Your cart is currently empty!
Sway Bar Links + Brackets
Showing all 20 resultsSorted by popularity
-
4Runner 4th Gen (2003-2009)Dobinsons Adjustable Rear Sway Bar End Link Kit | 4Runner FJ Cruiser GX470 GX460
- Suits 4th and 5th Gen 4Runner 2003-2024, FJ Cruiser (all years), GX470, GX460 (without KDSS)
- Order 1 for 1 vehicle
- Heavy Duty, zinc plated, with high quality ball joint ends for long life
- Kit includes 2 sway bar links, everything as shown in the photo, enough for 1 vehicle
- Will also suit stock non-lifted vehicles simply looking to replace their worn out rear links
- Adjustable to suit lift heights of 2″ to 4″
- Length measured from the center of the lower ball joint to where the first washer sits – 125mm – 165mm (5.0″ – 6.5″)
- Watch a video here to see more about these:Â https://youtu.be/lZACSaE2PHI
- Note: Product was updated to bigger/thicker stud of the ball joint in 2020, no longer needing the small sleeve shown in the product video. Some vehicles’ sway bar is too thick to use the thick supplied washer, so reuse the stock washer if necessary
(15 reviews) -
SuspensionKDSS Spacer Kit – Lexus GX460 5th Gen 4Runner by Treaty Oak Offroad
- Suits 5th Gen Toyota 4Runner with KDSS (2010-2024) and Lexus GX460 (2010-2023)
- Made from 6061 aluminum, Type III hard coat anodized in black, and supplied with new hardware
- May require modification to your factory front skid plates due to additional down travel of the sway bar
- Helps correct incessant lean of a lifted vehicle with KDSS by adding a spacer to the fixed mount up front and to both mounts on the rear
- Bolt on installation – may require trimming of OE skid plate on passenger side to add more clearance
- Mounts between factory points that hold the sway bar in place
- Raised/longer spacers helps correct the lean of a vehicle and also adds additional rear travel in the back to help clear the sway bar link from the panhard rod at full extension
- Includes front and rear mounts (3 in total)
- See instructional video for how these get installed here
- Installation Instructions
(16 reviews) -
Suspension
Dobinsons Sway Bar Relocation Kit | Tacoma FJ Cruiser GX470 4Runner
- Suits 2005-2023 Toyota Tacoma 4×4 models, 2003-2009 4Runner 4th Gen, 2006-2009 FJ Cruiser, Lexus GX470 (all years without KDSS)
- Lowers the stock front sway bar for better working angle
- Includes machined aluminum spacers
- Easy bolt-on installation
- Includes new correct grade longer hardware
- Recommended for lift heights of 2″ or more
(3 reviews) -
80 Series Land Cruiser (1990-1997)
Dobinsons Front Sway Bar Extension Set for Toyota Land Cruiser 70 and 80 Series
- Toyota Land Cruiser 80 series, only 9/1991 plus models, Lexus LX450, and Also suits LJ78, LJ79, RJ77, KZJ78
- For 2″ to 6″ lift heights
- Zinc plated steel with all hardware supplied
- Simple bolt-on design
- Reduces bushing wear and corrects sway bar angle to function properly
- Sold as a pair, 1 needed per vehicle
(7 reviews) -
80 Series Land Cruiser (1990-1997)
Dobinsons Rear Sway Bar Extensions | Land Cruiser 70 80 Series Bottom Chassis Mount
- Suits Toyota Land Cruiser 78, 79, 80 Series and Lexus LX450
- For 2″ to 5″ lift heights
- Zinc plated steel with all hardware supplied
- Simple bolt-on design
- Sold as a pair, enough for 1 vehicle
- Bolts to the bottom of the frame, not the side like some earlier models
- Check your mounting position before ordering!!
(3 reviews) -
80 Series Land Cruiser (1990-1997)
Dobinsons Rear Sway Bar Extension Kit | Toyota Land Cruiser 70 80 Series Side Chassis Mount
- Suits Toyota Land Cruiser 78, 79, 80 Series and Lexus LX450
- For 2″ to 5″ lift heights
- Zinc plated steel with all hardware supplied
- Simple bolt-on design
- Sold as a pair, enough for 1 vehicle
- For side-frame mounted brackets only
- Verify your rear sway bar is attached to the side of the frame before ordering (the other option is under the frame)
(6 reviews) -
Dobinsons
Dobinsons Adjustable Rear Sway Bar Link Pair | SE59-591
- Suits the rear of Toyota Tundra 2022+, Toyota Sequoia 2023+, Toyota Tacoma 2024+, Toyota Land Cruiser 300 Series 2022+, Lexus GX550, Toyota Land Cruiser 250 Series 2024+
- Order 1 for 1 vehicle (sold as a pair)
- Heavy Duty, zinc plated, with high quality ball joint ends for long life
- Kit includes 2 sway bar links, everything as shown in the photo, enough for 1 vehicle
- Adjustable length to suit lift heights of 1″ to 4″
- Watch a video here to see more about how this style of link adjusts: https://youtu.be/lZACSaE2PHI
- Photo is of the product installed on a 2022 Tundra
(5 reviews) -
Caster and AlignmentFREE SHIPPING
within 48 US StatesHeavy Duty Adjustable Toyota Front Sway Bar Links | Tacoma 4Runner FJ GX470 GX460
- Suits 2005-23 Tacoma, 2003-24 4Runner, GX470 and GX460 and FJ Cruiser (will not suit any KDSS models)
- Factory sway bar links are prone to bending and breaking and can even puncture your CV boots
- All-Pro’s heavy-duty sway bar links replace the weak stock links
- Uses Top quality Teflon lined 3/4″ Heim Joints
- Made from Hefty .156 wall DOM tubing
- Adjustable length to set sway bar angle correctly
- You can lubricate the heims once a month to help them last longer and prevent rust with a silicone spray such as PB Blaster or
WD 40 - Installation Instructions
(10 reviews) -
Suspension
Front KDSS Spacer – Lexus GX460 5th Gen 4Runner
- Front single spacer with hardware only
- Suits 5th Gen Toyota 4Runner with KDSS (2010-2024) and Lexus GX460 (2010-2023)
- Made from 6061 aluminum, Type III hard coat anodized in black, and supplied with new hardware
- Helps correct incessant lean of a lifted vehicle with KDSS by adding a front spacer
- Bolt on installation
- May require modification of a factory skid plate to clear the sway bar link at full droop
- Mounts between factory points that hold the sway bar in place
- Raised/longer spacers helps correct the lean of a vehicle and also adds additional rear travel in the back to help clear the sway bar link from the panhard rod at full extension
- Includes 1 x front mount with hardware
- See instructional video for how these get installed here
- Installation Instructions
- A full kit including the single front spacer is also offered HERE
(16 reviews) -
Ranger 2019+ (US Spec)
Dobinsons Front Sway Bar Link Set | Ford Ranger USA Model 2019-2023
- For Ford Ranger 2019-2023 USA Spec models
- Use with Dobinsons lift heights of 1.75″ or more
- Black with all hardware supplied
- Simple bolt-on design
- Fixed length, 290mm (11.42″) from center to center of ball joints
- Reduces bushing wear and corrects sway bar angle to function properly
- Prevents sway bar from contacting where it shouldn’t when running longer travel struts, like Dobinsons
- Sold as a pair, 1 needed per vehicle
(3 reviews) -
Suspension
Apache Offroad HD Chromoly Rear Adjustable Sway Bar Links | 4Runner FJ Cruiser GX470 GX460
- Suits 4th and 5th Gen 4Runner 2003-2024, FJ Cruiser (all years), GX470, GX460 (without KDSS)
- Order 1 for 1 vehicle
- Adjustable (on vehicle) from 165mm – 206mm – Suits standard and long travel rear lifts
- Custom Forged Oversized (22mm ball) Chromoly Rod End / Joints
- Premium Silicone Dust Boots
- High Carbon Steel Center Link
- Black EDP Coating for corrosion resistance
- High Quality Polyurethane Bushings on frame side
- Serrated Oval / Distorted Thread Locking Nut – The factory sway bar material expands and contracts as you drive, thus causing the nut to come loose and the sway bar link to disconnect. This is not ideal. This style nut, is the best solution we have found to the issue, though we do still recommend the use of thread locker at install
- Mounting hardware included
- Rod end machined to accept hex key to prevent the rod end from spinning during installation. Other brands come with a nut on the inner side of the shaft, which is harder to use and more likely to cause you to tear the boot upon installation
- Sold as a pair
- Maintenance Free Design
- 2 year unlimited mile warranty
(10 reviews) -
Suspension
Apache Offroad HD Chromoly Front Adjustable Sway Bar Links | 4Runner FJ GX470 GX460 Tacoma
- Suits 4th and 5th Gen 4Runner 2003-2024, FJ Cruiser (all years), GX470, GX460 (without KDSS) and Tacoma 2005-2023
- Order 1 for 1 vehicle
- Adjustable (on vehicle) from 140mm – 180mm – Suits stock or lifted vehicles.
- Custom Forged Oversized (22mm ball) Chromoly Rod End / Joints
- Premium Silicone Dust Boots
- High Carbon Steel Center Link
- Black EDP Coating for corrosion resistance
- Serrated Oval / Distorted Thread Locking Nut – The factory sway bar material expands and contracts as you drive, thus causing the nut to come loose and the sway bar link to disconnect. This is not ideal. This style nut, is the best solution we have found to the issue, though we do still recommend the use of thread locker at install
- Mounting hardware included
- Rod end machined to accept hex key to prevent the rod end from spinning during installation. Other brands come with a nut on the inner side of the shaft, which is harder to use and more likely to cause you to tear the boot upon installation
- Sold as a pair
- Maintenance Free Design
- 2 year unlimited mile warranty
(10 reviews) -
Dobinsons
Dobinsons Extended Jeep JL JT Front Sway Bar Link Kit | Gladiator JT Wrangler JL
- Fits Jeep Gladiator JT 2020+ and Jeep Wrangler JL 2018+ 2-door and 4-door
- Recommended for a Jeep with 2″ of lift
- Required for a Jeep with 3″ of lift
- Heavy Duty design with high quality ball joint ends for long life
- Fits and installs the same as OEM, but with added length so that the stock sway bar still functions normally at a lifted height without reducing wheel travel
- Sold as a pair, enough for 1 vehicle
(6 reviews) -
Suspension
KDSS Spacer Kit – Lexus GX460 5th Gen 4Runner – Rears Only
- Rear spacers only (2 rear spacers included with hardware)
- Suits 5th Gen Toyota 4Runner with KDSS (2010-2024) and Lexus GX460 (2010-2023)
- Made from 6061 aluminum, Type III hard coat anodized in black, and supplied with new hardware
- Helps correct incessant lean of a lifted vehicle with KDSS by adding a spacers to both mounts on the rear
- Bolt on installation
- Mounts between factory points that hold the sway bar in place
- Raised/longer spacers helps correct the lean of a vehicle and also adds additional rear travel in the back to help clear the sway bar link from the panhard rod at full extension
- Includes rear mounts (2 in total)
- See instructional video for how these get installed here
- Installation Instructions
- A full kit including the single front spacer is also offered HERE
(16 reviews) -
Gladiator JT (2020-2024+)
Dobinsons SE29-575 Rear Extended Sway Bar Link Kit | Jeep Gladiator
- Fits Jeep Gladiator JT 2020+
- Recommended for a Jeep with 2″ of lift
- Required for a Jeep with 3″ of lift
- Heavy Duty design with high quality ball joint ends for long life
- Fits and installs the same as OEM, but with added length so that the stock sway bar still functions normally at a lifted height without reducing wheel travel
- Sold as a pair, enough for 1 vehicle
(4 reviews) -
Rusty's Off RoadFREE SHIPPING
within 48 US StatesRusty’s Forged Adjustable Sway Bar Quick Disconnects | TJ LJ XJ MJ ZJ
- Suits the following Jeep models
- 1997-2006 TJ Wrangler
- 2003-2006 LJ Unlimited
- 1984-2001 XJ Cherokee
- 1986-1993 MJ Comanche
- 1993-1998 ZJ Grand Cherokee
- 1997-2006 TJ Wrangler
- Forged ends with Grade 8 and stainless steel hardware
- Adjustable from 2″ to 8.5″ of lift; no removal needed for adjustment
- Provides an easy way to connect / disconnect the front sway bar
- Includes bolt-on frame side retention brackets that allow you to hold the links up when sway bar links are disconnected.
- Hardware is included for all models, upgrade vehicles and never buy another set of disconnects!
- Built in Rainbow City, Alabama, USA
(7 reviews) - Suits the following Jeep models
-
Suspension
Apache Offroad HD Chromoly Adjustable Sway Bar Links | 3rd Gen 4Runner
- Suits 3rd Gen Toyota 4Runner 1996-2002, Prado 90 Series, Front or Rear
-
Suits Toyota Land Cruiser Prado 90 and 95 Models RZJ90, VZJ90, KZJ90, KDJ90, RZJ95, VZJ95, KZJ95, KDJ95
- Order 1 for 1 vehicle
- Adjustable (on vehicle) from 165mm – 206mm – Requires at least 1″ of lift if used in the front and 2″ in the rear.Â
- Custom Forged Oversized (22mm ball) Chromoly Rod End / Joints
- Premium Silicone Dust Boots
- High Carbon Steel Center Link
- Black EDP Coating for corrosion resistance
- High Quality Polyurethane Bushings on frame side
- Serrated Oval / Distorted Thread Locking Nut – The factory sway bar material expands and contracts as you drive, thus causing the nut to come loose and the sway bar link to disconnect. This is not ideal. This style nut, is the best solution we have found to the issue, though we do still recommend the use of thread locker at install.
- Mounting hardware included
- Rod end machined to accept hex key to prevent the rod end from spinning during installation. Other brands come with a nut on the inner side of the shaft, which is harder to use and more likely to cause you to tear the boot upon installation.
- Sold as a pair
- Maintenance Free Design
- 2 year unlimited mile warranty
(10 reviews) -
Rusty's Off RoadFREE SHIPPING
within 48 US StatesRusty’s Forged Adjustable Sway Bar Quick Disconnects | JK Wrangler
- Fits: 2007-2018 JK Wrangler and Unlimited
- Forged ends with Grade 8 and stainless steel hardware
- Adjustable from 2″ to 8.5″ of lift; no removal needed for adjustment
- Provides an easy way to connect / disconnect the front sway bar
- Includes bolt-on frame side retention brackets that allow you to hold the links up when sway bar links are disconnected.
- Hardware is included for all models, upgrade vehicles and never buy another set of disconnects!
- Built in Rainbow City, Alabama, USA
(5 reviews) -
Rusty's Off RoadFREE SHIPPING
within 48 US StatesRusty’s Forged Adjustable Sway Bar Quick Disconnects | JL Wrangler + JT Gladiator
- Fits: 2018-Current Jeep JL Wrangler and 2020-Current Jeep JT Gladiator Models with 2.0-6.5″ of lift
- Forged ends with Grade 8 and stainless steel hardware
- Adjustable from 2″ to 6.5″ of lift; no removal needed for adjustment
- Provides an easy way to connect / disconnect the front sway bar
- Includes bolt-on frame side retention brackets that allow you to hold the links up when sway bar links are disconnected.
- Hardware is included for all models, upgrade vehicles and never buy another set of disconnects!
- Built in Rainbow City, Alabama, USA
(10 reviews) -
Dobinsons
Dobinsons Extended JL Rear Sway Bar Link Kit | Jeep Wrangler JL
- Fits Jeep Gladiator JT 2018+ and Jeep Wrangler JL 2018+ 2-door and 4-door
- Recommended for a Jeep with 2″ of lift
- Required for a Jeep with 3″ of lift
- Heavy Duty design with high quality ball joint ends for long life
- Fits and installs the same as OEM, but with added length so that the stock sway bar still functions normally at a lifted height without reducing wheel travel
- Sold as a pair, enough for 1 vehicle
(5 reviews)
