Your cart is currently empty!
Dobinsons JL JT Adjustable Front Lower Arms Pair | JL Wrangler Gladiator JT
- Suits Jeep JL Wrangler 2018+ 2 door and 4door models and Jeep Gladiator JT 2020+
- Comes with highly flexible rubber bushings installed
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Oversized adjusters and rod thickness for maximum strength and durability with double-nut locking feature
- Zinc plated, then powder coated black, for the ultimate finish and protection
- More details and installation instructions are down below
$405.00
In Stock
SKU: WA29-558K
Categories: Control Arms, Control Arms - Gladiator, Control Arms - JL Wrangler, Dobinsons, Gladiator JT (2020-2024+), JL Wrangler (2018-2024+), Lower Control Arms, Suspension
Brand: Dobinsons Spring & Suspension
Description
Dobinsons JL JT Adjustable Front Lower Arms Details
Dobinsons JL JT Adjustable Front Lower Arms for Jeep JL Wrangler 2018+ 2-door and 4-door and Jeep Gladiator JT 2020+ – These are adjustable front Jeep JL and JT lower control arms, to be used on any JEEP lifted or not, up to 3″ of lift. This kit comes with both side lower arms and also includes Rubber bushings pressed into the Dobinsons WA29-558K arms, as they are maintenance and noise-free. Rubber bushings allow for greater flex (travel). These adjustable arms will allow you to properly set your caster angle due to adding a lift, while also adding strength over the stock arms. Suitable also for long travel rear suspension setups.
NOTE: The Dobinsons JL JT Adjustable Front Lower Arms threaded end goes towards the frame end, and the curved section of the arm faces towards the frame, to maximize tire clearance when turning. This angled position provides additional tire scrub radius clearance, which is extremely important on 35″ or 37″ tires, as they will hit the stock arms too easily, damaging your tires and potentially damaging other parts as well.
Instructions for use: Set the initial length of the Dobinsons Adjustable Front Lower Arms to the same as factory arms, then add 1/2″ or so to the overall length. Install, then check the caster angle, then add at 1/4″ increments until your caster angle is set properly. Adding too much length could lead to driveline vibrations. It’s recommended to use blue Loctite under each of the nuts once they are in their final adjusted position to keep them in place. Excessive flexing without the front sway bar connected can loosen them up otherwise.
Dobinsons heavy duty front control arms are the some of the most affordable on the market, while adding necessary strength to the front end. The last thing you want when you offroad a lot is a bent arm, as this affects your alignment and your vehicle will not track straight down the road. With 5mm thick wall tubing, you can’t go wrong with a set of these.
To see all Dobinsons control arms, click here:Â https://exitoffroad.com/product-category/suspension/control-arms/
The construction and adjustment of this part is exactly like the Dobinsons Panhard rods, as shown in this video here:
Vehicle Fitment:
2018 Jeep Wrangler
2019 Jeep Wrangler
2020 Jeep Wrangler
2021 Jeep Wrangler
2022 Jeep Wrangler
2023 Jeep Wrangler
2024 Jeep Wrangler
2019 Jeep Wrangler
2020 Jeep Wrangler
2021 Jeep Wrangler
2022 Jeep Wrangler
2023 Jeep Wrangler
2024 Jeep Wrangler
2020 Jeep Gladiator
2021 Jeep Gladiator
2022 Jeep Gladiator
2023 Jeep Gladiator
2024 Jeep Gladiator
2021 Jeep Gladiator
2022 Jeep Gladiator
2023 Jeep Gladiator
2024 Jeep Gladiator
4 reviews for Dobinsons JL JT Adjustable Front Lower Arms Pair | JL Wrangler Gladiator JT
You must be logged in to post a review.
Related products
-
Tacoma 3rd Gen (2016-2023)
Dobinsons 0-3″ Lift Kit Toyota Tacoma 2016-2023 with Blocks or AAL
- 4×4 Access Cab models come with 1″ front lift from the factory. Lift heights listed are for Dual cab 4×4 models. Subtract 1″ for access cab models
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Normal kit Includes 2 Front Struts, 2 Rear Shocks, 2 Front Coil Springs (a pair), Rear Spacer Blocks and U-Bolts
- You can now select to use Wheeler’s Add-A-Leaf Kit instead of the Quick Ride Kit if you’d prefer
- For rear lift, choose either the Quick Ride Kit or an Add-A-Leaf kit
- Select desired lift height and additional options
(13 reviews) -
ExceptionsFREE SHIPPING
within 48 US StatesETA is late DecemberDobinsons Tubular UCA Pair | 4Runner FJ Cruiser GX470 GX460
- Suits Toyota 4Runner 4th and 5th Gen 2003-2024, FJ Cruiser all years, Lexus GX470 and GX460
- Complete ASSEMBLED kit for both left and right hand side, includes new ball joints OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Has more clearance around the ball joint than factory UCA’s for better tire clearance
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height, as factory alignment correction will be enhanced with these
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Curved washers face outwards away from bushings during installation, per the product video
- Product Video
- Includes left and right assembled arms, ball joint caps, and hardware to mount ABS lines
- Also sold without ball joints
- Replacement Ball Joints can be ordered here
(8 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesETA is late DecemberDobinsons Tubular UCA Pair | Tacoma Hilux Fortuner 2005-23
- Suits Toyota Tacoma from 2005 to 2023, Toyota Hilux Vigo and Revo from 2005+, and Toyota Fortuner 2005 to 2023
- Complete assembled kit for both left and right hand side, includes new ball joints, ball joint caps, OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Has more clearance around the ball joint than factory UCA’s for better tire clearance
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height of 1.5″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Product Video
- Also sold without ball joints
- Replacement Ball Joints can be ordered Here
(9 reviews) -
80 Series Land Cruiser (1990-1997)
Dobinsons 80 Series Stock Height Restoration Suspension Kit (inc all shock options)
- Suits Land Cruiser 80 Series and Lexus LX450
- Restore your vehicle back to the original ride height, and bring the ride quality way up at the same time with the Dobinsons 80 Series Stock Height Suspension Kit
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to match OE spec and height
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Includes 2 Front Shocks, 2 Rear Shocks, and 4 Coil Springs. Add on additional parts if desired
(18 reviews)
Joseph (verified owner) –
Value for money, super satisfied.
Shawn (verified owner) –
Exit Offroad really does know what they’re talking about, they have the best product pages.
Shawn (verified owner) –
Exit Offroad really does know what they’re talking about, they have the best product pages.
Michael (verified owner) –
*****