Full Suspension Kits - Sequoia 3rd Gen

Showing all 5 resultsSorted by popularity

Sequoia 3rd Gen (2023-2024+)
FREE SHIPPING
within 48 US States
Dobinsons 3-4″ IMS Sequoia Lift Kit for 2023-2024+
- Suits 2023-2024+ Toyota Sequoia 4×4 Models
- A 2023+ Sequoia came with a front ride height 1″ lower than a 2022+ Tundra, so we’re able to offer a 4″ lift on these, which is a 3″ on a Tundra, and still within the limits of the IFS
- Fully rebuildable and re-valvable monotube shocks
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment
- Front IMS struts for this application have multiple clip heights to adjust ride height if needed
- Full 2 year limited warranty, no set rebuild time period
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Does not suit air suspension equipped models
- Coil seat for IMS59-60446 should be set at 175mm (6.87″) from the strut bushing eye
- 3″+ of front lift requires new aftermarket UCA’s for proper alignment and clearance
- If doing a 4″ lift in the front, a diff-drop kit or longer TRD CV-axles are REQUIRED, failure to complete these requirements could cause OE CV-axle failure
- TRD axle shafts: PT362-3432B and PT362-3431B
- Front IMS struts assembly instructions
Rated 5.00 out of 5
(6 reviews)
From $1,945.00 Select options
Sequoia 3rd Gen (2023-2024+)
FREE SHIPPING
within 48 US States
Dobinsons 3-Way Adjustable MRR Sequoia Lift Kit | 2023-2024+ (3-4″)
- Suits 2023-2024+ Toyota Sequoia 4×4 Models
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- A 2023+ Sequoia came with a front ride height 1″ lower than a 2022+ Tundra, so we’re able to offer a 4″ lift on these, which is a 3″ on a Tundra, and still within the limits of the IFS
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Remote Reservoir 3-way adjustable Shocks, Superior Design, thicker walls, longer travel
- Adjust high and low speed compression (HSC and LSC) and rebound adjustment front and rear
- Massive 66mm (2.6″) body size with 60mm pistons front and rear
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen in the external reservoir
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- Does not suit air suspension equipped models
- Coil seat for MRA59-A446 should be set at 175mm (6.87″) from the strut bushing eye
- 3″+ of front lift requires new aftermarket UCA’s for proper alignment and clearance
- If doing a 4″ lift or higher in the front, a diff-drop kit or longer TRD CV-axles are REQUIRED, failure to complete these requirements could cause OE CV-axle failure
- TRD axle shafts: PT362-3432B and PT362-3431B
- Front Installation Instructions
Rated 5.00 out of 5
(9 reviews)
From $3,335.00 Select options
Shocks + Struts - Sequoia 3rd Gen
FREE SHIPPING
within 48 US States
Dobinsons 3.0-4.0″ 3-Way Adjustable MRA Coilovers for Toyota Sequoia 2023+
- Suits Toyota Sequoia 2023-2024+ Models
- TRD Pro Models yield 1″ less lift than listed here, as they are already lifted taller than base models
- Sold as a Pair, ready to bolt in
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment
- Looking for a quick and easy way to lift your Sequoia? This is your answer
- Select your desired lift height and tell us your weight – we’ll take care of the rest!!
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- SOLD IN PAIRS
- Full 2 year limited warranty, no set rebuild time period
- Must mount the banjo fitting and hose inwards on MRA struts
- Coil seat for MRA59-A446 will be set at 175mm (6.87″) from the strut bushing eye
- Photos for illustration purposes
- Instructions for setting and adjusting coil seat height
- Note about lift heights – all vehicles can have some variance and desired lift height may need to be adjusted to suit your specific vehicle. Adding 2.5″ or more lift, new UCA’s should be added for proper articulation and correct wheel alignment
- If doing a 4″ lift in the front, a diff-drop kit or longer TRD CV-axles are REQUIRED, failure to complete these requirements could cause OE CV-axle failure
- TRD axle shafts: PT362-3432B and PT362-3431B
- Front Installation Instructions
- Link to Matching rear shocks
- A Diff Drop Kit should be run with 4″ of lift
- Please NOTE: Assembled coilovers cannot be returned, as they are made to order
Rated 5.00 out of 5
(7 reviews)
$1,960.00 Select options
Shocks + Struts - Sequoia 3rd Gen
FREE SHIPPING
within 48 US States
Dobinsons 3.0-4.0″ Assembled IMS Coilovers for Toyota Sequoia 2023+
- Suits Toyota Sequoia 2023-2024+ Models
- TRD Pro Models yield 1″ less lift than listed here, as they are already lifted taller than base models
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment
- Looking for a quick and easy way to lift your Sequoia? This is your answer
- Select your desired lift height and tell us your weight – we’ll take care of the rest!!
- Dobinsons IMS are height adjustable by a threaded body with adjustable collar
- The Dobinsons IMS Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes – Sequoia IMS coilovers use a slightly different top mount
- Instructions for setting and adjusting coil seat height
- Note about lift heights – all vehicles can have some variance and desired lift height may need to be adjusted to suit your specific vehicle. Adding 2.5″ or more lift, new UCA’s should be added for proper articulation and correct wheel alignment
- If doing a 4″ lift in the front, a diff-drop kit or longer TRD CV-axles are REQUIRED, failure to complete these requirements could cause OE CV-axle failure
- TRD axle shafts: PT362-3432B and PT362-3431B
- Link to Matching rear shocks
- A Diff Drop Kit should be run with 4″ of lift
- Please NOTE: Assembled coilovers cannot be returned, as they are made to order
- Note: If you’re looking for less lift height, you can buy these IMS Struts only and use them with your OEM coils and add preload to add lift height
Rated 5.00 out of 5
(3 reviews)
$1,270.00 Select options
Tundra 3rd Gen (2022-2024)
2″ Front Strut Spacer Kit for Tundra 2022+ & Sequoia 2023+
Suits 2022+ Toyota Tundra and 2023+ Toyota Sequoia

Note: Not for use on Tundra or Sequoia equipped factory rear air, TRD PRO, or TRD Off-Road.

ReadyLIFT leveling kits are the fastest, safest, most cost-effective way to bring the front of your vehicle level with the rear for that ideal lifted neutral stance.

Our front strut assembly eliminates the hassle, time, and concern of compressing springs.

A ReadyLIFT leveling kit will maintain a smooth OEM ride without adding stress to stock suspension components!

The all-new part number 66-52200 2022-UP Toyota Tundra Leveling Kit is an excellent choice for those who want a level stance while running larger tires up to 34 inches.

The no-trim maximum tire size for this kit is a 295-60R20 with a 20” X 9” wheel and +18 offset.

Fabricated Steel Front Strut Spacers With Durable Black Powder Coat Finish

Product Will Retain Ride Or Handling Quality

Engineered And Built To Provide Years Of Trouble Free Service

Made In USA

Limited 1 Year Warranty

Download Pdf Instructions
Rated 5.00 out of 5
(9 reviews)
$229.95 Add to cart