You may be interested in…

• 

  • 
  • 
  • 

  GX460 (2010-2023)

  Dobinsons 1.5-3.5″ Lift Kit for Lexus GX460 2010 to 2023 (all options)

  • Every suspension option from Dobinsons to lift your Lexus GX460 all on one page
  • Here you can lift from a low height up to the maximum bolt-on lift height by making your selections below
  • Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
  • Coils are specifically suited to the additional accessory load (weight) on the vehicle
  • Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
  • High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
  • Base Kit Includes 2 Front Twin Tube Struts, 2 Rear Twin Tube Shocks, and 4 Coil Springs
  • You can choose to upgrade to the higher end IMS or MRA struts and shocks on this page in the drop down menus

  From $1,200.00 Select options
• 

  • 
  • 

  Timbren

  Ships FREE !!
  within 48 US States

  Timbren ABSTOF Active Off Road Front Bump Stops | Toyota and Lexus

  • Suits 2000-2024 Tundra,  2001-2024 Sequoia, 2005-2023 Tacoma, 1990-2024 4Runner, FJ Cruiser, Lexus GX470 and GX460, Landcruiser 100 and 200 Series
  • Note: Some 2nd Gen Toyota Sequoia models have 2 sets of front bump stops, so ordering 2 of these kits will be necessary to replace them all.  Inspect your vehicle before ordering
  • Maintain Full Axle Travel
  • Smooth Axle Engagement and Disengagement
  • Enhance Suspension Performance
  • Progressive Spring Rate
  • Absorbs Energy and Cushions Road Shocks
  • Stronger Than OEM Bumpstops
  • Easy Installation – Installation Video
  • Satisfaction Guarantee
  • Lifetime Warranty
  • Click here for instructions

  $269.36 Add to cart
• 

  Dobinsons

  Dobinsons Big Bore Steering Damper for Jeep Cherokee Wrangler Grand Cherokee, models XJ YJ TJ ZJ WJ JK

  • Induction Hardened Rods for strength, no Viscosity Drop due to High Shear Stability
  • Cellular Foam Cell Insert, Teflon Piston Rings
  • Excellent Viscosity Temperature Performance
  • NOK Triple Lip Oil Seals, High Quality Fuchs German Oil
  • Replaces OE steering damper, bolts into place. Can be used with or without a lift.

  $135.00 Add to cart
• 

  • 
  • 
  • 

  ARB

  ARB510 ARB Air Systems E-Z Tire Deflator with Digital Gauge and Pouch

  • Easily lower your tire pressure with a clear digital readout, while you prep your vehicle to hit the trails
  • Lowering your tire pressure is a MUST when going offroad for increase comfort, better traction, better tire pattern, and higher performance from your vehicle
  • Easy-to-read blue backlit display screen, Large LCD digital readout
  • Multiple measurements available: 0-14 bar, 0-200 psi, 0-1400 kpa, 0-14 KgF
  • Auto switch off, Auto switch on
  • 250mm braided line
  • High-quality brass components and crimps
  • Rubber bump guard to protect against drops
  • Screw-on chuck suits all Schrader valves
  • Accuracy to +/- 1psi at 15-75psi
  • Includes updated larger canvas pouch for storage

  $83.00 Add to cart
• 

  • 
  • 
  • 

  All Pro Offroad

  Ships FREE !!
  within 48 US States

  All Pro Tacoma IFS Skid Plate – Aluminum Black

  • Suits 2005-2023 Toyota Tacoma 4×4 Models
  • Covers from the front bumper down to the first cross member
  • 1/4-inch aluminum construction – Black Powder Coated Steel
  • Optimal balance between strength and weight
  • Save yourself from costly underbody repairs with this easy to install Tacoma skid plate
  • Easy, bolt-on installation using all factory hardware
  • Compatible with stock bumpers
  • Available in 4 variants – Steel or Aluminum, Bare or Powder Coated
  • Installation Instructions

  $440.00 Add to cart
• 

  • 
  • 
  • 

  Air Compressors

  ARB CKMTA12 12V High Performance Twin Air Compressor

  • Motors are water sealed, 100% ball bearing equipped (i.e. no bushings), and feature a unique linear brush pre-load system for extra long life, low heat and quiet operation throughout the life of the unit.
  • Compact twin motor, dual cylinder design makes it the highest flowing compressor in its class (voltage vs. size). Highest air flow rate of any 12V compressor of its size on the market at 174LPM [6.16CFM].
  • Full wiring loom included for simplified installation and easy plug-in connectivity to Air Locker control solenoids. (Note: Air Locker Manifold Kit #171503 required to mount solenoids).
  • Motors are internally thermal protected against extreme temperature damage. Over-pressure safety valve equipped. Equipped with dual heavy duty Maxi-Fuses for professional in-line circuit protection and true circuit redundancy in case of a fault.
  • Compressor pistons are equipped with a heavy duty European made cylindrical roller bearing. Hard-anodized cylinder bores and PTFE (Teflon) impregnated carbon fibre piston seals for reduced friction and maximum trouble free life.
  • 12V, Draws 50 Amps max, 6.16 CFM, 150 PSI max, 100% Duty Cycle
  • 10.9 x 7.5 x 4.1 inches actual dimensions, 19.4 LBS with all items included

  $616.00 Add to cart
• 

  Dobinsons

  Dobinsons Add-A-Leaf Center Bolt Pin (Single) (10-75)

  • Used in place of original leaf bolt when adding a leaf
  • Fits L59-111-R-R3 &  L59-112-R-R5 ONLY
  • Sold individually

  • Made from the highest quality raw materials to give years of life under the harshest conditions
  • Over 60 years of leaf spring design and manufacturing
  • Requires lifted leaf springs to ensure proper fitment

  $5.00 Add to cart
• 

  • 
  • 
  • 

  Exceptions

  Ships FREE !!
  within 48 US States

  Dobinsons MRA59-A575 3-Way Adjustable MRA Long Travel Rear Shocks

  • Suits 2003-2024 4Runner (4th and 5th Gen), All FJ Cruisers, Lexus GX470 & GX460 without KDSS, Toyota Prado 120 & 150, suitable for 2 – 3.5″ of lift
  • CANNOT BE USED WITH KDSS
  • 3-way adjustable valving – adjust high and low speed compression and rebound
  • MRA59-A575 – Specifications.  730mm extended, 443mm compressed
  • Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
  • 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
  • 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
  • 20 Stage Low Speed Compression – For creepy crawling and cornering
  • 15 Stage Rebound – Control your coils, prevent bucking
  • 50mm CNC Machined High Flow Billet Aluminum Race Piston
  • 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
  • Upgraded 3 Stage FKM‐HNBR Sealing System
  • TSUGAMI™ CNC machined components for precise tolerances
  • Parker™ Braided High Pressure Hoses
  • 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
  • T6 6061 Height Adjustable Spring Seat
  • Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
  • 60mm Full 6063 aluminum remote reservoir
  • Lightweight CNC Machined Low Friction floating piston
  • High Quality O.E.M. Grade Natural Rubber Bushings
  • Single Piece Lower Leg
  • EDP Surface Protection
  • Direct Bolt-On Shock Design
  • CNC TIG Precision Welded Body End Mounts
  • Fully Rebuildable Design
  • SOLD IN PAIRS
  • Includes Universal Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
  • Can Use with Timbren Rear Bump Stop Kit
  • Replacement Brake Lines are required: Extended Brake Lines
  • Bump stops extensions or longer bump stops are required!!
  • Full 2 year limited warranty, no set rebuild time period
  • Now comes with a longer hose and different mounting instructions

  $1,280.00 Add to cart
• 

  • 
  • 
  • 

  GX470 (2002-2009)

  Dobinsons 1″ to 3.5″ Lift Kit for Lexus GX470 (All Options)

  • Full Dobinsons Complete Suspension kit for Lexus GX470 from 2003 to 2009, with every possible option listed on one page
  • Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
  • Coils are specifically suited to the additional accessory load (weight) on the vehicle
  • Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
  • High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
  • Base Kit Includes 2 Front Twin Tube Struts, 2 Rear Twin Tube Shocks, and 4 Standard Coil Springs
  • Select the type of struts and shocks you want as well as all possible add-ons down below
  • Choose from Dobinsons Classic Twin Tube shocks, IMS Monotube, or MRA 3-way adjustable remote resi shocks
  • See note below in description about KDSS models

  From $1,200.00 Select options
• 

  • 
  • 
  • 

  Dobinsons

  Ships FREE !!
  within 48 US States

  Dobinsons 12V Zenith 6.0 CFM Air Compressor Kit High Output

  • 170L/ minute Air Flow
  • Integrated Air Tank
  • 2 x 1/8” NPT Auxiliary fittings
  • Carry Bag
  • 6.5 m Rubber Hose
  • Pressure Cut Off Switch
  • Safety Release Valve
  • Removable Base for Permanent Mounting
  • Quick Release Tyre Chuck

  $420.00 Add to cart
• 

  SPC

  SPC 87520 – Nissan Frontier Xterra Alignment Cam Kit (2 Pairs)

  • Suits 2005+ and 2022+ Nissan Frontier and Nissan Xterra (2005-2015)
  • These cams are designed to install in the lower control arms for camber and caster adjustment
  • They replace the original non-adjustable lower control arm bolts
  • Front Adjustment range: Camber/Caster ±2.00°
  • Installation time: .3 hr/side
  • The purchase includes 2 pairs, enough for 1 vehicle
  • Installation Guide

  $90.00 Add to cart
• 

  • 
  • 
  • 

  All Pro Offroad

  Ships FREE !!
  within 48 US States

  All Pro Tacoma IFS Skid Plate – Steel Black Coated

  • Suits 2005-2023 Toyota Tacoma 4×4 Models
  • Covers from the front bumper down to the first cross member
  • 3/16-inch steel – Black Powder Coated Steel
  • Optimal balance between strength and weight
  • Save yourself from costly underbody repairs with this easy to install Tacoma skid plate
  • Easy, bolt-on installation using all factory hardware
  • Compatible with stock bumpers
  • Available in 4 variants – Steel or Aluminum, Bare or Powder Coated
  • Installation Instructions

  $440.00 Add to cart
• 

  • 
  • 
  • 

  Dobinsons

  Dobinsons Adjustable Rear Sway Bar End Link Kit | 4Runner FJ Cruiser GX470 GX460

  • Suits 4th and 5th Gen 4Runner 2003-2024, FJ Cruiser (all years), GX470, GX460 (without KDSS)
  • Order 1 for 1 vehicle
  • Heavy Duty, zinc plated, with high quality ball joint ends for long life
  • Kit includes 2 sway bar links, everything as shown in the photo, enough for 1 vehicle
  • Will also suit stock non-lifted vehicles simply looking to replace their worn out rear links
  • Adjustable to suit lift heights of 2″ to 4″
  • Watch a video here to see more about these: https://youtu.be/lZACSaE2PHI
  • Note: Product was updated to bigger/thicker stud of the ball joint in 2020, no longer needing the small sleeve shown in the product video.  Some vehicles’ sway bar is too thick to use the thick supplied washer, so reuse the stock washer if necessary

  $200.00 Add to cart
• 

  • 
  • 
  • 

  Air Compressors

  ARB CKMA12 High Performance Medium 12V Air Compressor

  • Designed specifically to run one or two Air Lockers and to air up tires (requires kit)
  • Constructed of lightweight, high-strength, engineering-grade materials, including military and aerospace-grade components
  • Relocatable, splash-resistant air filter with washable high-flow sintered bronze filter cartridge for cleaner, cooler air supply
  • Fully sealed components for moisture and dust protection
  • Over-pressure safety valve-equipped
  • Pressure switch-controlled air manifold system specially designed for ARB Air Lockers
  • Hard-anodized cylinder bore and PTFE-impregnated carbon fiber piston seal for reduced friction and maximum life
  • Anti-vibration, sound-deadening, anodized mount dissipates motor heat and allows compressor to be repositioned 180 degrees
  • Ball bearing-equipped motor (no bushings) with unique, linear brush, pre-load system for long life, low heat, and quiet operation
  • Compressor piston equipped with a German-made, high shock-rated, cylindrical roller bearing
  • Motor is internally thermal-protected against extreme temperature damage
  • Comprehensive-photo illustrated installation guide
  • 12V DC, Draws 14.2 Amps, 2.34 CFM, 100 PSI max

  $338.00 Add to cart
• 

  Tacoma 3rd Gen (2016-2023)

  Dobinsons Tacoma L59-112-R Heavy Duty Leaf Springs Pair for 2005-2023 (800-1200LBS)

  • Suits Toyota Tacoma 2005-2023, lifts 2-2.25″ with at least 800LBS of constant load on the rear end
  • Sold in pairs
  • Each pack has 7 leaves
  • Made from the highest quality raw materials to give years of life under the harshest conditions
  • Over 60 years of leaf spring design and manufacturing
  • Design features include Drawn, tapered and thinned leaf ends
  • Manufactured to international quality standards ISO9001:2008 using premium grade Sup 9 silicon manganese spring steel,
  • Anti-Friction inter leaf liners are use to reduce the friction at each leaf end where the load is creates and provides a smoother, quieter ride.
  • Click here for Extra Leaf Kit for additional load support
  • These are leaf springs ONLY and don’t come with bushings or any other parts.  Scroll down for add-ons that go with these springs

  $870.00 Add to cart
• 

  • 
  • 
  • 

  All Pro Offroad

  Ships FREE !!
  within 48 US States

  All Pro Tacoma IFS Skid Plate – Raw Aluminum

  • Suits 2005-2023 Toyota Tacoma 4×4 Models
  • Covers from the front bumper down to the first cross member
  • 1/4-inch aluminum construction – Raw aluminum
  • Optimal balance between strength and weight
  • Save yourself from costly underbody repairs with this easy to install Tacoma skid plate
  • Easy, bolt-on installation using all factory hardware
  • Compatible with stock bumpers
  • Available in 4 variants – Steel or Aluminum, Bare or Powder Coated
  • Installation Instructions

  $380.00 Add to cart
• 

  • 
  • 
  • 

  ARB

  ARB505 E-Z Deflator Kit 10-60 PSI Rapid Air Down Offroad Kit

  • Corrosion resistant brass/stainless deflator tool
  • Fully geared, solid brass precision movement
  • Protective rubber gauge guard
  • Easy to read dial with one PSI increments
  • Includes updated canvas pouch for storage
  • Original analog design, newer digital version is now also offered

  $54.00 Add to cart
• 

  • 
  • 

  Timbren

  Ships FREE !!
  within 48 US States

  Timbren ABSTORSEQ Active Off Road Rear Bump Stops | Toyota and Lexus SUV’s

  • Maintain Full Axle Travel
  • Smooth Axle Engagement and Disengagement
  • Enhance Suspension Performance
  • Progressive Spring Rate
  • Absorbs Energy and Cushions Road Shocks
  • Stronger Than OEM Bumpstops
  • Easy Installation
  • Satisfaction Guarantee
  • Lifetime Warranty
  • Suits 4th and 5th Gen 4Runner (2003-2024), FJ Cruiser, Lexus GX470 and GX460, Landcruiser 100 Series

  • Specs:

    • 2,000 lb capacity
    • 4,800 lb bump load capacity
    • Overall kit height = 5”
    • Total deflected (compressed) height = 2.75”
    • Amount of deflection (compression) = 2.25”
  • Click here for instructions
  • Installation video from Exit Offroad
  • Depending on the overall travel of the suspension you’re running, bump stop extensions may be necessary to prevent shock bottom-outs.  Timbren make 2 options, they do not include any longer bolts which may be required
    • A25722-90F00 (1/2″ spacer)
    • A25723-90AD00 (1″ spacer)

  $269.36 Add to cart
• 

  Upper Control Arms

  Pair of UCA Pivot Bolts and Nuts | Toyota and Lexus

  • This is a pair of factory size upper control arm pivot bolts and nuts replacements to service two control arms
  • Commonly referred to “as the long UCA bolt”
  • Services both control arms at once
  • Does not come with any washers.  New aftermarket UCA’s usually come with the necessary washers
  • Vehicle Fitment
  • • 2003-2009 Toyota 4Runner
    • 2010-2024 Toyota 4Runner
    • 2005-2015 Toyota Tacoma
    • 2016-2023 Toyota Tacoma
    • 2006+ FJ Cruiser (all years)
    • 2003-2009 Lexus GX470
    • 2010-2023 Lexus GX460
    • Toyota Hilux Vigo
    • Toyota Hilux Revo
    • Toyota Fortuner
    • Toyota Prado 120
    • Toyota Prado 150
  • Bolt Grade: 10.9
  • Head Drive Type: Hex
  • Length: 351 mm
  • Material: Steel
  • SAE or Metric: Metric
  • Thread Diameter: 14 mm
  • Thread Length: 28.7 mm
  • Thread Size: 14 mm
  • Thread Type: Fine

  $69.00 Add to cart
• 

  • 
  • 
  • 

  Accessories

  Ships FREE !!
  within 48 US States

  Dobinsons 4Runner Snorkel Kit for 4Runner 5th Gen 2010-2024

  • Dobinsons 4Runner Snorkel kit for the 5th Gen models from 2010 to 2024
  • Rotationally molded using precision CNC shaped aluminum dies
  • Increases air intake height to allow safer water crossings and reduce dust intake
  • Increased air intake height rams cooler, cleaner air into the engine increasing engine performance
  • Manufactured from high quality UV resistant LLDPE
  • Snorkel Kits include template and all mounting hardware
  • Sure, you have to drill some holes, but installing front or rear bumpers also requires a lot of trimming, so why not add a snorkel!!

  $395.00 Add to cart
• 

  • 
  • 
  • 

  Dobinsons

  Ships FREE !!
  within 48 US States

  Dobinsons MRA45-A645 3-Way Adj Rear Shocks Xterra Frontier

  • Suits 2005-2015 Nissan Xterra, 2005-2021 Nissan D40 Frontier and Navara with up to 2.0″ of lift
  • 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
  • 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
  • 20 Stage Low Speed Compression – For creepy crawling and cornering
  • 15 Stage Rebound – Control your coils, prevent bucking
  • 50mm CNC Machined High Flow Billet Aluminum Race Piston
  • 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
  • Upgraded 3 Stage FKM‐HNBR Sealing System
  • TSUGAMI CNC machined components for precise tolerances
  • Parker Braided High Pressure Hoses
  • 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile
  • strength exceeding 700MPA
  • T6 6061 Height Adjustable Spring Seat
  • Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
  • 60mm Full 6063 aluminum remote reservoir
  • Lightweight CNC Machined Low Friction floating piston
  • High Quality O.E.M. Grade Natural Rubber Bushings
  • Single Piece Lower Leg
  • EDP Surface Protection
  • Direct Bolt-On Design
  • CNC TIG Precision Welded Body End Mounts
  • Fully Rebuildable Design
  • Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
  • Full 2 year limited warranty, no set rebuild time period
  • 565mm extended, 361mm compressed
  • Sold in Pairs

  $1,150.00 Add to cart
• 

  • 
  • 
  • 

  Recovery

  Ships FREE !!
  within 48 US States

  Overland Vehicle Systems Digital Tire Deflator with Valve Kit & Storage Bag

  • Oversized Digital Gauge
  • Heavy Duty Rubber Protective Cover
  • Illuminated Display
  • Anti Rust Brass and Stainless Steel Components
  • Reinforced Nylon Wrapped Air line
  • 3 Inch Circle Dial
  • 17 Inch Hose
  • Removes The Valve Core For Fastest Deflation
  • Instantly Read The PSI

  $34.99 Add to cart
• 

  • 
  • 
  • 

  Recovery

  Dobinsons 4×4 Off Road Rapid Tire Deflator with Gauge and Pouch

  • 0-60 PSI Gauge Included at 1PSI Increments, giving easy and accurate readings
  • Quick Release Coupling to Allow Pressure Checking at any time during Deflation
  • Corrosion Resistant Brass Fittings for Long Life
  • Includes Carry Case
  • Combine with Dobinsons Air Compressor and Deluxe Tire Repair Kit for a Complete Tire Maintenance Package

  $50.00 Add to cart
• 

  Airbag Kits

  Air Lift 60769 Air Spring Kit Rear Helper Airbags for 2-3″ of Lift

  • Suits all 3rd/4th/5th Gen 4Runners, FJ Cruiser, GX470, GX460 WITH 2-3″ of Lift
  • These are an alternate to Firestone 4108
  • Complete kit – 1 per vehicle
  • Inserts inside your rear coil springs to add additional load support
  • Manually inflate or deflate the air bags to add or remove support or height
  • Perfect for people who tow, or regularly load up fully and need additional height or support
  • Route the airlines to your rear bumper or a suitable place to easily add or remove air to the bags
  • Ships from multiple warehouses across the country for faster shipping times
  • Fitment Notes: NOTE: Custom modifications may be required for lifted applications to ensure air bags are properly supported. If using on a lifted application, do not follow bump stop/jounce cut instructions. You will need to determine where to cut based on your lift amount (not cutting off as much depending on lift height)
  • Installation Manual, Click Here

  $148.00 Add to cart