Your cart is currently empty!
Skid Plates + Sliders - Bronco 2021+
Showing all 6 resultsSorted by popularity
-
Bronco (2021-2024+)On Sale All November!!
RCI Bronco Gas Tank Skid Plate | Ford Bronco 4-Door 2021+
- Suits 2021+ Ford Bronco 4-Door
- Smooth, flat surface that easily slides over obstacles
- Black powder coat available for rust resistant, durable and high quality finish
- Simple bolt on installation
- All hardware and instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling
(2 reviews) -
Bronco (2021-2024+)On Sale All November!!
RCI Rear Bronco Diff Skid Plate | 2021+ Ford Bronco
- Suits 2021+ Ford Bronco
- Protects the low hanging rear differential
- Clamps directly to axle housing for an easy no drill install
- Hugs differential tightly, within 1/4″ for minimal loss in ground clearance.
- Black powder coated for rust resistant, durable and high quality finish
- Design incorporates drain holes for water and dirt to escape, as well as allow full access to the differential drain plug
- Installs in minutes
- All hardware and installation instructions provided
- MADE IN THE USA
(5 reviews) -
Bronco (2021-2024+)On Sale All November!!
RCI Full Skid Plate Package | 2021+ Ford Bronco 2/4 Door
- Suits 2021+ Ford Bronco 2 door and 4 door models – Does not suit Bronco Sport models
- Includes engine (two piece), transmission and transfer-case skid plates.
- Protects expensive EPAS power steering unit, front differential, front cross-member, engine, engine bay, intercooler, sway bar disconnect (if applicable),, transmission, exhaust, oil pan, transfer-case, and more!
- Compatible with 4×4 and Raptor models
- Simple installation and removal of all subsections for maintenance
- Extremely high clearance hugs the truck very tight and does not sacrifice ground clearance for protection
- Smooth, flat surface that easily slides over obstacles
- Steel version-black epoxy powder coated for rust resistant, durable and high quality finish
- Installs in minutes
- All hardware and installation instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- *May Not be Compatible with all 4+” Lift Kits (drop bracket kits)
- Made in the USA
(9 reviews) -
Bronco (2021-2024+)FREE SHIPPING
within 48 US StatesARB 5480100 Skid Plate Kit | Ford Bronco 4-Door 2021+
- Ford Bronco Skid Plate Set, Suits Ford Bronco 2021+ 4-Door Models
- 3mm pressed and folded sheet steel adds more strength than a standard folded sheet.
- Laser cut sheet steel.
- Zinc plated and powder coated with a silver textured finish.
- Recessed mounting bolts are protected and easy to remove for vehicle servicing.
- The Under Vehicle Protection will fit with or without an ARB front bumper. Fitment has not been confirmed with other aftermarket bumper designs
- Comprises 4 panels: Front Panel (Protects power steering, engine sump, sway bar), Diff Panel (Protects front diff mounts, engine sump), Transmission (Protects transmission and transmission controls) and Transfer Case (Protects transfer case)
- See more details below as well as product video
(6 reviews) -
Bronco (2021-2024+)
Ford Bronco Diff Cover by ARB | 2021+
- Suits 2021+ Ford Bronco 2-door and 4-door models with Dana 44 Rear Axle
- High-tensile nodular iron structure protects differential and ring and pinion set from obstacles
- Computer-optimized, cross-brace design within the differential cover increases the structural rigidity of the axle acting as a truss
- Approach/departure angle optimized by angled exterior surface
- Prolonged carrier bearing life due to extra support to the bearing alignment
- Additional housing strength helps keep the ring and pinion gears meshing on the flat faces of the teeth, extending ring and pinion life and overall maximum load strength
- Magnet in the end of the dipstick allows the oil to be checked for tell-tale signs of internal damage without removing the cover or draining the oil
- Low profile drain plug design resists damage from obstacles
- Combination of the high-filler point and dipstick allows the oil to be checked for water contamination without having to drain the oil
- Unique dipstick/filler cap design allows differential oil level to be adjusted for customized high driveline angles
- Cover is powder coated, CNC machined, and clear-coated for a durable, professional, long-lasting finish; all hardware is hardened and plated
- Tensile-cap screws (supplied) are recessed for protection against obstacles which might damage or loosen the screws
- Made in Red or Black, choose below
(3 reviews)