Your cart is currently empty!
FREE SHIPPING
within 48 US States
within 48 US States
Take 10% off with Coupon
Code "BLACKFRIDAY"!!
Code "BLACKFRIDAY"!!
SPC 25485 | UCA’s for 2001-07 Sequoia & 1999-06 Tundra Pair
- Suits 2001-07 Toyota Sequoia & 1999-06 Toyota Tundra
- Improved clearance to get around the spring bucket
- 80° of articulation in its ball joint
- SPC’s arm gives you maximum droop travel.
- SPC’s arms have +1° of caster built into them
- Arm will get you 0° to +4° of caster and ±2° of camber
- Maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming
- Installation Instructions
$895.96
In Stock
EAN: 82642254850
SKU: 25485
Categories: Exceptions, Performance Upgrades - Sequoia 1st Gen, Sequoia 1st Gen (2001-2007), SPC, Suspension, Tundra 1st Gen (2000-2006), Upper Control Arms
Brand: SPC
Description
SPC 25485 Upper Control Arm Set. SPC has been at the forefront of designing and building rugged, adjustable front upper control arms for the demands of lifted vehicles. Trucks and SUVs run out of factory alignment adjustment when you install lift kits. With our patented design our upper control arms provide additional camber and caster change. Tough enough for off-road and racing applications, SPC arms are the industry standard.
SPC 25485 – Adjustable Upper Control Arms
2001 to 2007 Toyota Sequoia: 1999 to 2006 Toyota Tundra
Improve droop travel, drivability and tire wear as well as adjusting tire position in your wheel well with SPC’s adjustable front upper control arms. Featuring an upgraded greaseable ball joint and SpecRide™ bushings, this arm is designed to correct alignment angles while maintaining factory ride quality. SPC’s integrated tubular and cast steel designs provide the strength and durability needed for the most demanding environments. These remove and replace arms are sold in pairs.
- Get more droop travel: SPC’s arm has improved clearance to get around the spring bucket. With 80° of articulation in the upgraded ball joint and free pivoting bushings, SPC’s arm gives you maximum droop travel.
- Get your drivability and tracking back: When you lift your truck you affect caster and camber. SPC’s arms have +1° of caster built into them. Using its patented ball joint design the arm will get you 0° to +4° of caster and ±2° of camber, so you can put your alignmnet angles back to specification.
- Get your tire where you want it in the wheel well: Use adjustment in the control arm and on the OE lower cams to maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming.
Front Adjustment range:
Camber:±2.00°
Caster: 0.0° to +4.00°
Installation time: .8 hr/side
Required: 1 per axle
Patent No. US 7,513,514
Vehicle Fitment:
2001 Toyota Sequoia SPC Upper Control Arms
2002 Toyota Sequoia SPC Upper Control Arms
2003 Toyota Sequoia SPC Upper Control Arms
2004 Toyota Sequoia SPC Upper Control Arms
2005 Toyota Sequoia SPC Upper Control Arms
2006 Toyota Sequoia SPC Upper Control Arms
2007 Toyota Sequoia SPC Upper Control Arms
2000 Toyota Tundra SPC Upper Control Arms
2001 Toyota Tundra SPC Upper Control Arms
2002 Toyota Tundra SPC Upper Control Arms
2003 Toyota Tundra SPC Upper Control Arms
2004 Toyota Tundra SPC Upper Control Arms
2005 Toyota Tundra SPC Upper Control Arms
2006 Toyota Tundra SPC Upper Control Arms
11 reviews for SPC 25485 | UCA’s for 2001-07 Sequoia & 1999-06 Tundra Pair
You must be logged in to post a review.
Related products
-
SuspensionOn Sale All November!!ETA is late December
Dobinsons Tubular UCA Pair | Tacoma Hilux Fortuner 2005-23
- Suits Toyota Tacoma from 2005 to 2023, Toyota Hilux Vigo and Revo from 2005+, and Toyota Fortuner 2005 to 2023
- Complete assembled kit for both left and right hand side, includes new ball joints, ball joint caps, OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Has more clearance around the ball joint than factory UCA’s for better tire clearance
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height of 1.5″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Product Video
- Also sold without ball joints
- Replacement Ball Joints can be ordered Here
(9 reviews) -
Sale!DobinsonsOn Sale All November!!
Dobinsons Front 30mm Polyurethane Coil Spacer (Single) Toyota Land Cruiser 80 105
- Suits Land Cruiser 80 Series and Lexus LX450
- High Quality Polyurethane, maintains height over time
- Perfect fit between OE isolator and coil seat
- Sold individually, available front and rear for several vehicles
- Lasts longer than rubber
- Easy to add lift height for worn coils
(4 reviews) -
Sale!Tacoma 3rd Gen (2016-2023)On Sale All November!!
Dobinsons 0-3″ Lift Kit Toyota Tacoma 2016-2023 with Blocks or AAL
- 4×4 Access Cab models come with 1″ front lift from the factory. Lift heights listed are for Dual cab 4×4 models. Subtract 1″ for access cab models
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Normal kit Includes 2 Front Struts, 2 Rear Shocks, 2 Front Coil Springs (a pair), Rear Spacer Blocks and U-Bolts
- You can now select to use Wheeler’s Add-A-Leaf Kit instead of the Quick Ride Kit if you’d prefer
- For rear lift, choose either the Quick Ride Kit or an Add-A-Leaf kit
- Select desired lift height and additional options
(13 reviews) -
Sale!DobinsonsOn Sale All November!!
Dobinsons Front IFS Diff Drop Kit | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits 2005-23 Toyota Tacoma, 2003-2024 4Runner, 2007-16 FJ Cruiser, Lexus GX470, GX460
- Keeps CV angles at a good working angle
- Suitable for lifts over 2.0″. There’s really no benefit to adding them if there’s less lift than 2.0″
- Includes all necessary hardware, including machined spacers and nuts/bolts
- Includes 2 different lengths of the long bolts as some vehicles need them longer than others
- Compliments Dobinsons 3″ lifts for IFS Toyota and Lexus vehicles
- Simply remove the front skid plate, remove the 2 long bolts at the front of the diff, install the spacers and long bolts supplied, install the skid plate spacers and longer bolts supplied while reinstalling the skid plate
- Note: Some aftermarket skid plates have spacers built-in so the small spacers aren’t necessary, and some skid plates may use larger bolts to install it to the vehicle, requiring modification to the supplied spacers
- Installation Instructions
(17 reviews)
Benjamin (verified owner) –
Spoke with Mike, he got me headed in the right direction for what I need.
Benjamin (verified owner) –
Good quality, really nice.
Andrew (verified owner) –
Great description on the page, easy to understand what I was buying.
Daniel (verified owner) –
Very fast delivery.
Jeremy (verified owner) –
Very fast delivery.
Nathan (verified owner) –
Very good customer service, super friendly.
Brian (verified owner) –
Very good customer service, super friendly.
Nathan (verified owner) –
Exit Offroad really does know what they’re talking about, they have the best product pages.
Stephen (verified owner) –
This is my go-to now for off road parts.
David (verified owner) –
Value for money, super satisfied.
Robert (verified owner) –
It’s exactly what I wanted.