Your cart is currently empty!
Dobinsons 0-3.5″ Pre-Assembled Twin Tube Tacoma Coilovers for 2005-2023
- Suits 2005-2023 Toyota Tacoma 4×4 Double Cab Short Bed
- 4×4 Access Cab models come with 1″ front lift from the factory. Lift heights listed are for Dual cab 4×4 models. Subtract 1″ for access cab models
- Set of twin tube coilovers for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Choose the appropriate coils to match the lift height you want that also suits the added weight you have on the vehicle
- Nitrogen Gas Charged Struts, Superior Design, thicker walls, longer travel
- Direct Bolt-in Replacements, Pre-Assembled and Ready To Go
- 32mm Bore Size, Double Chromed 18mm Rod
- 51mm Body Size
- High Quality Fuch’s German Shock Oil
- NOK Multi-Lip Seals
- Teflon Piston Rings
- Natural Rubber Bushings for the Best NVH Dampening
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Built to order
- Lift heights are subject to variations in vehicle years as well as accessory weights, engine differences, and other variables.
From $865.00
In StockC59-238 - 0-1/4" lift Closest to stock height
C59-300 - 1" Lift with stock front end
C59-302 - 1.6" Lift stock front end, 1.25" with light bumper OR winch
C59-314 - 2" lift stock front end, 1.75" with 100LBS
C59-350 - 1.5" to 1.75" with 110-220LBS, 2" with stock weight (heavy rate)
C59-352 - 2" lift with 110-220 lbs, or 2.5" with stock weight (heavy rate)
C59-354 - 2.4" lift with 110-220LBS, or 2" with 230-300LBS (heavy rate)
GS59-221 - Twin Tube - standard coil seat height (0-2.5", yellow only)
GS59-220 - Twin Tube - extended travel, adds 1" lift to coil lift height (2.5-3.5")
Description
Tacoma Coilovers – Dobinsons offer this twin tube coilover set for the 2005-2023 Toyota Tacoma 4×4 Double Cab Short Bed, Tacoma Coilovers are designed to give a great ride front and rear, for stock vehicles looking for new front suspension, with various load rating options to get the correct lift height and load support for how your vehicle is built. Tacoma Coilovers are a quick way to pull out and remove your original front struts setup and bolt in a set of Pre-Assembled Tacoma Coilovers from Dobinsons, ready to go at the lift height you choose.
Designed, developed and tested in Australia by Dobinsons Spring & Suspension, in-house suspension design engineers, Dobinsons 4×4 shock absorbers and coil springs are designed and tested to perform in the harshest conditions right across the world. As Dobinsons export to over 40 countries worldwide from their Australian head office, the importance of quality is at the forefront in the complete design and manufacturing process. This ensures every shock and coil spring can withstand the blistering heat and corrugations of the Australian outback right through to the subzero temperatures of a Russian winter.
Dobinsons Twin Tube Nitrogen Gas charged shock absorbers are made from the world’s highest quality external and internal parts sourced worldwide. They provide a significant increase in performance over the standard shock absorbers. Dobinsons twin tube shock absorbers feature larger bodies, larger bores and increased valving performance to dramatically improve vehicle handling and control and reduces shock fade.
We proudly manufacture the highest quality replacement coil springs for many different applications, complying to ISO9001:2008 international quality standards from our state of the art manufacturing facility in Central Queensland, Australia.
All Dobinsons™ coil springs are load tested and scragged 100% to eliminate subsequent spring sag. We also perform spring fatigue and hardness testing using in-house state of the art testing equipment.
Note: If you have a single cab, or a 2 Wheel Drive Pre-Runner, contact us first for suspension, otherwise the lift height and ride quality may be different than listed here.
10 reviews for Dobinsons 0-3.5″ Pre-Assembled Twin Tube Tacoma Coilovers for 2005-2023
You must be logged in to post a review.
You may also like…
-
SPCFREE SHIPPING
within 48 US StatesSPC 25470 | UCA’s for Tacoma 2005-2023 Pair
- Suits Toyota Tacoma 2005-2023 4×4 and Prerunner
- Improved clearance to get around the spring bucket
- 80° of articulation in its ball joint
- SPC’s arm gives you maximum droop travel.
- SPC’s arms have +2° of caster built into them
- Arm will get you 0° to +4° of caster and ±2° of camber
- Maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming
- Now with updated maintenance-free sealed ball joints
- Installation Instructions
- We offer replacement ball joints as well
(10 reviews) -
TimbrenFREE SHIPPING
within 48 US StatesTimbren ABSTOF Active Off Road Front Bump Stops | Toyota and Lexus
- Suits 2000-2024 Tundra, 2001-2024 Sequoia, 2005-2023 Tacoma, 1990-2024 4Runner, FJ Cruiser, Lexus GX470 and GX460, Landcruiser 100 and 200 Series
- Also Suits Toyota Land Cruiser Prado 90 and 95 Models RZJ90, VZJ90, KZJ90, KDJ90, RZJ95, VZJ95, KZJ95, KDJ95
- Note: Some 2nd Gen Toyota Sequoia models have 2 sets of front bump stops, so ordering 2 of these kits will be necessary to replace them all. Inspect your vehicle before ordering
- Maintain Full Axle Travel
- Smooth Axle Engagement and Disengagement
- Enhance Suspension Performance
- Progressive Spring Rate
- Absorbs Energy and Cushions Road Shocks
- Stronger Than OEM Bumpstops
- Easy Installation – Installation Video
- Satisfaction Guarantee
- Lifetime Warranty
- Click here for instructions
(12 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesETA is late DecemberDobinsons Tubular UCA Pair | Tacoma Hilux Fortuner 2005-23
- Suits Toyota Tacoma from 2005 to 2023, Toyota Hilux Vigo and Revo from 2005+, and Toyota Fortuner 2005 to 2023
- Complete assembled kit for both left and right hand side, includes new ball joints, ball joint caps, OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Has more clearance around the ball joint than factory UCA’s for better tire clearance
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height of 1.5″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Product Video
- Also sold without ball joints
- Replacement Ball Joints can be ordered Here
(9 reviews) -
TimbrenFREE SHIPPING
within 48 US StatesTimbren ABSTRFK Tacoma U-Bolt flip and Active Bump Stops Kit | 2005-2023 Tacoma
- Suits 2005 to 2023 Toyota Tacoma 4×4 models
- Maintain Full Axle Travel
- Smooth Axle Engagement and Disengagement
- Enhance Suspension Performance
- Progressive Spring Rate
- Includes incorporated u-bolt flip kit for additional clearance below
- Absorbs Energy and Cushions Road Shocks
- Stronger Than OEM Bumpstops
- Easy Installation
- Satisfaction Guarantee
- Lifetime Warranty
- Click here for instructions
(14 reviews)
Joshua (verified owner) –
5 Stars!!
Matthew (verified owner) –
This is my go-to now for off road parts.
Jeffrey (verified owner) –
Value for money, super satisfied.
Stephen (verified owner) –
Very good customer service, super friendly.
Kevin (verified owner) –
Very good customer service, super friendly.
Matthew (verified owner) –
Very fast delivery.
Scott (verified owner) –
It’s exactly what I wanted.
John (verified owner) –
I received it really fast.
Steven (verified owner) –
Would definitely buy from this site again.
Chad (verified owner) –
It’s exactly what I wanted.