Your cart is currently empty!
4Runner 5th Gen (2010-2024)
Showing 151–180 of 203 resultsSorted by popularity
-
ARBOME 2895E Rear Coil Springs | 4Runner FJ Cruiser GX470 GX460 – Pair
- OME Part Number 2895E
- Bar Size : 17 mm
- Free Height : 375mm
- Number of Turns : 6.75
- Coil Weight (each): 5.4 Kg | 11.9 lbs
- Spring Rate : 260 lbs
- Sold in Pairs
(9 reviews) -
ARB
OME 2884 Front Coil Springs | Toyota Lexus Trucks SUV’s – Pair
- OME Part Number 2884
- Bar Size : 16.5mm
- Free Height : 390mm
- Number of Turns : 9.75
- Coil Weight (each): 4.7 Kg | 10.3 lbs
- Spring Rate : 590 lbs
- Sold in Pairs
- These are NOT COMPATIBLE with the newer MT64 struts from Old Man Emu – They don’t fit
(13 reviews) -
Differential | DrivetrainFREE SHIPPING
within 48 US StatesARB RD121 Front Air Locker Toyota Lexus 8″ IFS 30 Spline 3.73-
- For Use With Toyota 8″ IFS Clamshell differential with 30 Spline Axles and 3.73 And Down Factory Gears
- Usually all models that came with a manual transmission used 3.73- factory gear ratios, but you must check before ordering
- Factory R&P may use either RD111 or RD121 depending on ratio. All known aftermarket R&P sets suit RD121.
- If you are re-gearing, check with the gear manufacturer for which Air Locker to order
- Full vehicle fitment list is further down in the main description, includes 4Runner, Tacoma, FJ Cruiser, GX470, GX460
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
(12 reviews) -
Skid PlatesFREE SHIPPING
within 48 US StatesARB 5421110 Under Vehicle Protection Kit | Toyota 4Runner 5th Gen (with KDSS)
- Suits all Toyota 4Runner 5th Gen models from 2010 to 2024 WITH KDSS
- You must check to make sure you have KDSS before ordering this kit
- 3mm pressed and folded sheet steel adds more strength than a standard folded sheet.
- Laser cut sheet steel.
- Zinc plated and powder coated with a silver textured finish.
- Recessed mounting bolts are protected and easy to remove for vehicle servicing.
- The Under Vehicle Protection will fit with or without an ARB front bumper. Fitment has not been confirmed with other aftermarket bumper designs
- Comprises 4 panels: Front Panel (Protects power steering, engine sump, sway bar), Diff Panel (Protects front diff mounts, engine sump), Transmission (Protects transmission and transmission controls) and Transfer Case (Protects transfer case)
- See more details below as well as product video
(9 reviews) -
Trail-Gear
Longfield IFS +3.5″ CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- +3.5″ length for use on +3.5″ long travel kits (cannot be used with stock lower control arms)
- Longfield IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- 35-spline CV Joint stars & axle shafts.
- Available in direct stock replacement versions & long-travel versions.
- CV Joints housings are 100% SAE 4340 Chromoly Steel.
- Double-offset inboard CV joint with 1-inch diameter all bearings.
- SAE 4340 Chromoly Steel axle shafts with black powder-coat finish.
- 300M internal components.
- Proprietary elastomer boot material for enhanced puncture & tear resistance.
- Wear-Resistant 52100 Alloy Steel Bearing Balls.
- All Components Precision Polished to Remove Imperfections and Prevent Stress Risers.
- CV Joints Black Oxide & Powder-Coat Finish for Corrosion Resistance.
- CV Joints are pre-lubricated with racing-grade Red Line CV-2 Moly Grease
- Includes IFS axle spindle nuts.
- Sold as a pair
- Made in the USA
- Installation Guide
(0 reviews) -
Trail-Gear
Longfield IFS +2.75″ CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- +2.75″ length for use on +2.75″ long travel kits (cannot be used with stock lower control arms)
- Longfield IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- 35-spline CV Joint stars & axle shafts.
- Available in direct stock replacement versions & long-travel versions.
- CV Joints housings are 100% SAE 4340 Chromoly Steel.
- Double-offset inboard CV joint with 1-inch diameter all bearings.
- SAE 4340 Chromoly Steel axle shafts with black powder-coat finish.
- 300M internal components.
- Proprietary elastomer boot material for enhanced puncture & tear resistance.
- Wear-Resistant 52100 Alloy Steel Bearing Balls.
- All Components Precision Polished to Remove Imperfections and Prevent Stress Risers.
- CV Joints Black Oxide & Powder-Coat Finish for Corrosion Resistance.
- CV Joints are pre-lubricated with racing-grade Red Line CV-2 Moly Grease
- Includes IFS axle spindle nuts.
- Sold as a pair
- Made in the USA
- Installation Guide
(0 reviews) -
Trail-Gear
Longfield IFS +2.00″ CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- +2.00″ length for use on +2.00″ long travel kits (cannot be used with stock lower control arms)
- Longfield IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- 35-spline CV Joint stars & axle shafts.
- Available in direct stock replacement versions & long-travel versions.
- CV Joints housings are 100% SAE 4340 Chromoly Steel.
- Double-offset inboard CV joint with 1-inch diameter all bearings.
- SAE 4340 Chromoly Steel axle shafts with black powder-coat finish.
- 300M internal components.
- Proprietary elastomer boot material for enhanced puncture & tear resistance.
- Wear-Resistant 52100 Alloy Steel Bearing Balls.
- All Components Precision Polished to Remove Imperfections and Prevent Stress Risers.
- CV Joints Black Oxide & Powder-Coat Finish for Corrosion Resistance.
- CV Joints are pre-lubricated with racing-grade Red Line CV-2 Moly Grease
- Includes IFS axle spindle nuts.
- Sold as a pair
- Made in the USA
- Installation Guide
(0 reviews) -
Trail-Gear
Longfield IFS CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- Standard/Stock length for use on lifted and non-lifted applications
- Longfield IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- 35-spline CV Joint stars & axle shafts.
- Available in direct stock replacement versions & long-travel versions.
- CV Joints housings are 100% SAE 4340 Chromoly Steel.
- Double-offset inboard CV joint with 1-inch diameter all bearings.
- SAE 4340 Chromoly Steel axle shafts with black powder-coat finish.
- 300M internal components.
- Proprietary elastomer boot material for enhanced puncture & tear resistance.
- Wear-Resistant 52100 Alloy Steel Bearing Balls.
- All Components Precision Polished to Remove Imperfections and Prevent Stress Risers.
- CV Joints Black Oxide & Powder-Coat Finish for Corrosion Resistance.
- CV Joints are pre-lubricated with racing-grade Red Line CV-2 Moly Grease
- Includes IFS axle spindle nuts.
- Sold as a pair
- Made in the USA
- Installation Guide
(0 reviews) -
Steering Upgrades
Power Flow Land Cruiser 200 Series Steering Rack – All New
- Direct replacement for Toyota OEM Part Number 44200-60170 for Land Cruiser 200 Series and Lexus LX570 5.7L V8 2008-2021
- High-quality LC200 OEM-style Replacement
- Brand New Rack, NOT rebuilt
- No core charge and no return shipping of the old unit required
- Largest & strongest Toyota-size steering rack
- Has 3rd rack mount that Tacoma or Tundra racks do not have.
- High-temperature seals
- M22-1.5 Threaded Tie Rod ends
- Can be used as an OEM replacement or as part of the All Pro +3.50″ Modular Long Travel Kit or similar
- Adaptation is required for this to fit Tacoma, 4Runner, GX470, GX460 and FJ Cruiser – that adaptation comes with the long travel kit (sold separately)
- Includes only what is in the photos
(0 reviews) -
Apache Offroad
Apache Offroad AX2 IFP Rear Long Travel Shocks Pair | 4Runner FJ GX470 GX460
- Suits 2003-2024 4Runner (4th and 5th Gen), All FJ Cruisers, Lexus GX470 and GX460, Toyota Prado 120 & 150, suitable for 2.5-3.5″ of lift – LONG TRAVEL
- REQUIRES THE USE OF DOBINSONS OR APACHE LONG TRAVEL REAR COILS, regular coils will simply fall out
- REQUIRES EXTENDED REAR CENTER BRAKE LINES
- REQUIRES EITHER APACHE BUMP STOP EXTENSIONS OR DUROBUMPS 5.25″ BUMP STOP REPLACEMENTS. SPACER MUST BE USED WITH TIMBREN OR OTHER BRAND BUMPS
- IF EQUIPPED – KDSS – We have ran LT rear on KDSS trucks, without issue, though it will limit your travel without additional modification.
- Direct Bolt on Installation
- Includes upper bushings and washers, and lower bushings already pressed in
- Includes shock boots to protect the shock shaft
- Proprietary high-Zinc content paint coating for superior protection against rock chips and abrasion damage
- Nitrogen Charged Monotube Design
- Internal Floating Piston- Separates the oil and nitrogen to prevent shock fade
- Fully rebuildable and revalveable
- Linear Valving
- Hardened Chrome Piston shaft- resists rock damage and corrosion
- Precision Japanese CNC machined, High Flow Piston
- Heavy Duty Ultra Low Friction Japanese 3 Stage Seal System
- High Quality German Oil
- Heavy Duty Lower Leg
- Hardened Rubber Lower Bushing provides a long and quiet life
- Heavy Duty 1/8″ (3mm) DOM wall thickness
- 2 Year Warranty
- 438mm Compressed, 720mm Extended
- SOLD IN PAIRS – Includes new washers and bushings for the top, and lower bushings are pressed in
(10 reviews) -
Apache Offroad
Apache Offroad AX2 IFP Rear Shocks Pair | 4Runner FJ GX470 GX460
- Suits 2003-2024 4Runner (4th and 5th Gen), All FJ Cruisers, Lexus GX470 and GX460, Toyota Prado 120 & 150, suitable for 0 – 3″ of lift
- Direct Bolt on Installation
- Includes upper bushings and washers, and lower bushings already pressed in
- Includes shock boots to protect the shock shaft
- Proprietary high-Zinc content paint coating for superior protection against rock chips and abrasion damage
- Nitrogen Charged Monotube Design
- Internal Floating Piston- Separates the oil and nitrogen to prevent shock fade
- Fully rebuildable and revalveable
- Linear Valving
- Hardened Chrome Piston shaft- resists rock damage and corrosion
- Precision Japanese CNC machined, High Flow Piston
- Heavy Duty Ultra Low Friction Japanese 3 Stage Seal System
- High Quality German Oil
- Heavy Duty Lower Leg
- Hardened Rubber Lower Bushing provides a long and quiet life
- Heavy Duty 1/8″ (3mm) DOM wall thickness
- 2 Year Warranty
- 385mm Compressed, 610mm Extended
- SOLD IN PAIRS – Includes new washers and bushings for the top, and lower bushings are pressed in
(10 reviews) -
Apache Offroad
Apache Offroad AX2 IFP Struts Pair | 2010+ 4Runner FJ Cruiser GX460
- Suits 2010-2024 4Runner, 2010+ FJ Cruiser, Lexus GX460, suitable for 0 – 3.5″ of lift
- 3 Spring seat settings: OEM height 0″ (213mm), +1″ (226mm), and +1.5″ (231mm)
- Use with OEM coils for a mild lift by preloading, or run lifted coils like Dobinsons
- Direct Bolt on Installation
- Proprietary high-Zinc content paint coating for superior protection against rock chips and abrasion damage
- Nitrogen Charged Monotube 2.2″ Body Design
- Internal Floating Piston- Separates the oil and nitrogen to prevent shock fade
- Fully rebuildable and revalvable
- Linear Valving
- Hardened Chrome Piston shaft- resists rock damage and corrosion
- Precision Japanese CNC machined, High Flow 50mm Piston
- Heavy Duty Ultra Low Friction Japanese 3 Stage Seal System
- High Quality German Oil
- Heavy Duty Lower Leg
- Hardened Rubber Lower Bushing provides a long an quiet life
- T6 6061 Aluminum Spring Seat
- Heavy Duty Spring Seat Circlip
- Heavy Duty 1/8″ (3mm) DOM wall thickness
- Down travel Spacer (under top hat spacer shaft spacer/extender) to provide adequate down travel for lift heights of 3-3.5″- Eliminates the need to rebuy extended travel struts when making changes to taller lift heights. Ideal for those who change their lift height overtime. Works by extending the point at which the upper washer sits on the shaft, thus raising the mounting position of the top hat and increasing down travel. Use for lifts 3-3.5″
- Works from 0-3.5″ of lift
- 2 Year Manufacturer’s Warranty
- No set rebuild periods
- 430mm Compressed, 560 mm Extended without DT Spacer, 575mm Extended with DT Spacer
- SOLD IN PAIRS – Includes new washers and bushings for the top, and lower bushings are pressed in
(10 reviews) -
Upper Control Arms
SPC 35102 Replacement Ball Joint Set for 25455 25465 25480 25490
- Replaces Ball Joints on SPC Arms – 25455, 25465, 25480, 25490
- Will not work on OEM or any other brand aftermarket upper control arms (UCA’s)
- Suits 2008-22 Toyota Sequoia & 2007-21 Toyota Tundra
- Suits 2003-2024 Toyota 4Runner, 2006-2017 Toyota FJ Cruiser, 2003-2009 Lexus GX470, 2010-2023 Lexus GX460
- Suits all Toyota Land Cruiser 200 Series and Lexus LX570 models – 2008-2021
- Suits 1998-2007 Toyota Landcruiser 100 Series and 1998-2007 Lexus LX470
- Sold in Pairs
- Fully seated boot to keep grease in and contaminants out for a maintenance-free joint
- High strength steel forging with offsets provides camber & caster adjustability
- One piece polymer race tests like OE and provides low & smooth turning torque
- Oversized ball generates 80˚ of articulation with a 25% increase in neck cross section vs. OE for added strength
- Modern grease formula ensures quiet and smooth operation with reduced wear for extended life
- Extended threads on ball stud will work with most popular spindle gusset kits
- These ball joints are reverse compatible and a direct replacement for the SPC upper control arm sets
- Installation Instructions
(9 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesFront +2″ 4Runner Long Travel Kit | Toyota 4Runner 2003-2024
- Suits Toyota 4Runner 2003-2024 2WD and 4WD
- Adds 2.0″ of width to either side for a total of 4″ total track width added!!!
- 4WD requires long travel axle shafts or full axle assemblies
- 2” Wider Per Side: Adds 2” of width per side, boosting suspension travel by 25%.
- Stock Fender Compatibility: Works with stock fenders when using positive offset wheels.
- Aggressive Look Option: Supports zero or negative offset wheels with flared fenders.
- Extended Wheelbase: Allows proper fitment of 35” tires.
- SilentSpin Bushings: Greaseless bushings in upper control arms for low maintenance.
- Delrin Bushings with PTFE: Smooth operation in lower control arms with PTFE-infused Delrin.
- Heavy-Duty Moog Ball Joints: Reliable outer pivots with heavy-duty Moog ball joints.
- Aluminum Skid Plates: Replaceable skid plates protect lower arms on rough trails.
- Flexible Installation: Compatible with coilovers, coilovers with bypasses, or coilovers with bump stops.
- Aluminum Strike Pads: Designed for optimal bump stop engagement.
- Complete Hardware Included: Comes with all necessary mounting hardware.
- Made in the USA: Proudly designed and manufactured in the United States.
- What’s Included:
- Boxed plate upper control arms
- Boxed plate lower control arms
- 8″ quad wrapped limit straps
- Weld on adjustable limit strap mounts
- 17-4 stainless steel tie rod extensions
- DOT approved extended brake lines
- Grade 8 mounting hardware
- Billet aluminum bump stop strike pad
- Zinc plated bushing washers
- No coilovers or bump stops are included!!
- Installation instructions 2009 and Older and 2010+
(0 reviews) -
Bilstein
Bilstein 25-325096 – 5160 Series Rear Right Shock
- Suits 2003-2024 Toyota 4Runner, 2003-2009 Lexus GX470, 2010-2023 Lexus GX460, 2006-2017 FJ Cruiser
- Suits 0-2″ of lift
- Type: Nitrogen Gas Charged
- With Coil Spring: No
- Internal Design: Monotube
- Adjustable Valving: No
- Extended Length (IN): 23.5 Inch
- Compressed Length (IN): 14.25 Inch
- Upper Mounting Style: Stud
- Lower Mounting Style: Eyelet
- Body Color: Silver
- Quantity: Single
- With Reservoir: Yes
- Includes Dust Shield: Yes
- Includes Hardware: Yes
- Includes Boot: Yes
- Estimated Install Time (Hours): 1
- Sold individually – This is the Right (passenger) side rear shock
- Link to matching left side shock
(7 reviews) -
Bilstein
Bilstein 25-311211 – 5160 Series Rear Left Shock
- Suits 2003-2024 Toyota 4Runner, 2003-2009 Lexus GX470, 2010-2023 Lexus GX460, 2006-2017 FJ Cruiser
- Suits 0-2″ of lift
- Type: Nitrogen Gas Charged
- With Coil Spring: No
- Internal Design: Monotube
- Adjustable Valving: No
- Extended Length (IN): 23.5 Inch
- Compressed Length (IN): 14.25 Inch
- Upper Mounting Style: Stud
- Lower Mounting Style: Eyelet
- Body Color: Silver
- Quantity: Single
- With Reservoir: Yes
- Includes Dust Shield: Yes
- Includes Hardware: Yes
- Includes Boot: Yes
- Estimated Install Time (Hours): 1
- Sold individually – This is the Left (driver’s) side rear shock
- Link to matching right side shock
(7 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.5 4Runner DCA Remote Resi Coilovers | 2003-2024
- Suits Toyota 4Runner 4th Gen and 5th Gen 2003-2024
- Not suitable for KDSS vehicle due to reservoir mounting position
- Comes preset to 2.0″ of lift
- Dual Compression Adjuster (DCA) is on the resi to fine tune the ride quality
- Dual Compression Adjusters with 10 adjustments for each knob
- Increased suspension travel
- Specific valving for each vehicle providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Remote reservoir equipped with dual compression adjusters allowing for high-speed and low-speed compression adjustments
- Less seal drag with the 3/4″ shafts compared to traditional 7/8″ shafts resulting in smoother operation
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Cold wound, high-tensile alloy steel coil springs that retain consistent rate and ride height
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2.5″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 3/4″ shafts
- Provides up to 3” of lift | Must be paired with aftermarket UCA
- Note: We do not recommend lifting the vehicle more than 3″. Excessive preload will reduce the ride quality
- What’s Included:
- 2.5 DCA coilover shocks with remote reservoirs Pair
- Coils installed are 13” long, 700 LBF/in Spring Rate
- Sway bar relocation mounts with reservoir brackets
- Spanner wrench
- All necessary mounting hardware
- Installation instructions
- Installation video is down below
- Matching Rear Shocks
(4 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.0 IFP Mid Travel Package | 4Runner FJ Cruiser GX470 GX460
- Suits 4th and 5th Gen Toyota 4Runner 2003-2024, Lexus GX470 2003-2009 and Lexus GX460 2010-2023
- Includes preassembled front Coilovers, Rear Shocks, and preassembled UCA’s
- Front comes preset to 2.0″ of lift with stock weight
- Increased suspension travel
- Vehicle specific valving providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Cold wound, high-tensile alloy steel coil springs that retain consistent rate and ride height
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 5/8″ shafts
- Provides up to 3” of front lift, rear shocks suit 1.5″ of lift
- Note: We do not recommend lifting the vehicle more than 3″. Excessive preload will reduce the ride quality
- What’s Included:
- 2.0 Dirt King IFP Series coilovers Pair
- Coils installed are 13” long, 700 LBF/in Spring Rate
- 2.0 Dirt King IPF Smooth Body Rear Shocks Pair
- Dirt King Tubular Ball Joint UCA’s
- Sway bar relocation mounts
- Spanner wrench to adjust height/preload
- All necessary mounting hardware
- Installation instructions
(7 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.0 IFP Smooth Body Shocks Pair | 4Runner FJ Cruiser GX470 GX460
- Suits Toyota 4Runner 4th and 5th Gen 2003-2024, FJ Cruiser all years, Lexus GX470 and GX460
- Suits up to 1.5″ of lift
- Increased suspension travel
- Vehicle specific valving providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 5/8″ shafts
- What’s Included:
- 2.0” IFP smooth body shocks Pair
- Shock shaft boots
- All necessary mounting hardware
- Installation instructions
(4 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.0 IFP 4Runner Coilovers Pair | 4Runner 2003-2024
- Suits Toyota 4Runner 4th Gen and 5th Gen 2003-2024
- Increased suspension travel
- Vehicle specific valving providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Cold wound, high-tensile alloy steel coil springs that retain consistent rate and ride height
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 5/8″ shafts
- Provides up to 3” of lift | Must be paired with aftermarket UCA
- Note: We do not recommend lifting the vehicle more than 3″. Excessive preload will reduce the ride quality
- What’s Included:
- 2.0 Dirt King IFP Series coilovers Pair
- Coils installed are 13” long, 700 LBF/in Spring Rate
- Sway bar relocation mounts
- Spanner wrench to adjust height/preload
- All necessary mounting hardware
- Installation instructions
- Matching Rear Shocks
(4 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesFront 4Runner Long Travel Kit | 4Runner FJ GX460 2010-2024
- Suits Toyota 4Runner 5th Gen and Lexus GX460 2010-2024, and FJ Cruiser 2010-2016
- 4WD requires long travel axle shafts or full axle assemblies
- Wheel Travel Specs, Tire Size and Shock recommendations are down below
- Bolt on application, minimal modifications required
- Utilizes American made FK bearings
- 4130 chromoly uniball cups
- Choice of ¾” heims or poly bushings for the UCA’s
- Delrin bushings for the LCA’s
- Zinc plated inner bushing sleeves
- Grease fittings for easy servicing
- 3/16″ and 1/8” boxed plate construction
- Internally ribbed with extrusions for weight reduction
- Bump stop plating
- Limit strap tabbing
- Bypass Tabbing
- To achieve the full amount of travel on 4WD models you must install a 1” diff drop kit and machine the inner CV’s for more articulation
- MADE IN THE USA
(7 reviews) -
RCV AxlesFREE SHIPPING
within 48 US StatesRCV Ultimate IFS CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- Standard length for use on lifted and non-lifted applications
- RCV Ultimate IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- Ultimate IFS CV Axles provide increased strength that original equipment axle shafts just can’t match
- Even if you have big tires and big power there are no worries
- Ultimate IFS CV Axles are low maintenance, and are backed with a “No Questions Asked” limited lifetime warranty against breakage
- Warranty Form
- Our IFS CV axles meet and exceed the strength of a straight axle swap, while allowing you to maintain the traction, smoothness and control of your IFS
- The axles feature a double-offset inboard CV joint that is comprised by 1-inch balls and 300M internal components
- The outboard CVs utilize our Dana 60 architecture with combination of 4340 & 300M components optimized for maximum strength
- The center bar is 35 spline 300M, the strongest in the industry
- The RCV developed moly SPEC grease is used in the CVs to control heat build-up in even the most extreme use environments
- Black oxide coating is standard
- Sold as a pair
- Made in the USA
(9 reviews) -
MRA Remote Resi 3-Way Adjustable MonotubeFREE SHIPPING
within 48 US StatesDobinsons 2.6″ 3-Way Adjustable Front Long Travel Coilovers Pair | Toyota & Lexus
- Dobinsons Long Travel Coilovers for the front of Toyota and Lexus Trucks and SUV’s
- Intended to be used on 4th and 5th Gen 4Runners, Lexus GX470 and GX460, FJ Cruisers, and Toyota Tacoma 2nd and 3rd Gens – with all Long Travel Parts Installed (upper and lower arms, axles, custom bump stops, limit straps, etc)
- Includes Different bolt pattern adapters for Top mount plate
- Specifications: 602mm (23.7″) extended, 399 mm (15.7″) compressed, uses 1.5″ long x 1/2″ Bolt for lower mounting
- Pair of Coilover Struts only, no coils included
- Height adjustable with a fully threaded body
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Does not include coil springs – sold separately
- These can only be run with aftermarket UCA’s for coilover clearance and full long travel lower arms – they will not work with OEM sized upper or lower arms
- Recommended Coils to run with these:
- C92-3016550 | Inner Diameter – 3.0″ | Length – 16″ | Spring Rate – 550lb/in
- C92-3016600 | Inner Diameter – 3.0″ | Length – 16″ | Spring Rate – 600lb/in
- C92-3016650 | Inner Diameter – 3.0″ | Length – 16″ | Spring Rate – 650lb/in
(9 reviews) -
4Runner 5th Gen (2010-2024)FREE SHIPPING
within 48 US StatesDobinsons 3″ Long Travel 4Runner IMS Suspension Kit for 2010-24
- Suits Toyota 4Runner 5th Gen 4×4 from 2010 to 2024, without KDSS only
- Extended Travel front struts and Long Travel Rear shocks along with all related components are listed on this page
- Maximize the suspension travel of your Toyota 4Runner for the most flex and travel you can get from bolt-on parts
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Lifting 3″ front and rear maintains factory rake
- Dobinsons have the largest selection of front and rear coils for 4Runners and in multiple colors
- Add up how much accessory weight you have on the front and then the rear, that’s your constant load
- Then choose the lift height from the coils that most closely matches the added weight
- Fully rebuildable and re-valvable shocks and struts
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Option to have the front struts preassembled prior to shipping to make installation easier at home
- You choose what options you want, nothing is provided if it is not listed once you have selected it
- Suspension Installation Video
- Lift heights are based on the standard 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. Many vehicles come in at different heights from the factory based on trim levels and options
(5 reviews) -
4Runner 4th Gen (2003-2009)FREE SHIPPING
within 48 US StatesIcon Tubular Upper Trailing Arms Pair | 4Runner FJ Cruiser GX470 GX460
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460
- CNC machined & notched 1026 DOM steel construction
- Multi durometer bushing for noise free operation and maximum angularity
- No grease required for life of bushings
- Quality JM12T PTFE-lined FK Rod Ends
- Adjustable for various lift heights & driveline angles
- ICON1K tested in extreme off-road conditions
- Fabricated components covered under ICON’s lifetime warranty
- Sold as a Pair
- Installation Guide
- Warranty Info
(8 reviews) -
4Runner 4th Gen (2003-2009)FREE SHIPPING
within 48 US StatesIcon Billet Upper Trailing Arm Pair | 4Runner FJ Cruiser GX470 GX460
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460
- CNC machined, billet aluminum construction
- Chemical etched, clear anodized finish for corrosion resistance
- On-vehicle adjustability using ICON’s pinch housing and double adjuster
- 3/4″ Rod End and Polyurethane Pivots, for excellent strength and longevity
- High Misalignment Spacers for Excellent Articulation
- Sold as a Pair
- Installation Guide
- Warranty Info
(7 reviews) -
200 Series Land Cruiser (2008-2021)FREE SHIPPING
within 48 US StatesIcon Billet Lower Trailing Arm Pair | 4Runner FJ Cruiser GX470 GX460 LC200
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460, Lexus LX570 and 200 Series 2008-2021
- On vehicle length adjustment for different ride heights and pinion angles using ICON’s Double Adjuster System
- Vehicle specific, high clearance design for reduced link contact with obstacles
- Replaceable Nylon ROCK Slider to protect the link from damage
- CNC machined 6061 aluminum construction
- Large FK Bearing JMX16T PTFE-lined rod ends
- Greaseable, multi-piece polyurethane bushings for maximum angularity and noise isolation
- Covered by ICON’s Limited Lifetime Warranty
- Sold as a Pair
- Installation Guide
- Warranty Info
(7 reviews) -
200 Series Land Cruiser (2008-2021)FREE SHIPPING
within 48 US StatesIcon Tubular Lower Trailing Arm Pair | 4Runner FJ Cruiser GX470 GX460 LC200
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460, Lexus LX570 and 200 Series 2008-2021
- CNC machined & notched 1026 DOM steel construction
- Multi durometer bushing for noise free operation and maximum angularity
- No grease required for life of bushings
- Quality JM16T PTFE-lined FK Rod Ends
- Adjustable for various lift heights & driveline angles
- Offset lower link front pivots improve roll steer
- Tangent lower link barrel design reduces risk of off-road hangups
- Integrated OEM emergency brake bracket mount
- ICON1K tested in extreme off-road conditions
- Fabricated components covered under ICON’s lifetime warranty
- Sold as a Pair
- Installation Guide
- Warranty Info
(7 reviews) -
Bump Stops & SpacersFREE SHIPPING
within 48 US StatesDobinsons 2.2″ Hydraulic Bump Stop IFS Weld on Mount Kit
- Kit includes front Weld on Mounts (Pair) and Dobinsons HBS56-009 Pair of Hydro Bump Stops
- Made for IFS (independent front suspension) vehicles to replace the OEM rubber bump stop
- HBS56-009 – 56mm (2.2″) body | 46mm (1.8″) stroke | 188mm (7.4″) extended | 142mm (5.6″) compressed | 105mm (4.0″) thread length
- CNC Machined 50mm Billet Aluminum Piston
- EDP Coated 3mm Thick 56mm Steel Body
- Threaded Body For Height Adjustment
- Supplied with both Interchangeable Super Quiet Rubber Rod End & Hard Nylon
- 30mm Micro Polished Hard Chrome Shaft
- Slow Rebound Valving To Prevent Bucking
- Removable Dust Cover Boot For Stealth Appearance
- Fully Rebuildable & Tunable
- O-Ring Travel Indicator
- Heavy Duty Extreme-Race style Triple Seal Design
- Nitrogen Gas Charged & Tunable (100 to 300 PSI)
- Pre-charged to 150 PSI
- Extra Short Dead Lengths For Compact Fitment
- Universal design threaded weld on bump stop can to hold the 2.2″ body bump stop
- Cans have 3mm walls for increased strength
- Kit is ideal for those who bottom out often in their offroad driving or go really hard at high speeds
- Could suit a wide range of vehicles as listed below, but remember they are universal and will require adaptation to your vehicle and welding
- Custom fitting and welding is required
- Photo attached shows these bump stops installed with the weld-on mounts on a 3rd Gen Tacoma
(0 reviews)
