Your cart is currently empty!
Exit Offroad - The Ultimate Resource for Dobinsons Suspension in the USA
Dobinsons Suspension | Timbren Bump Stops | Dirt King Suspension | Overland Vehicle Systems | Bilstein Shocks | SPC UCA's | Powerbrake Brake Kits | Long Range Gas Tanks | Icon Suspension | Rusty's Offroad | Air Locker | Firestone Airbags | RCI Offroad | All Pro Offroad | Trail Gear | Maxtrax | Apache Offroad | RCV Axles | Treaty Oak Offroad | Asfir Skid Plates
Check these Out
-
Sale!
ARBPrice Increase Coming June 2ndARB710LB Orange Snatch Strap Recovery 30′ x 3 1/4″ (24000 LB)
- A snatch strap is a Kinetic strap that stores energy to magnify the pulling power during a vehicle recovery
- Min. breaking strength: 12,500kg / 24000lb Specifically designed to stretch under load for maximum performance
- An ARB snatch strap is a very effective method of extracting a bogged or immobilized 4wd when a second vehicle is present
- Length: 9m / 30 feet. Width: 80mm / 3 1/4″
- Material: 100 percent nylon, Elasticity: Stretch (genuine) 20 percent. The kinetic energy generated by the elasticity aids with the recovery itself, while at the same time reducing the likelihood of vehicle damage.
- Reinforced Eyes. For vehicle recovery, a snatch strap is more suitable than a tow strap.
- All ARB snatch straps are woven and fabricated to ARB specifications, and tested by a NATA approved laboratory
- Part no. ARB710LB
- Min. breaking strength: 12,500kg/24000lb
- Length: 9m / 30 feet
- Width: 80mm / 3 1/4″
- Elasticity: Stretch (genuine) 20%
- Material: 100% nylon
- Reinforced eyes: yes
- Eye & seam protector sleeves: yes
(9 reviews) -
Sale!ARBPrice Increase Coming June 2nd
ARB 171503 Air Compressor Manifold Kit
- Air Locker Manifold Kit enables the installation of Air Locker solenoids to an ARB Twin Compressor
- Complete manifold kit to suit Air Locker solenoid mounting on the ARB On-Board Twin Air Compressor Kits.
- This kit includes a manifold body with mounting bracket, BSP ports, NPT ports, high temperature resistant braided hose, NPT connection nipples and M6 hex head bolts and nylon lock-nuts which secure this kit.
- This manifold permits you to lock the front and rear air lockers without needing a compressor for each.
- Manifold body with mounting bracket
- 2 x 1/8″ BSPP ports for installation of up to 2 x Air Locker solenoids
- 2 x 1/4″ NPT ports, one to be used as an input and the second could be used for installation of a pump up kit (ARB 171302)
- 1 x high temperature resistant Teflon stainless steel braided hose with heavy duty JIC4 fittings
- 2 x JIC4 – 1/4″ NPT nipples to connect the included hose to the compressor outlet and manifold kit input
- 2 x M6 hex head bolt and nylon lock-nuts for securing the manifold kit
(3 reviews) -
Sale!Air CompressorsFREE SHIPPING
within 48 US StatesPrice Increase Coming June 2ndARB CKSA12 High Performance Small 12V Air Compressor
- Designed specifically to run one or two Air Lockers
- Constructed of lightweight, high-strength, engineering-grade materials, including military and aerospace-grade components
- Relocatable, splash-resistant air filter with washable high-flow sintered bronze filter cartridge for cleaner, cooler air supply
- Fully sealed components for moisture and dust protection
- Over-pressure safety valve-equipped
- Pressure switch-controlled air manifold system specially designed for ARB Air Lockers
- Hard-anodized cylinder bore and PTFE-impregnated carbon fiber piston seal for reduced friction and maximum life
- Anti-vibration, sound-deadening, anodized mount dissipates motor heat and allows compressor to be repositioned 180 degrees
- Ball bearing-equipped motor (no bushings) with unique, linear brush, pre-load system for long life, low heat, and quiet operation
- Compressor piston equipped with a German-made, high shock-rated, cylindrical roller bearing
- Motor is internally thermal-protected against extreme temperature damage
- Comprehensive-photo illustrated installation guide
- 12V DC, Draws 5.5 Amps, 0.98 CFM, 100 PSI max
(6 reviews) -
Sale!100 Series Land Cruiser IFS (1998-2007)Price Increase Coming June 2nd
OME 2860 Rear Coil Springs | Land Cruiser 80 and 100 Series – Pair
- OME Part Number 2860
- Bar Size : 17 mm
- Free Height : 480/490mm
- Number of Turns : 6.88
- Coil Weight (each): 6 Kg | 13.2 lbs
- Spring Rate : 220 lbs
- Sold in Pairs
(26 reviews) -
Sale!4Runner 4th Gen (2003-2009)Price Increase Coming June 2nd
OME 2895 Rear Coil Springs | 4Runner FJ Cruiser GX470 GX460 – Pair
- OME Part Number 2895
- Bar Size : 16.5 mm
- Free Height : 390mm
- Number of Turns : 6.21
- Coil Weight (each): 4.6 Kg | 10.1 lbs
- Spring Rate : 260 lbs
- Sold in Pairs
(13 reviews) -
Sale!WinchesFREE SHIPPING
within 48 US StatesBrute Recovery Winch Line With Synthetic Soft Shackle 3/8″x 99′
• UV Stable synthetic rope construction
• 99’ Long, 3/8” Thick
• 3-inch Class 2 Diamond Knot
• Light weight for easy use on the trail
• Created and designed with safety on the trail
• Soft Shackle integrated for trail convenience(5 reviews) -
Sale!Skid Plates - LC250RCI On Sale Now !!!
RCI Land Cruiser 250 Engine Skid Plate | 2024-2025
- Suits Toyota Land Cruiser 250 from 2024+
- Protects front two cross-members, low hanging front differential, and oil pan
- Service openings for easy service and oil changes without removal
- Reinforced edges between cross-members for maximum strength and rigidity
- Bolt protector rings surround exposed bolts, shielding against physical damage
- Smooth, flat surface that easily slides over obstacles
- Black powder coat available for rust resistant, durable and high quality finish
- Utilizes Center mounting points for maximum strength whether steel or aluminum
- Installs in minutes
- All hardware provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- Made in the USA
- INSTALL GUIDE (Click Here)
(0 reviews) -
Sale!Differential | DrivetrainFREE SHIPPING
within 48 US StatesPrice Increase Coming June 2ndARB RD146 Rear Tundra Air Locker 5.7L V8 10.5″
- For Use only with Toyota Tundra 5.7L V8 REAR 2007 to 2021 with 10.5″ 12 Bolt Ring Gear and 36 spline axles
- Will not suit 4.6L or 4.7L engines, as they use a smaller rear differential (RD152)
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
(11 reviews)
-
4Runner 5th Gen (2010-2024)FREE SHIPPING
within 48 US StatesDobinsons Toyota 4Runner IMS Suspension Kit for 2010-24 (1-3.5″)
- Suits Toyota 4Runner 5th Gen 4×4 from 2010 to 2024, with or without KDSS
- If you have a 2WD model, add 1″ to the listed lift heights of the front coils due to the lighter front weight of the vehicle
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Rear coil springs are optional in case you don’t want to lift the rear, and just lift the front
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Dobinsons have the largest selection of front and rear coils for 4Runners and in multiple colors
- Add up how much accessory weight you have on the front and then the rear, that’s your constant load
- Then choose the lift height from the coils that most closely matches the added weight
- Fully rebuildable and re-valvable shocks and struts
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Option to have the front struts preassembled prior to shipping to make installation easier at home
- Base Kit Includes 2 Front IMS Monotube Struts, 2 Rear IMS Monotube Shocks, and 4 Coil Springs – Select your preferences
- You can go from a standard suspension to full long travel with all the options listed here
- The more lift height you add, the more parts you need, so read the subsection headings below
- Lift heights are based on the standard 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. Many vehicles come in at different heights from the factory based on trim levels and options
- Suspension Installation Video
(23 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons Lift Kit for Toyota 4Runner 4×4 2003-2009 (All Options 0-3.5″)
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- If you have a 2WD model, add 1″ to the listed lift heights of the front coils due to the lighter front weight of the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Choose 2 Front Twin Tube Struts, 2 Rear Twin Tube Shocks, and 4 Standard Coil Springs for a full kit, and go from there
- For information and specs on the products in the drop down lists below, select an item, then click the small square box that will appear to the right to be taken to that product page
- You can choose from Dobinsons Classic Twin Tube Shocks, IMS Monotube, or MRA remote resi shocks with 3-way valving adjustment
- Note: To get 3″ of front lift with the twin tube struts, use GS59-220 struts (which add 1″ of lift) with suitable 2″ lifted coils to get 3″ of lift. C59-300 with GS59-220 lift a V6 3.0″ with stock weight, and C59-302 with GS59-220 lift 3.0″ on a V8 model.
- Select front coils based on which engine you have
(12 reviews) -
4Runner 5th Gen (2010-2024)FREE SHIPPING
within 48 US StatesDobinsons Build-A-Kit Toyota 4Runner 2010-24 (All Options 1-3.5″)
- Suits Toyota 4Runner 5th Gen 4×4 Models 2010-2024, with or without KDSS
- If you have a 2WD model, add 1″ to the listed lift heights of the front coils due to the lighter front weight of the vehicle
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Rear coil springs are optional in case you don’t want to lift the rear, and just lift the front
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Add up how much accessory weight you have on the front and then the rear, that’s your constant load
- Then choose the lift height from the coils that most closely matches the added weight
- Dobinsons Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel, linear rate
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Dobinsons have the largest selection of front and rear coils for 4Runners and in multiple colors
- Base Kit Includes 2 Front Twin Tube Struts, 2 Rear Twin Tube Shocks, and Front Coil Springs – Select your preferences
- You can go from a standard suspension to full long travel with all the options listed here
- The more lift height you add, the more parts you need, so read the subsection headings below
- Learn more about the 3 different shock types on this blog post
- Lift heights are based on the standard 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. Many vehicles come in at different heights from the factory based on trim levels and options
- Rear coils are optional and not included by default, in case you only want to lift the front and keep the stock rear coils in place
- Suspension Installation Video
- All Dobinsons parts have a full 2 year warranty
(23 reviews) -
Suspension
Dobinsons Tacoma Lift Kit for 2005-2023 4×4 (all options)
- 4×4 Access Cab models come with 1″ front lift from the factory. Lift heights listed are for Dual cab 4×4 models. Subtract 1″ for access cab models
- Long bed models require the next step up in leaf spring, or they will sit 1″ less high. L59-110-R lift only 1″ on long bed models
- All lift heights are based on the baseline of 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. A 3″ front lift is 23″ for example. Some Tacoma’s come with 1″ lift from the factory
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Choose your desired suspension parts to build the kit best suited to your weight and desired lift height
- Multiple different leaf springs options to match up with the added weight you’ve put on your truck or not
- Choose from classic Twin Tube Shocks, IMS Monotube, or MRA 3-Way Adjustable Remote Resi Shocks
- Read this to learn about the shock differences – Shock Types
- Base kit usually starts with front coils, struts, rear leaf springs, poly bush kit, rear shocks, 1 pair greasable pins. You choose what you want
- Common installation instructions related to parts on this page
(12 reviews) -
80 Series Land Cruiser (1990-1997)FREE SHIPPING
within 48 US StatesDobinsons 0-3.5″ Lift Kit Builder | Toyota Land Cruiser 80 Series 1990-1997 (inc all shock options)
- Suits 1990 to 1997 Toyota Land Cruiser 80 Series and Lexus LX450
- Choose your coils and load carrying ability, anywhere from 0″ up to 3.5″ of Lift
- The more you lift, the more parts and pieces are needed for proper performance
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to match OE fitment specs
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- Choose from Twin Tube, IMS Monotube, or MRA 3-Way adjustable remote resi shocks
- Read down below about the 3 different shock types
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base kit includes front and rear coils and shocks, you can add any other parts you need
- Read more about the 3 different shock types
(13 reviews) -
4Runner 5th Gen (2010-2024)FREE SHIPPING
within 48 US StatesDobinsons 3-Way Adjustable MRR Toyota 4Runner Lift Kit | 2010-2024 (1-3.5″)
- Suits Toyota 4Runner 5th Gen 4×4 from 2010 to 2024
- If you have a 2WD model, add 1″ to the listed lift heights of the front coils due to the lighter front weight of the vehicle
-
The terms MRA and MRR are used interchangeably. The A stands for Adjustable in the part number or SKU
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Rear coil springs are optional in case you don’t want to lift the rear, and just lift the front
- Add up how much accessory weight you have on the front and then the rear, that’s your constant load
- Then choose the lift height from the coils that most closely matches the added weight
- Dobinsons have the largest selection of front and rear coils for 4Runners and in multiple colors
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Full 2 year limited warranty, no set rebuild time period
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- You can go from a standard suspension to full long travel with all the options listed here
- The more lift height you add, the more parts you need, so read the subsection headings below
- Lift heights are based on the standard 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. Many vehicles come in at different heights from the factory based on trim levels and options
- Resi Installation Installations of Front, and Rear
- Front height adjustment instructions
- Suspension Installation Video
(15 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons IMS Lift Kit for Toyota 4Runner 4×4 2003-2009 (0-3.5″)
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- For 2003-2009 Toyota 4Runner 4×4
- If you have a 2WD model, add 1″ to the listed lift heights of the front coils due to the lighter front weight of the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Shocks are Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Watch the video on IMS here: https://youtu.be/Npfx40VD3kM
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base Kit Price Includes 2 Front IMS Struts, 2 Rear IMS Shocks, and 4 Standard Coil Springs
- For information and specs on the products in the drop down lists below, select an item, then click the small square box that will appear to the right to be taken to that product page
(20 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons 3-Way Adjustable Toyota Tacoma MRR Lift Kit | 2005-23 (0-3.5″)
- 4×4 Access Cab models come with 1″ front lift from the factory. Lift heights listed are for Dual cab 4×4 models. Subtract 1″ for access cab models
- Long bed models require the next step up in leaf spring, or they will sit 1″ less high. L59-110-R lift only 1″ on long bed models
- All lift heights are based on the baseline of 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. A 3″ front lift is 23″ for example. Some Tacoma’s come with 1″ lift from the factory
-
The terms MRA and MRR are used interchangeably. The A stands for Adjustable in the part number or SKU
Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Dobinsons MRR front struts are height adjustable by a fully threaded body
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- Extended Travel Fronts – 567mm extended, 417mm compressed
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat up front
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes front vehicle-specific resi brackets, rear includes resi brackets that get mounted to the frame as shown in the photos
- Coilover adjuster wrench is included for the fronts
- Choose your desired suspension parts to build the kit best suited to your weight and desired lift height
- Multiple different leaf springs options to match up with the added weight you’ve put on your truck or not
- For installation instructions, click here
(11 reviews)
-
TJ Wrangler (1996-2006)FREE SHIPPING
within 48 US StatesKing 4WD Premium TJ Wrangler Soft Upper Door Windows Tinted 1996-2006
- Suits 1997-2006 Jeep Wrangler TJ 2-door soft top convertibles (and LJ Unlimited) with Factory Half Door and Soft Door Uppers
- Does not include any framework
- Includes left and right side windows
- Black Diamond Fabric with TINTED windows
- Black Diamond Fabric
- Specification: Two Layer 24oz Marine Grade – Waterproof
- Testing: CFFA, FMVSS & SAE Requirements
- Specification: UV Approved
- Testing: Accelerated Light Aging Test – 1000 Hours
- Window Glass
- Specification: 96g DOT Approved Pressed flexible vinyl, undistorted, won’t shrink or yellow
- Testing: CFFA, FMVSS & SAE Requirements
- Zippers
- Specification: Reinforced nylon self-correcting zippers
- Testing: 50,000 Cycle Test – No bind or drag
- Velcro
- Specification: Industrial Grade Fiber
- Testing: 150 kg (330 lbs.) per square inch
- Seams
- Specification: 135-gauge thread with heat sealed seams, 4-piece thread per inch
- Testing: CFFA, FMVSS & SAE Requirements
- Also available with Clear Windows (not tinted)
- We also sell a full soft top with replacement soft half door uppers as well, click for details
(7 reviews) -
Rear DrawersFREE SHIPPING
within 48 US StatesOVS Camp Kitchen Drawer With Slide Out Sink, Cooking Shelf and Work Station
- OVS Camp Kitchen Drawer is just like a cargo box that can be bolted down to your floor or on top of your base plate system
- Color: Black
- Slides: 3 Slides
- Lockable: Yes
- Mounting Rows: 3
- Mounting Holes: 18
- Body Material: Aircraft Grade Aluminum
- Hardware Material: Marine Grade Stainless Steel
- Securely Hold a Refrigerator: Yes
- Anchors Pins Included: Yes, QTY 4
- Tie Down Straps Included: Yes, QTY 4
- Cutting/Prep Board: Yes
- Food/Water Collapsible Sink: Yes
- Telescoping Poles: Yes, QTY 3
- Terrain Stabilizers Included: Yes, QTY 3
- BBQ Side Walls: Yes, and Reversible
(6 reviews) -
AwningsFREE SHIPPING
within 48 US StatesHD Nomadic Car-Side Shower Room
- Use this for a shower, use it for changing clothes, a quick change room, use it for a portable toilet enclosure, or whatever else you can think of!!
- Hide inside it and scare the crap out of your camping buddies when you’re out in the middle of nowhere!!
- Manufactured from a high performance 420D Oxford Rip Stop fabric and aluminum folding arms enclosed in rugged 1000D waterproof PVC integrated storage bag
- Mounts to roof rack with supplied L brackets and mounting stainless steel hardware
- This does NOT have a roof/ceiling, it is open at the top
- Quick and easy setup, simply unzip, fold out and stake down
- Curtain hems weighted with structural poles to keep shape – 42 Inch (L) X 42 Inch (W) X 76 Inch (H) with adjustable straps to accommodate various vehicle heights
- The front curtain wall features a heavy duty dual sided zip which allows easy access in and out of the Nomadic Car Side Shower
- Velcro strap to secure a shower head and two (2) internal pouches
- Download Instructions
(8 reviews) -
Air SolutionsFREE SHIPPING
within 48 US States4 Piece Adjustable Tire Deflator Kit – 10-30 PSI
- Adjustable Pre-Set From 10-30 PSI
- Easy Twist Adjustable Design
- Super Slim Design to fit into aftermarket wheels easier
- Compact and Precise
- Deflators will automatically Stop at the Preset PSI
- Includes Storage Bag
- Kit of 4, you can deflate 4 tires at the same time
(13 reviews) -
AwningsFREE SHIPPING
within 48 US StatesOverland Vehicle Systems Nomadic 180° Awning – Dark Gray With Black Bag
Features:
- 88 Square Feet of Freestanding Covered Shelter
- 600D Poly Cotton Rip-Stop Cover
- Boxed Aluminum Rafters
- Pivoting Aluminum Adjustable Poles
- Tie Down Points for Securing Poles and Water Run Off
- 1000G PVC Travel Cover
- 10 Lb Zipper
- Ballistic Nylon Tie Downs With S Connects and Buckle
- Shock Cord With Retention
- Zippers To Secure Enclosed Shelter
- Heavy Duty Oversized Stakes
- Can mount to driver or passenger side of vehicle
What’s included:
- 180 Degree Awning With 4 Built-In Aluminum Rafters
- 3 Pivoting and Telescoping Aluminum Poles + 2 Telescoping Aluminum Poles
- 4 Sets of Shock Cord
- 4 Heavy Duty Stakes
- Travel Cover
- 3 Heavy Duty Mounting Brackets and Hardware
- Nylon Reinforced Tie Down Kit
- Opened: 240 x 78.5 Inch
- Closed: 88 x 7 x 6 Inch
- Download Instructions
(8 reviews) -
Sale!RecoveryFREE SHIPPING
within 48 US StatesOVS Tow Strap 30,000 lb. 3″ x 30′ Gray With Black Ends & Storage Bag
Construction
- Manufactured out heavy duty synthetic fiber with a 30,000 lb. breaking strength
- 30 foot long 3 inch wide folded and double stitched end with a heavy-duty padded protective sleeve
- Loop size is 10 inch which is ideal for all types of rigging including soft shackles and D Rings
- Tightly woven 30 strands per inch reinforced synthetic fiber material for extra durability
- Soft and pliable material flexes easy with no stretch and is ideal for static recovery situations
- Included storage bag with mesh at the bottom that allows dirt and debris to escape
Functions
- Ideal for daisy chaining vehicles through tough obstacles or long pulls with inoperable vehicle
- Can be used as a winch extension when extra length is needed
- Clean all mud and sand off of all synthetic ropes and straps as soon as you get home. Sand granules have sharp edges that can cut into the fibers at the microscopic level reducing the safe load rating
(8 reviews) -
Sale!RecoveryFREE SHIPPING
within 48 US StatesOverland Vehicle Systems Tire Repair Kit – 53 Piece Kit With Black Storage Box
- Over-sized T Style Handle Reamer and Probe
- 53 Piece
- Self-Vulcanized Plugs
- Extended Heavy-Duty Needle Nose Pliers
- Pencil Style Dual Pressure Gauge and Dual Chuck
- Valve Repair Kit Which Includes Valve Cores
- Plastic and Chrome Valve Caps
- Tire Deflators and 4 Way Valve Tool Kit
(3 reviews) -
ExcludedFREE SHIPPING
within 48 US StatesExpedition Truck Cap Crossbars | 3 Sizes
- Designed to work with OVS Expedition Caps
- Cross bars are compatible with most roof rack accessories
- Ideal for mounting tents, awnings, shower tents, storage boxes, kayaks, skis, and more
- Removable end caps for easy access to T-slot attachments
- Weatherproof design resists rust and corrosion
- Sturdy aluminum construction supports up to 325 lbs dynamic and 750 lbs static with OVS Expedition Caps
- Aerodynamic, low-profile 2.75” design reduces wind noise
- Sleek, finished look with end caps
- Includes risers and all necessary hardware for easy installation
- Sold in pairs
- Available in 3 width sizes: 51.25”, 55”, and 72”
(0 reviews)
-
4Runner 5th Gen (2010-2024)FREE SHIPPING
within 48 US StatesDobinsons Toyota 4Runner IMS Suspension Kit for 2010-24 (1-3.5″)
- Suits Toyota 4Runner 5th Gen 4×4 from 2010 to 2024, with or without KDSS
- If you have a 2WD model, add 1″ to the listed lift heights of the front coils due to the lighter front weight of the vehicle
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Rear coil springs are optional in case you don’t want to lift the rear, and just lift the front
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Dobinsons have the largest selection of front and rear coils for 4Runners and in multiple colors
- Add up how much accessory weight you have on the front and then the rear, that’s your constant load
- Then choose the lift height from the coils that most closely matches the added weight
- Fully rebuildable and re-valvable shocks and struts
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Option to have the front struts preassembled prior to shipping to make installation easier at home
- Base Kit Includes 2 Front IMS Monotube Struts, 2 Rear IMS Monotube Shocks, and 4 Coil Springs – Select your preferences
- You can go from a standard suspension to full long travel with all the options listed here
- The more lift height you add, the more parts you need, so read the subsection headings below
- Lift heights are based on the standard 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. Many vehicles come in at different heights from the factory based on trim levels and options
- Suspension Installation Video
(23 reviews) -
Dobinsons
Dobinsons 0-3″ Extended Travel IMS Tacoma Coilovers | 2005-2023
- Suits 2005-2023 Toyota Tacoma 4×4 Models
- Looking for a quick and easy way to lift your Tacoma? This is your answer
- Select your desired lift height and spring rate – we’ll take care of the rest!!
- All lift heights are based on the baseline of 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. A 3″ front lift is 23″ for example. Some Tacoma’s come with 1″ lift from the factory
- Dobinsons IMS are height adjustable by a fully threaded body
- The Dobinsons IMS Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- Extended Travel – 567mm extended, 417mm compressed
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Includes the tool to adjust the coil seat height
- Instructions for setting coil seat height
- Note about lift heights – all vehicles can have some variance and desired lift height may need to be adjusted to suit your specific vehicle. Adding 2.5″ or more lift, new UCA’s should be added for proper articulation and correct wheel alignment
- Click to see Matching rear shocks
- Please NOTE: Assembled coilovers cannot be returned, as they are made to order
(18 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons 3-Way Adjustable Toyota Tacoma MRR Lift Kit | 2005-23 (0-3.5″)
- 4×4 Access Cab models come with 1″ front lift from the factory. Lift heights listed are for Dual cab 4×4 models. Subtract 1″ for access cab models
- Long bed models require the next step up in leaf spring, or they will sit 1″ less high. L59-110-R lift only 1″ on long bed models
- All lift heights are based on the baseline of 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. A 3″ front lift is 23″ for example. Some Tacoma’s come with 1″ lift from the factory
-
The terms MRA and MRR are used interchangeably. The A stands for Adjustable in the part number or SKU
Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Dobinsons MRR front struts are height adjustable by a fully threaded body
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- Extended Travel Fronts – 567mm extended, 417mm compressed
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat up front
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes front vehicle-specific resi brackets, rear includes resi brackets that get mounted to the frame as shown in the photos
- Coilover adjuster wrench is included for the fronts
- Choose your desired suspension parts to build the kit best suited to your weight and desired lift height
- Multiple different leaf springs options to match up with the added weight you’ve put on your truck or not
- For installation instructions, click here
(11 reviews) -
Full Suspension Kits - 5th Gen 4Runner
Dobinsons 2-3.5″ Extended Travel Pre-Assembled IMS Coilovers | Toyota 4Runner 2010-2024
- Suits 2010-2024 Toyota 4Runner 5th Gen 4×4 Models
- Looking for a quick and easy way to lift your 4Runner? This is your answer
- A 4×2 model lifts 1″ extra with the 4×4 lift heights
- Select your desired lift height and spring rate – we’ll take care of the rest!!
- Dobinsons IMS are height adjustable by a fully threaded body
- The Dobinsons IMS Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- Extended Travel – 575mm fully extended, 430mm compressed
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
- Instructions for setting coil seat height
- To run these Extended Travel coilovers, new UCA’s need to be added for proper articulation and correct wheel alignment. A diff drop kit is also recommended to minimize CV binding at full droop
- Click to see Matching rear shocks
- Please NOTE: Assembled coilovers cannot be returned, as they are made to order
- Lift heights are based on the standard 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. Many vehicles come in at different heights from the factory based on trim levels and options
(5 reviews)
Latest News
April 28, 2025
Product InfoNoisy Coil Springs? Try Adding this
Have you upgraded your suspension and are noticing a noise coming [...]
April 22, 2025
NewsDobinsons Price Increase – May 1st 2025
Unfortunately we have just received the news that Dobinsons Spring [...]
April 15, 2025
Product InfoDobinsons Billet Adjustable Rear Lower Control Arms Pair
Finally, an awesome adjustable rear lower control arm option for your [...]
February 26, 2025
Product InfoLongfield Super Axles: The Ultimate IFS Axle Set for 2024+ Toyota Land Cruiser 250 Series and Prado 250
Are you an adventurer seeking the toughest axle set for your Toyota [...]
Fast Delivery
USA, Hawaii, Alaska, Puerto Rico, Guam, Canada
Expert advice
Reach out if you need help, we are here to help you!
MULTIPLE PAY OPTIONS
We offer financing, Paypal, Cards, Venmo
gift purchase?
Your wife doesn't need to know!!