Your cart is currently empty!
Dobinsons 1″ Front Bump Stop Extensions | Jeep Wrangler JL & Gladiator JT
- Suits 2018+ Jeep Wrangler JL 2-door, 2018+ Jeep Wrangler JL 4-door, 2020+ Jeep Gladiator JT
- 25mm / 1.0″ Extension to protect shocks from bottoming out
- Sold as a pair, spacing down the two front bump stops
- Required when lifting 3″ with a Dobinsons Suspension
- Also required for fitting 35″ tires on a non-Rubicon model due to flare clearance
$70.00
In Stock
SKU: BS29-566
Categories: Bump Stops & Spacers, Dobinsons, Gladiator JT (2020-2024+), JL Wrangler (2018-2024+), Suspension
Tags: bump, bumpstop, extension, stop
Brand: Dobinsons Spring & Suspension
Description
Dobinsons BS29-566 are sold as a pair, need 1 pair per vehicle.
Whenever adding bigger tires, or doing a full suspension kit on an older vehicle, the original bump stops may not be suitable and not long enough. These Dobinsons Jeep bump stop extensions are the answer, allowing you to properly set the bump stop clearance height to the axle when lifting your Jeep by 3″
Dobinsons BS29-566 Bump Stop Extensions Kit Suits the following range of vehicles:
- 2018+ Jeep Wrangler JL 2-door
- 2018+ Jeep Wrangler JL 4-door
- 2020+ Jeep Gladiator JT
When driving hard off road, it’s extremely common to come across some uneven terrain too quickly and risk bottoming out the front end. The easiest damage that can happen from doing this is if you bottom out the front struts. This hard impact can have really negative long term effects on the seals in the front struts, and repeated bottoming out can lead to early failure far sooner than what they were intended to do. By setting the correct amount of bump stop clearance up front, your bump stops will properly bottom out on the front lower control arms before the strut has a chance to hit full compression, therefore saving some life out of it. These Dobinsons BS29-566 bump stop extensions come set with 25mm extended length, which adds the correct amount of additional spacing to your bump gap to compensate for the lifted height you are running at and the additional travel your shocks have. Aftermarket shocks with a longer compressed length than stock should be running longer bump stops so that they bottom out at the appropriate time.
Vehicle Fitment:
2018 Jeep Wrangler
2019 Jeep Wrangler
2020 Jeep Wrangler
2021 Jeep Wrangler
2022 Jeep Wrangler
2023 Jeep Wrangler
2024 Jeep Wrangler
2019 Jeep Wrangler
2020 Jeep Wrangler
2021 Jeep Wrangler
2022 Jeep Wrangler
2023 Jeep Wrangler
2024 Jeep Wrangler
2020 Jeep Gladiator
2021 Jeep Gladiator
2022 Jeep Gladiator
2023 Jeep Gladiator
2024 Jeep Gladiator
2021 Jeep Gladiator
2022 Jeep Gladiator
2023 Jeep Gladiator
2024 Jeep Gladiator
You must be logged in to post a review.
You may also like…
-
Dobinsons
Dobinsons IMS29-60736 Front 2.6″ IMS Shocks Pair | Jeep Gladiator & JL Wrangler
- Fits Jeep Gladiator JT 2020+ and Jeep Wrangler JL 2018+ 2-door and 4-door
- Suits vehicles with 2-3.5″ of lift
- SOLD IN PAIRS
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- 682mm extended, 425mm compressed
(13 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons 3-Way Adjustable MRA Front Shocks Pair | Wrangler JL + Gladiator JT (2-4″ lift)
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Piggyback Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Sold in Pairs
- 677mm extended, 425mm compressed
(15 reviews)
Related products
-
80 Series Land Cruiser (1990-1997)
Dobinsons 80 Series Stock Height Restoration Suspension Kit (inc all shock options)
- Suits Land Cruiser 80 Series and Lexus LX450
- Restore your vehicle back to the original ride height, and bring the ride quality way up at the same time with the Dobinsons 80 Series Stock Height Suspension Kit
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to match OE spec and height
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Includes 2 Front Shocks, 2 Rear Shocks, and 4 Coil Springs. Add on additional parts if desired
(18 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesETA is late DecemberDobinsons Tubular UCA Pair | Tacoma Hilux Fortuner 2005-23
- Suits Toyota Tacoma from 2005 to 2023, Toyota Hilux Vigo and Revo from 2005+, and Toyota Fortuner 2005 to 2023
- Complete assembled kit for both left and right hand side, includes new ball joints, ball joint caps, OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Has more clearance around the ball joint than factory UCA’s for better tire clearance
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height of 1.5″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Product Video
- Also sold without ball joints
- Replacement Ball Joints can be ordered Here
(9 reviews) -
Dobinsons
Dobinsons Greasable Bolt Pair | Ford Nissan and Toyota (SP59-060)
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Kit includes 2 greasable bolts, as shown in the photo
- Order 2 kits if you want to replace fixed and shackle end bolts
- Suits Toyota Tundra and Tacoma as well as Nissan Frontier D40 and D41, Ranger 2019+. See full vehicle list below
(12 reviews) -
80 Series Land Cruiser (1990-1997)
Dobinsons 3.5-4″ Lift Kit Builder | Land Cruiser 80 Series 1990-97 (inc all shock options)
- Suits Land Cruiser 80 Series and Lexus LX450
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- **Kit photo shows with every additional option purchased**
- Coils are specifically suited to match OE spec and height
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- A Standard 4″ Base Kit should include front and rear shocks and coils, 5 degree castor plate kit, Front and Rear adjustable panhard rods, front sway bar extensions and rear proportioning valve extension and brake lines. Make selections below
- Select from Dobinsons Twin Tube, IMS Monotube, or MRA 3-way Adjustable Monotube Remote Reservoir shocks
- You must choose what coils, shocks and other components you want to add
(13 reviews)
Reviews
There are no reviews yet.