Your cart is currently empty!
KDSS Spacer Kit – Lexus GX460 5th Gen 4Runner by Treaty Oak Offroad
- Suits 5th Gen Toyota 4Runner with KDSS (2010-2024) and Lexus GX460 (2010-2023)
- Made from 6061 aluminum, Type III hard coat anodized in black, and supplied with new hardware
- May require modification to your factory front skid plates due to additional down travel of the sway bar
- Helps correct incessant lean of a lifted vehicle with KDSS by adding a spacer to the fixed mount up front and to both mounts on the rear
- Bolt on installation – may require trimming of OE skid plate on passenger side to add more clearance
- Mounts between factory points that hold the sway bar in place
- Raised/longer spacers helps correct the lean of a vehicle and also adds additional rear travel in the back to help clear the sway bar link from the panhard rod at full extension
- Includes front and rear mounts (3 in total)
- See instructional video for how these get installed here
- Installation Instructions
$200.00
In StockDescription
KDSS Spacer Kit – Lexus GX460 5th Gen 4Runner by Treaty Oak Offroad, for a great solution to an annoying problem on lifted Lexus and Toyota SUV’s.
- KDSS Spacer Kit Made from 6061 aluminum, Type III hard coat anodized in black, and supplied with new hardware
- May require modification to your factory front skid plates due to additional down travel of the sway bar
- KDSS Spacer Kit Helps correct incessant lean of a lifted vehicle with KDSS by adding a spacer to the fixed mount up front and to both mounts on the rear
- KDSS Spacer Kit is a Bolt-on installation
- Mounts between factory points that hold the sway bar in place
- Raised/longer spacers helps correct the lean of a vehicle and also adds additional rear travel in the back to help clear the sway bar link from the panhard rod at full extension
- Installation Instructions
If you’re lifted, and have wheeled, you have undoubtedly encountered some kdss lean. In the 4 years of working with my 2005 GX470 sport with kdss, I have run into this issue multiple times, and developed this kit to run extended travel rear shocks and help combat kdss lean. The same applies to the Lexus GX460 and Toyota 4Runner 5th Gen
WHY DOES THIS HAPPEN?!
▪️KDSS is a complete system front and rear, that works in tandem. The driver side has an articulating cylinder and the passenger side has a rigid link, connected to the LCA (or axle in rear) via a large sway bar. They work together via hydraulic lines and accumulators that open and close to allow fluid to flow, or not flow, depending on speed. On a stock vehicle this allows for extended wheel travel vs a standard sway bar setup AND sports car type handling at speed.
▪️When your vehicle is lifted, the cylinder extends as the vehicle is raised, but the passenger side can’t due to that rigid link. This is what causes your lean.
What we developed, will equalize the pressure in the system via a set of spacers (1 in front, 2 in rear) that are utilized within the KDSS system itself and return the angle of the sway bar back to OEM angles after a lift has been installed. In turn, this will dramatically reduce or eliminate your lean.
These are 6061 aluminum, type III hard coat anodized in black, and supplied with new hardware..
*This may require modification to your factory skid plates
*While we have had fantastic results reducing and eliminating lean, due to the nature of the KDSS system it is still possible to experience some lean. A proper KDSS balance and the use of our spacers are the best option for maximizing wheel travel, while minimizing lean.
Related products
-
ExceptionsShips FREE !!
within 48 US StatesETA is July 2024Dobinsons Tubular UCA Kit | 4Runner FJ Cruiser GX470 GX460
- Suits Toyota 4Runner 4th and 5th Gen 2003-2024, FJ Cruiser all years, Lexus GX470 and GX460
- Complete ASSEMBLED kit for both left and right hand side, includes new ball joints OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height, as factory alignment correction will be enhanced with these
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Curved washers face outwards away from bushings during installation, per the product video
- Product Video
- Includes left and right assembled arms, ball joint caps, and hardware to mount ABS lines
- Also sold without ball joints
$795.00 Add to cart -
GX460 (2010-2023)
Dobinsons 1.5-3.5″ Lift Kit for Lexus GX460 2010 to 2023 (all options)
- Every suspension option from Dobinsons to lift your Lexus GX460 all on one page
- Here you can lift from a low height up to the maximum bolt-on lift height by making your selections below
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base Kit Includes 2 Front Twin Tube Struts, 2 Rear Twin Tube Shocks, and 4 Coil Springs
- You can choose to upgrade to the higher end IMS or MRA struts and shocks on this page in the drop down menus
From $1,200.00 Select options -
ExceptionsShips FREE !!
within 48 US StatesETA is Summer 2024Dobinsons MRA59-A220 3-Way Adjustable MRA Front Struts Extended Travel
- Suits 2003-2009 4th Gen 4Runner, 2006-2009 FJ Cruiser, 2005-2023 Tacoma (2nd and 3rd Gen Tacoma), Lexus GX470, Toyota Prado 120, and 2005-2015 Toyota Hilux Vigo
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- Extended Travel – 567mm extended, 417mm compressed
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Bolt-on Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Resi brackets bolt in between the stock front sway bar mount
- Full 2 year limited warranty, no set rebuild time period
- Does not include coil springs or top mounts – sold separately
- Instructions for setting coil seat height
- Resi installation instructions
$1,280.00 Add to cart -
Dobinsons
Dobinsons C59-221V Stock Height Rear Coil Springs | Land Cruiser 80 series
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- 460/470mm free height, 17mm wire, variable rate
- Sold in Pairs
$270.00 Add to cart