatesExtended Rear Brake Lines for 4Runner FJ GX470 GX460 2003-2024
- American made D.O.T. Certified extruded teflon core, stainless steel braided and coated with a PVC cover
- 20″ long, works with long travel rear suspension setups
- Suits up to 4″ of lift with long travel shocks or not
- Suits the following vehicles: Toyota 4Runner 4th Gen 2003-2009, Toyota 4Runner 5th Gen 2010-2024, Toyota FJ Cruiser all years, Lexus GX470 all years, Lexus GX460 all years
- Not recommended for stock or un-lifted vehicles, as the brake lines are much longer than necessary
- Sold as a pair with new retaining clips
(19 reviews) -
Dobinsons
Dobinsons Pair of Strut Top Plates for Toyota Tundra 07-21 Sequoia 08-22
- Made specifically for the 4×4 Toyota Tundra from 2007-2021 and Toyota Sequoia from 2008 to 2022
- Designed to exact OE specs, using all new rubber bushes, washers and seats
- New zinc coated hardware for corrosion resistance
- Allows faster assembly of new components, not needing to disassemble used parts
- Enough for 1 vehicle, sold in pairs
- Photo for illustration purposes
(7 reviews) -
100 Series Land Cruiser IFS (1998-2007)FREE SHIPPING
within 48 US StatesDobinsons Tubular UCA Pair | Land Cruiser 100 + Lexus LX470 1998-2007
- For Toyota Land Cruiser 100 Series and Lexus LX470 1998-2007 models
- Not compatible with AHC, it does not have the bracket in place
- Complete kit for both left and right hand side, includes new 555 ball joints installed, OE style rubber frame bushings installed, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Has more clearance around the ball joint than factory UCA’s for better tire clearance
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Product Video
- Also sold without ball joints
- Replacement Ball Joints can be ordered here
(10 reviews) -
Explorer U502 AWD 2012+
Dobinsons C19-438 2″ Lift Front coils for Ford Explorer U502 2012-21 AWD 3.5L 3.7L – Pair
- 2″ front lift coils for a Ford Explorer AWD 3.5L and 3.7L from 2012-2021
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold as a Pair
(5 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons IMS59-60786 Front Ext Travel 2.6″ IFP Shocks Pair | Land Cruiser 100 Series (2-2.5″ lift)
- Suits Toyota Land Cruiser 100 Series and Lexus LX470 Front End
- Requires full diff drop kit and UCA’s before installation
- Front shocks only. To order full kit, click here
- SOLD IN PAIRS
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment – Suitable for most heavier vehicles
- Full 2 year limited warranty, no set rebuild time period
- 470mm extended and 315mm compressed
(17 reviews) -
All Pro OffroadFREE SHIPPING
within 48 US StatesAll Pro 2014-2024 4Runner LoPro Front Bumper Side Supports
- Side supports are only compatible with All Pro 2014+ 4Runner Low Profile Front Bumper
- BUILT 100% IN THE USA
- 3/16″ steel construction
- Zinc plated hardware
- No Drilling or welding required
- Cutting the plastic bumper is required to install side supports
- Comes in Black Powder Coat ready to install
- Weighs 25lbs
- NOTE: Not compatible with Limited Edition 4Runners
- Installation Instructions
(3 reviews) -
ExceptionsFREE SHIPPING
within 48 US StatesDobinsons Adjustable Rear Sway Bar End Link Kit | 4Runner FJ Cruiser GX470 GX460
- Suits 4th and 5th Gen 4Runner 2003-2024, FJ Cruiser (all years), GX470, GX460 (without KDSS)
- Order 1 for 1 vehicle
- Heavy Duty, zinc plated, with high quality ball joint ends for long life
- Kit includes 2 sway bar links, everything as shown in the photo, enough for 1 vehicle
- Will also suit stock non-lifted vehicles simply looking to replace their worn out rear links
- Adjustable to suit lift heights of 2″ to 4″
- Length measured from the center of the lower ball joint to where the first washer sits – 125mm – 165mm (5.0″ – 6.5″)
- Watch a video here to see more about these: https://youtu.be/lZACSaE2PHI
- Note: Product was updated to bigger/thicker stud of the ball joint in 2020, no longer needing the small sleeve shown in the product video. Some vehicles’ sway bar is too thick to use the thick supplied washer, so reuse the stock washer if necessary
(15 reviews) -
ExceptionsFREE SHIPPING
within 48 US StatesDobinsons Tubular UCA Pair | 4Runner FJ Cruiser GX470 GX460
- Suits Toyota 4Runner 4th and 5th Gen 2003-2024, FJ Cruiser all years, Lexus GX470 and GX460
- Complete ASSEMBLED kit for both left and right hand side, includes new ball joints OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Has more clearance around the ball joint than factory UCA’s for better tire clearance
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height, as factory alignment correction will be enhanced with these
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Curved washers face outwards away from bushings during installation, per the product video
- Product Video
- Includes left and right assembled arms, ball joint caps, and hardware to mount ABS lines
- Also sold without ball joints
- Replacement Ball Joints can be ordered here
(8 reviews) -
Airbag Kits
Air Lift 60769 Air Spring Kit Rear Helper Airbags for 2-3″ of Lift
- Suits all 3rd/4th/5th Gen 4Runners, FJ Cruiser, GX470, GX460 WITH 2-3″ of Lift
- Also Suits Toyota Land Cruiser Prado 90 and 95 Models RZJ90, VZJ90, KZJ90, KDJ90, RZJ95, VZJ95, KZJ95, KDJ95
- These are an alternate to Firestone 4108
- Complete kit – 1 per vehicle
- Inserts inside your rear coil springs to add additional load support
- Manually inflate or deflate the air bags to add or remove support or height
- Perfect for people who tow, or regularly load up fully and need additional height or support
- Route the airlines to your rear bumper or a suitable place to easily add or remove air to the bags
- Ships from multiple warehouses across the country for faster shipping times
- Fitment Notes: NOTE: Custom modifications may be required for lifted applications to ensure air bags are properly supported. If using on a lifted application, do not follow bump stop/jounce cut instructions. You will need to determine where to cut based on your lift amount (not cutting off as much depending on lift height)
- Installation Manual, Click Here
(3 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons MRA45-A912 3-Way Adjustable MRA Front Shocks Pair | 80 Series 4″ Lift
- Suits Toyota Land Cruiser 80 Series and Lexus LX450 1990-97, suitable for 4″ of lift
- 3-way adjustable valving – Adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Installation Instructions of the MRA Shocks
- 667mm extended, 401mm compressed
- Bump stop extensions and longer brake lines must be run with these longer shocks
- Full 2 year limited warranty, no set rebuild time period
(15 reviews) -
Upper Control Arms
Pair of UCA Pivot Bolts and Nuts | Toyota and Lexus
- This is a pair of factory size upper control arm pivot bolts and nuts replacements to service two control arms
- Commonly referred to “as the long UCA bolt”
- Services both control arms at once
- Does not come with any washers. New aftermarket UCA’s usually come with the necessary washers
- Vehicle Fitment
-
- 2003-2009 Toyota 4Runner
- 2010-2024 Toyota 4Runner
- 2005-2015 Toyota Tacoma
- 2016-2023 Toyota Tacoma
- 2006+ FJ Cruiser (all years)
- 2003-2009 Lexus GX470
- 2010-2023 Lexus GX460
- Toyota Hilux Vigo
- Toyota Hilux Revo
- Toyota Fortuner
- Toyota Prado 120
- Toyota Prado 150
- Bolt Grade: 10.9
- Head Drive Type: Hex
- Length: 351 mm
- Material: Steel
- SAE or Metric: Metric
- Thread Diameter: 14 mm
- Thread Length: 28.7 mm
- Thread Size: 14 mm
- Thread Type: Fine
(4 reviews)
Cart totals
| Subtotal | $12,574.10 |
|---|---|
| Shipping |
Shipping to FL. |
| Tax | $964.09 |
| Total | $13,818.19 |
