Dobinsons BS29-566 Front Extended Bump Stops Jeep Wrangler JL Gladiator JT

Dobinsons 1″ Front Bump Stop Extensions | Jeep Wrangler JL & Gladiator JT

Suits 2018+ Jeep Wrangler JL 2-door, 2018+ Jeep Wrangler JL 4-door, 2020+ Jeep Gladiator JT
25mm / 1.0″ Extension to protect shocks from bottoming out
Sold as a pair, spacing down the two front bump stops
Required when lifting 3″ with a Dobinsons Suspension
Also required for fitting 35″ tires on a non-Rubicon model due to flare clearance

$70.00

In Stock

SKU: BS29-566 Categories: Bump Stops, Dobinsons, Gladiator JT 2020-2024+, JL Wrangler 2018-2024+, Suspension Tags: bump, bumpstop, extension, stop Brand: Dobinsons Spring & Suspension

Description

Description

Dobinsons BS29-566 are sold as a pair, need 1 pair per vehicle.

Whenever adding bigger tires, or doing a full suspension kit on an older vehicle, the original bump stops may not be suitable and not long enough. These Dobinsons Jeep bump stop extensions are the answer, allowing you to properly set the bump stop clearance height to the axle when lifting your Jeep by 3″

Dobinsons BS29-566 Bump Stop Extensions Kit Suits the following range of vehicles:

2018+ Jeep Wrangler JL 2-door
2018+ Jeep Wrangler JL 4-door
2020+ Jeep Gladiator JT

When driving hard off road, it’s extremely common to come across some uneven terrain too quickly and risk bottoming out the front end. The easiest damage that can happen from doing this is if you bottom out the front struts. This hard impact can have really negative long term effects on the seals in the front struts, and repeated bottoming out can lead to early failure far sooner than what they were intended to do. By setting the correct amount of bump stop clearance up front, your bump stops will properly bottom out on the front lower control arms before the strut has a chance to hit full compression, therefore saving some life out of it. These Dobinsons BS29-566 bump stop extensions come set with 25mm extended length, which adds the correct amount of additional spacing to your bump gap to compensate for the lifted height you are running at and the additional travel your shocks have. Aftermarket shocks with a longer compressed length than stock should be running longer bump stops so that they bottom out at the appropriate time.

You may also like…

Suspension
Ships FREE !!
within 48 US States
Dobinsons 3-way Adjustable MRA Front Shocks | Wrangler JL, Gladiator JT (2-4″ lift)
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Piggyback Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Sold in Pairs
- 677mm extended, 425mm compressed
$1,350.00 Add to cart
Dobinsons
Ships FREE !!
within 48 US States
Dobinsons IMS29-60736 Front 2.6″ IMS Shocks for Jeep Gladiator and JL Wrangler
- Fits Jeep Gladiator JT 2020+ and Jeep Wrangler JL 2018+ 2-door and 4-door
- Suits vehicles with 2-3.5″ of lift
- SOLD IN PAIRS
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- 682mm extended, 425mm compressed
$650.00 Add to cart