Your cart is currently empty!
FREE SHIPPING
within 48 US States
within 48 US States
Dobinsons Front UCA’s Pair | Ford Ranger USA Spec 2019-2023
- Suits Ford Ranger 2019+ with Steel Knuckles Only
- Complete kit for both left and right hand side, includes new ball joints (installed), OE style rubber frame bushings (installed), and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height of 1.5″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Uses replaceable OE style ball joints, fully sealed for maintenance free life
- Will not work on Aluminum Knuckles!!!
- Product Video
- Installation Instructions
- Images for illustration and detail purposes
$795.00
In Stock
SKU: UCA19-009K
Categories: Control Arms, Dobinsons, Exceptions, Ranger 2019+ (US Spec), Suspension, Upper Control Arms, Upper Control Arms - Ranger
Tags: UCA, uca19
Brand: Dobinsons Spring & Suspension
Description
Ford Ranger UCAs – front upper control arm set. This will ONLY work on a vehicle lifted 1.5″ or more, due to the built-in 3 degrees of caster. These will fit the following vehicles:
- Ford Ranger PX/T7 USA 2019-on – WITH STEEL KNUCKLES ONLY
Kit includes pressed in high quality OE style ball joints, so the Ford Ranger UCAs are ready to bolt into your truck.
These Ford Ranger UCAs will be noise-free as they use rubber bushings and a factory style ball joint. No greasing is necessary.
- Complete kit for both left and right hand side, comes assembled, OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height of 1.5″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Fully sealed OE style ball joints for maintenance free life
These Ford Ranger UCAs will be noise-free as they use rubber bushings and a factory style ball joint. The Dobinsons Ford Ranger UCA’s have a rotated ball joint cup to set the ball joint to the original neutral position even with a lift, and this creates better ride quality while maximizing wheel travel. No greasing is necessary after installation, as the ball joint is sealed and it holds the grease inside with a high quality rubber boot. Zerk fittings are prone to allowing contaminants into the ball joint when regreasing and this will definitely reduce the overall life of the ball joint. Using a fully sealed one keeps out all the junk and gunk from offroad trails whilst requiring no maintenance, just like a factory ball joint. Those are designed to last many many years.
Vehicle Fitment:
2019 Ford Ranger Upper Control Arms
2020 Ford Ranger Upper Control Arms
2021 Ford Ranger Upper Control Arms
2022 Ford Ranger Upper Control Arms
2023 Ford Ranger Upper Control Arms
2024 Ford Ranger Upper Control Arms
2020 Ford Ranger Upper Control Arms
2021 Ford Ranger Upper Control Arms
2022 Ford Ranger Upper Control Arms
2023 Ford Ranger Upper Control Arms
2024 Ford Ranger Upper Control Arms
4 reviews for Dobinsons Front UCA’s Pair | Ford Ranger USA Spec 2019-2023
You must be logged in to post a review.
You may also like…
-
Ranger 2019+ (US Spec)FREE SHIPPING
within 48 US StatesDobinsons IMS Monotube 2.2″ IFP Front Struts Pair | Ford Ranger USA Model 2019-2023
- IMS front struts for 0-3.0″ of lift for Ford Ranger 2019-2023 Models (USA Spec only)
- SOLD IN PAIRS
- Note: Photo is not of actual IMS struts. Ford Ranger IMS have a crossbar style lower front shock bush
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- 495mm extended, 350mm compressed lengths
- Full 2 year limited warranty, no set rebuild time period
- Standard coil seat height is 186mm. See instructions on setting coil seat height on left
- Reuse OE strut top mount
- Can reuse OE coils and add lift via preload or add Dobinsons 1.75″ Light Load or 1.75″ Heavy Load Front Coils
- NOTE: Dobinsons Front Sway Bar Link Kit must be purchased to run Dobinsons IMS struts
(8 reviews)
Related products
-
Dobinsons
Dobinsons Adjustable Rear Sway Bar End Link Kit | 4Runner FJ Cruiser GX470 GX460
- Suits 4th and 5th Gen 4Runner 2003-2024, FJ Cruiser (all years), GX470, GX460 (without KDSS)
- Order 1 for 1 vehicle
- Heavy Duty, zinc plated, with high quality ball joint ends for long life
- Kit includes 2 sway bar links, everything as shown in the photo, enough for 1 vehicle
- Will also suit stock non-lifted vehicles simply looking to replace their worn out rear links
- Adjustable to suit lift heights of 2″ to 4″
- Length measured from the center of the lower ball joint to where the first washer sits – 125mm – 165mm (5.0″ – 6.5″)
- Watch a video here to see more about these: https://youtu.be/lZACSaE2PHI
- Note: Product was updated to bigger/thicker stud of the ball joint in 2020, no longer needing the small sleeve shown in the product video. Some vehicles’ sway bar is too thick to use the thick supplied washer, so reuse the stock washer if necessary
(15 reviews) -
Dobinsons
Dobinsons C59-675V Rear Variable Rate Long Travel Coils | Toyota 4Runner FJ Cruiser GX470 GX460 – Pair
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
- 470mm free height, 16mm wire diameter, 157-230LBF/IN variable spring rate
(15 reviews)$305.00 Select options This product has multiple variants. The options may be chosen on the product page -
80 Series Land Cruiser (1990-1997)
Dobinsons 80 Series Rear Coils Options for Land Cruiser 80 Series 1990-1997 0-6″ Lift – Pair
- Suits Land Cruiser 80 Series and Lexus LX450
- Choose what coil suits your vehicle and needs the best
- Any part number with a V in it means it’s a variable rate/progressive rate spring
- C59-221V – Stock height, variable rate
- c59-269V – 1.75″ Comfort ride spring with only stock weight (variable rate)
- C59-223V – 1.75″ lift with up to 220lbs weight (variable rate), 2.5″ with stock weight
- c59-169 – 1.75″ with up to 220lbs weight
- c59-171 – 2″ lift with 750lbs weight, OR 3″ lift with 440lbs weight
- C97-147VT – 2.5″ lift with 440lbs weight (lifts more with less weight), (variable dual rate long travel)
- c59-167 – 2.5″ with up to 220lbs weight, 2″ with 440lbs weight
- c59-185 – 3″ lift with up to 220LBS weight, 2.5″ with 500LBS, 2″ with 800LBS
- C59-153 – 3″ lift with 880LBS constant rear load
- C59-613V – 3″ lift with up to 200 LBS (Flexi coils, variable rate)
- C97-145VT – 3.5″ lift with 400LBS+ heavy load rear (variable dual rate long travel)
- C59-615V – 4″ lift with up to 200 LBS (Flexi coils, variable rate)
- c59-309 – 4″ lift with 110-220lbs weight
- c59-313 – 4″ lift with 400-750lbs weight
- c59-317 – 6″ lift with stock weight
- c59-319 – 6″ lift with 200LBS constant weight
- C59-311 – 6″ lift with 880LBS constant weight
- Sold in Pairs
- Click HERE to see the FRONT coil options
- Lift heights may vary depending on the age of the vehicle, and all accessories and weight added to it
(6 reviews) -
Dobinsons
Dobinsons GS59-940 Pair Rear Shocks | Tacoma 05-23 Tundra 00-06
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals
- Fuchs German shock absorber oil
- Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings
- Double Chrome hardened rods
- Metal shock boots to protect rod from damage
- Matched to compliment Dobinsons Complete Suspension Systems
- Dobinsons GS59-940 Specifications: 614mm extended, 361mm compressed, 50mm body size
- Pin mount top, eyelet lower
- Available in Yellow or Black
- Sold in pairs
(6 reviews)$310.00 Select options This product has multiple variants. The options may be chosen on the product page
Nicholas (verified owner) –
Good quality, really nice.
Benjamin (verified owner) –
Good quality, really nice.
Timothy (verified owner) –
5 Stars!!
Kevin (verified owner) –
Would definitely buy from this site again.