Your cart is currently empty!
Dobinsons SE29-575 Rear Extended Sway Bar Link Kit | Jeep Gladiator
- Fits Jeep Gladiator JT 2020+
- Recommended for a Jeep with 2″ of lift
- Required for a Jeep with 3″ of lift
- Heavy Duty design with high quality ball joint ends for long life
- Fits and installs the same as OEM, but with added length so that the stock sway bar still functions normally at a lifted height without reducing wheel travel
- Sold as a pair, enough for 1 vehicle
$90.00
In StockDescription
Pair of Dobinsons SE29-575 Rear Extended Sway Bar Link Kit | Jeep Gladiator Jeep Gladiator JT 2020+.
- Fits Jeep Gladiator JT 2020+
- Recommended for a Jeep with 2″ of lift
- Required for a Jeep with 3″ of lift
- Heavy Duty design with high quality ball joint ends for long life
- Fits and installs the same as OEM, but with added length so that the stock sway bar still functions normally at a lifted height without reducing wheel travel
- Sold as a pair, enough for 1 vehicle
Many people don’t realize that when lifting their vehicle, the sway bar angle because a lot steeper than normal, and this actually affects the wheel travel and ride comfort inside the vehicle. The sway bar links are literally stretched out and causing a type of binding on the rear sway bar not being able to do its job properly. By changing out the original swaybar links to the Gladiator rear swaybar links by Dobinsons, you can set the angle back to a more neutral position, gaining wheel travel, gaining ride comfort, and also helping the swaybar to properly assist the vehicle in keeping it more level when cornering. These Gladiator rear swaybar links should be used at any lift height of over 2″ so that you get the proper articulation from your new suspension kit, and are required with a lift height of 3″ or more. You’ll also notice that if you don’t have longer sway bar links installed, reinstalling the original links can be quite difficult as they’re very tight on a lifted Jeep.
Related products
-
Dobinsons
Dobinsons GS59-574 Pair Extended Travel Struts FJ Cruiser 2010+ 4Runner 2010+ GX460
- Suits Toyota FJ Cruiser 2010+ and Toyota 4Runner 5th Gen 2010-2024, and Lexus GX460 (all years) for 2.0″ to 3.5″ of lift
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals
- Fuchs German shock absorber oil
- Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- Matched to compliment Dobinsons Complete Suspension Systems
- Dobinsons GS59-574 Specifications: Extended Travel – 575mm extended, 430mm compressed, 54mm body size
- Dobinsons GS59-574 struts add 1″ to the listed coil spring that are used with them, due to the raised coil seat. They are also longer than stock for taller lifts
- Example: Use a 2″ lift spring with these struts to get 3″ of lift
$350.00 Select options -
Dobinsons
Dobinsons C59-476 1.75″ Front Coils for Toyota Sequoia 2008-2022 5.7L V8
- Dobinsons C59-476 Front 45mm Lift Coils, sold as a pair – suits Toyota Sequoia 2008 to 2022 5.7L V8 models
- Not suitable on vehicles that came with factory rear air suspension
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- 367mm free height, 19mm wire, 685LBF/in rate
- Sold in Pairs
$405.00 Add to cart -
GX460 (2010-2023)
Dobinsons 1.5-3.5″ Lift Kit for Lexus GX460 2010 to 2023 (all options)
- Every suspension option from Dobinsons to lift your Lexus GX460 all on one page
- Here you can lift from a low height up to the maximum bolt-on lift height by making your selections below
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base Kit Includes 2 Front Twin Tube Struts, 2 Rear Twin Tube Shocks, and 4 Coil Springs
- You can choose to upgrade to the higher end IMS or MRA struts and shocks on this page in the drop down menus
From $1,200.00 Select options -
SuspensionShips FREE !!
within 48 US StatesDobinsons MRA59-A687 3-Way Adjustable MRA Rear Shocks | 80 Series 4″ Lift
- Suits Toyota Land Cruiser 80 Series 1990-97, suitable for 4-5″ of lift, or when used in a long travel setup
- 3-way adjustable valving – Adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Piggyback Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- 674mm extended, 420mm compressed
- Installation Instructions of the MRA Shocks
$1,350.00 Add to cart