Your cart is currently empty!
Shop
Showing 811–840 of 1944 resultsSorted by popularity
-
Leaf Springs - Tacoma 3rd GenFREE SHIPPING
within 48 US StatesAll Pro 2005-2023 3.0″ Tacoma Leaf Springs Pair – Expedition 2.0 1000LBS
- Suits 2005-2023 Toyota Tacoma 4×4 Models
- Expedition Version 2.0 Leaf Springs give 3.0″ of lift with 1000LBS of added constant load, less lift with more weight
- Number of leaves 9+1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 54-3/8″ (1381 mm)
- Spring Rate: 248lbs/in
- A higher number of thinner leafs provides a smoother, progressive spring rate compared to fewer, thicker leaves.
- Number of Leaves: 9 + 1 Overload/Rebound
- Double “military” wrap provides extra strength for the main leaf
- Eyelet-to-Eyelet Length (Free): 54-3/8″ (1381 mm)
- “Torque Leaf”, an extra half-leaf at the top of the spring pack, increases anti-wrap properties without hindering travel or ride quality.
- Diamond-cut leaf ends to eliminate stress points which may weaken leafs and lead to premature failure
- Teflon anti-friction pads between leafs provide smoother flex, lessen spring wear and reduce noise
- Leafs are shot-peened after forming to relieve stress.
- Every completed spring pack is pre-cycled to their travel extremity for quality control and to reduce the likelihood of initial sag.
- All-Pro leaf springs are sold in pairs, with a complete urethane bushing and sleeve kit.
- Spring Rate: 151 lbs/in for Standard, 207 lbs/in for Expedition, and 248 lbs/in for Expedition 2.0 Leaf Springs
- After installation, the stock rear bumps will no longer be sufficient to prevent the spring from inverting. You must purchase and install a set of bump stops that are of sufficient height to prevent the spring from going negative arch. For best results, we recommend Wheeler’s SuperBumps (sold separately). WOR-306957
- 4″ Extended brake lines – recommended at this lift height
- Requires a suitable 3″ lift shocks to go with them, such as IMS59-50941 or MRA59-A941
- Sold in Pairs
- Made in USA
(7 reviews) -
All Pro OffroadFREE SHIPPING
within 48 US States2005-2023 Tacoma Engine Skid Plate – Raw Aluminum
- Suits 2005-2023 Toyota Tacoma 4×4 Models
- Covers from the front bumper down to the first cross member
- 1/4-inch aluminum construction – Raw aluminum
- Optimal balance between strength and weight
- Save yourself from costly underbody repairs with this easy to install Tacoma skid plate
- Easy, bolt-on installation using all factory hardware
- Compatible with stock bumpers
- Available in 4 variants – Steel or Aluminum, Bare or Powder Coated
- Made in the USA
- Installation Instructions
(7 reviews) -
4Runner 3rd Gen (1996-2002)FREE SHIPPING
within 48 US StatesDobinsons 2-2.5″ 3-Way Adjustable MRA 4Runner Coilovers for 1996-2002
- Suits 1996-2002 Toyota 4Runner 4×4 Models
- Looking for a quick and easy way to lift your 4Runner? This is your answer
- Extended Travel MRA59-A222 Coilovers – 458mm extended, 335mm compressed lengths
- Dobinsons MRA are height adjustable by a fully threaded body
- The Dobinsons MRA Coilovers will come pre-assembled with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- SOLD IN PAIRS – READY TO BOLT IN
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Includes Universal Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
- Instructions for setting coil seat height
- It’s recommended that these coilovers to be run with a diff drop kit and aftermarket UCA’s for coilover clearance and correct travel
- Link to matching rear shocks
- Please NOTE: Assembled coilovers cannot be returned, as they are made to order
(2 reviews) -
Performance Upgrade - 5th Gen 4RunnerFREE SHIPPING
within 48 US StatesPowerbrake D-Line HP Rotor and Pad Kit | 4Runner 10-24 Front
- Suits Toyota 4Runner 5th Gen 2010-2024 Front
- Also available for the REAR
- Powerbrake D-Line Features
- Rotors are cast from a proprietary high carbon cast-iron alloy.
- Rotors are machined to tolerances up to three times tighter than the industry norm.
- All Powerbrake rotors feature our MTR (Max Temperature Recording) system.
- Proprietary black disc surface coating ensures quicker bed-in and max brake performance.
- Spiral slots on the rotor fiction surface clear friction gasses, debris and water.
- Matched high friction PB05 brake pads take the guesswork out of pad selection.
- Pad compound PB05 is manufactured in Japan and has been specifically formulated for use on 4×4 vehicles
- Powerbrake D-Line Benefits at a Glance
- Reduced stopping distances in both wet and dry conditions.
- Reduced brake fade and improved brake consistency.
- Improved initial brake response (bite).
- Improved brake modulation particularly during emergency stops.
- Improved resistance to rotor distortion (warping) and cracking at high temperatures.
- What’s Included in Powerbrake D-Line?
- 2 x Standard OEM diameter high performance slotted rotors for your 4WD or truck – Made in South Africa.
- An axle set of matched PB05 high-performance brake pads – Made in Japan.
- Fits as per a standard rotor and pad change, using the vehicle’s original calipers.
(4 reviews) -
Performance Upgrades - 200 SeriesFREE SHIPPING
within 48 US StatesPowerbrake D-Line HP Rotor and Pad Kit | 200 Series 08-15 Front
- Suits Toyota Land Cruiser 200 Series 2008-2015 Front and Lexus LX570 2008-2015 Front
- Also offered for the REAR
- Powerbrake D-Line Features
- Rotors are cast from a proprietary high carbon cast-iron alloy.
- Rotors are machined to tolerances up to three times tighter than the industry norm.
- All Powerbrake rotors feature our MTR (Max Temperature Recording) system.
- Proprietary black disc surface coating ensures quicker bed-in and max brake performance.
- Spiral slots on the rotor fiction surface clear friction gasses, debris and water.
- Matched high friction PB05 brake pads take the guesswork out of pad selection.
- Pad compound PB05 is manufactured in Japan and has been specifically formulated for use on 4×4 vehicles
- Powerbrake D-Line Benefits at a Glance
- Reduced stopping distances in both wet and dry conditions.
- Reduced brake fade and improved brake consistency.
- Improved initial brake response (bite).
- Improved brake modulation particularly during emergency stops.
- Improved resistance to rotor distortion (warping) and cracking at high temperatures.
- What’s Included in Powerbrake D-Line?
- 2 x Standard OEM diameter high performance slotted rotors for your 4WD or truck – Made in South Africa.
- An axle set of matched PB05 high-performance brake pads – Made in Japan.
- Fits as per a standard rotor and pad change, using the vehicle’s original calipers.
(7 reviews) -
Bronco (2021-2024+)
Dobinsons Ford Bronco Front Coils | C19-562 – Pair
- Dobinsons C19-562 Suits Ford Bronco:
- 2 Door – Base, Big Bend, Black Diamond, Outer Banks WITH 2.3L – with 110-195LB Load
- 2 Door – Base, Big Bend, Black Diamond, Outer Banks WITH 2.7L and Stock Weight
- 4 Door – Base, Big Bend, Outer Banks – Stock Load
- Coil Springs Can Only Be Fitted To Dobinsons IMS19-50098
- Coils Provide Approximately 3″-4″ Lift Above Non Sasquatch Models & 2″-3″ Lift Above Sasquatch Models
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish – Choose what color you would like
- Made in Australia
- Sold in Pairs
(14 reviews)$270.00 Select options This product has multiple variants. The options may be chosen on the product page -
Skid Plates
RCI Tacoma Engine Skid Plate | 2005-2023 Tacoma
- Fits: 2005-2023 Toyota Tacoma
- Protects front two cross-members, low hanging front differential, and oil pan
- Service openings for easy service and oil changes without removal
- Reinforced edges between cross-members for maximum strength and rigidity
- Bolt protector rings surround exposed bolts, shielding against physical damage
- ALL Tacoma front skid plates now come standard with oil filter access door, an essential feature if you have a 2016 or newer truck, and also maintains compatibility on 2005-2015 models
- Smooth, flat surface that easily slides over obstacles
- Black powder coat available for rust resistant, durable and high quality finish
- Utilizes Center mounting points for maximum strength whether steel or aluminum
- Designed to accommodate ALL vehicles with OR without differential drop kits, and does so without compromise.
- Differential cage provides unsurpassed protection, while allowing skid plate to sit tighter to vehicle than competitors
- Installs in minutes
- All hardware and installation instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- MADE IN USA
(3 reviews) -
Skid Plates, Sliders + Racks - Tacoma 3rd Gen
RCI Transmission Skid Plate | Tacoma 2005-2023
- Fits all Toyota Tacoma from 2005-2023
- *Fits 4×4 4.0L/3.5L Access Cab and Double Cab trucks only
- Protects transmission, second and third cross-members
- Excellent addition or replacement of light duty OEM skid plates (which do not provide any coverage of transmission)
- Service openings for maintenance without removal
- Reinforced edges between cross-members for maximum strength and rigidity
- Smooth, flat surface that easily slides over obstacles
- Black powder coat available for rust resistant, durable and high quality finish
- Installs in minutes
- All hardware and installation instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- Compatible with OEM TRD PRO aluminum engine skid plate. No modifications required!
- Finish: Heavy Duty Black Powder Coat or Bare Aluminum
- Made in the USA
(4 reviews) -
270° AwningsFREE SHIPPING
within 48 US StatesOverland Vehicle Systems Nomadic 270LTE Passenger Side 270 Degree Awning
- Passenger Side Mount
- The Overland Vehicle Systems Nomadic 270LTE Awning is the perfect solution for anyone in need of reliable, free-standing shelter.
- Made with quality materials, this awning provides up to 75 square feet of coverage and can be used at a full 270 degrees.
- The Overland Vehicle Systems Nomadic 270LTE Awning is both easy to set up
- The Nomadic 270LTE Awning is supported by 4 integrated drop-down legs, 4 integrated 1″1/8″ tubular heavy-duty rafters supported on a Heavy-Duty Aluminum Frame.
- The Nomadic 270LTE Awning is made from 280G poly cotton rip stop material with heat sealed seams, easily folds, and secures in a 1000g PVC cover.
- This Nomadic 270LTE awning features a universal “L” mounting bracket solution that can be mounted onto a variety of roof racks, making it perfect for your off-road rig.
- The awning comes with a 4-year warranty, ensuring your satisfaction.
(8 reviews) -
YJ Wrangler (1987-1995)FREE SHIPPING
within 48 US StatesKing 4WD Premium YJ Wrangler Soft Top w/ Tinted Windows, w/ Upper Doors
- Suits 1987-1995 Jeep Wrangler YJ 2-door soft top convertibles – full roof with half door windows
- Does not include any framework
- Black Diamond Fabric with 31% smoke colored window tint
- Black Diamond Fabric
- Specification: Two Layer 24oz Marine Grade – Waterproof
- Testing: CFFA, FMVSS & SAE Requirements
- Specification: UV Approved
- Testing: Accelerated Light Aging Test – 1000 Hours
- Window Glass
- Specification: 96g DOT Approved Pressed flexible vinyl, undistorted, won’t shrink or yellow
- Testing: CFFA, FMVSS & SAE Requirements
- Zippers
- Specification: Reinforced nylon self-correcting zippers
- Testing: 50,000 Cycle Test – No bind or drag
- Velcro
- Specification: Industrial Grade Fiber
- Testing: 150 kg (330 lbs.) per square inch
- Seams
- Specification: 135-gauge thread with heat sealed seams, 4-piece thread per inch
- Testing: CFFA, FMVSS & SAE Requirements
- Belt Rails
- Specification: Polyethylene and Anti Cracking
- Testing: CFFA, FMVSS & SAE Requirements
(7 reviews) -
TJ Wrangler (1996-2006)FREE SHIPPING
within 48 US StatesKing 4WD Premium TJ Wrangler Soft Top w/ Tinted Windows
- Suits 1997-2006 Jeep Wrangler TJ 2-door soft top convertibles (not LJ Unlimited)
- Does not include any framework
- Black Diamond Fabric with 31% smoke colored window tint
- Black Diamond Fabric
- Specification: Two Layer 24oz Marine Grade – Waterproof
- Testing: CFFA, FMVSS & SAE Requirements
- Specification: UV Approved
- Testing: Accelerated Light Aging Test – 1000 Hours
- Window Glass
- Specification: 96g DOT Approved Pressed flexible vinyl, undistorted, won’t shrink or yellow
- Testing: CFFA, FMVSS & SAE Requirements
- Zippers
- Specification: Reinforced nylon self-correcting zippers
- Testing: 50,000 Cycle Test – No bind or drag
- Velcro
- Specification: Industrial Grade Fiber
- Testing: 150 kg (330 lbs.) per square inch
- Seams
- Specification: 135-gauge thread with heat sealed seams, 4-piece thread per inch
- Testing: CFFA, FMVSS & SAE Requirements
- Belt Rails
- Specification: Polyethylene and Anti Cracking
- Testing: CFFA, FMVSS & SAE Requirements
- We also sell a full soft top with replacement soft half door uppers as well, click for details
(8 reviews) -
Full Suspension Kits - Tundra 1st GenFREE SHIPPING
within 48 US StatesDobinsons 2-2.5″ 3-Way Adjustable MRA Lift Kit | Tundra 2000-2006
- Suits 2000-2006 Toyota Tundra 4×4 with V8 Engine
- Adjustable height front struts, lift from 2″ to 2.5″
- Choose from no added rear lift, a Quick Ride block kit or Add-A-Leaf (AAL) Kit
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Universal Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Includes 2 Front MRA Struts, 2 Rear MRA Shocks, 2 Front Coil Springs (a pair), and multiple Rear Lift Options
- It’s recommended that these coilovers to be run with a diff drop kit and aftermarket UCA’s for coilover clearance and correct travel and alignment
- The included droop spacer goes on top of the strut, under the first washer, if lifting more than 2.0″ (see attached photo)
(11 reviews) -
GX460 (2010-2023)FREE SHIPPING
within 48 US StatesDobinsons 2-3.5″ Extended Travel Pre-Assembled IMS Coilovers for Lexus GX460
- Suits 2010-2023 Lexus GX460 4×4 Models
- Looking for a quick and easy way to lift your GX460? This is your answer
- Select your desired lift height and spring rate – we’ll take care of the rest!!
- Dobinsons IMS are height adjustable by a fully threaded body
- The Dobinsons IMS Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- Extended Travel – 575mm fully extended, 430mm compressed
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
- Instructions for setting coil seat height
- To run these Extended Travel coilovers, new UCA’s need to be added for proper articulation and correct wheel alignment. A diff drop kit is also recommended to minimize CV binding at full droop
- Click to see Matching rear shocks
- Please NOTE: Assembled coilovers cannot be returned, as they are made to order
(5 reviews) -
Sequoia 3rd Gen (2023-2024+)FREE SHIPPING
within 48 US StatesDobinsons 3-Way Adjustable MRR Sequoia Lift Kit | 2023-2024+ (3-4″)
- Suits 2023-2024+ Toyota Sequoia 4×4 Models
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- A 2023+ Sequoia came with a front ride height 1″ lower than a 2022+ Tundra, so we’re able to offer a 4″ lift on these, which is a 3″ on a Tundra, and still within the limits of the IFS
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Remote Reservoir 3-way adjustable Shocks, Superior Design, thicker walls, longer travel
- Adjust high and low speed compression (HSC and LSC) and rebound adjustment front and rear
- Massive 66mm (2.6″) body size with 60mm pistons front and rear
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen in the external reservoir
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- Does not suit air suspension equipped models
- Coil seat for MRA59-A446 should be set at 175mm (6.87″) from the strut bushing eye
- 3″+ of front lift requires new aftermarket UCA’s for proper alignment and clearance
- If doing a 4″ lift or higher in the front, a diff-drop kit or longer TRD CV-axles are REQUIRED, failure to complete these requirements could cause OE CV-axle failure
- TRD axle shafts: PT362-3432B and PT362-3431B
- Front Installation Instructions
(9 reviews) -
Full Suspension Kits - Frontier D41FREE SHIPPING
within 48 US States2022 Frontier Lift Kit Dobinsons 2-3″ 3-Way Adjustable MRA Kit | Frontier D41 2022+
- Complete Dobinsons MRA 3-Way Adjustable Suspension Kit for your 2022+ Nissan Frontier D41 Truck
- Choose what front and rear lift heights and load ratings you would like, as well as what parts you would like to include
- Nothing is included in the order if you don’t select it from below
- Adjustable height front struts (requires coil to be compressed above the coil seat to adjust height)
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI CNC machined components for precise tolerances
- Parker Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile
- strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Design features include Drawn, tapered and thinned leaf ends
- Manufactured to international quality standards ISO 9001:2008 using premium grade Sup 9 silicon manganese spring steel,
- Anti-Friction inter leaf liners are use to reduce the friction at each leaf end where the load is creates and provides a smoother, quieter ride.
- Photos show a full kit with many parts selected. If you don’t select a part from below, it is not included
(10 reviews) -
All Pro OffroadFREE SHIPPING
within 48 US StatesJeep Gladiator Overland Tailgate Table | 2019+
- The stock tailgate panel is a wasted opportunity that you can easily correct with the All-Pro Off-Road Overland Tailgate Table.
- The All-Pro Off-Road Overland Tailgate Table turns your opened tailgate into a multi-functional platform for all of your overlanding, camping, fishing, and hunting needs.
- The durable food-grade polyethylene cover can be used as a cutting board while supporting your favorite camp stove.
- A slot on the left side and cup-holders on the right side prevent items from rolling away.
- Requiring only basic hand tools, reusing original hardware, and 3-minutes of time, this is one of the easiest modifications you will ever make on your truck and one every Gladiator owner should do.
- Made in 4 different colors and 2 different styles, choose from the divided cutting board configuration, or the smooth configuration with only round cutouts on the end.
- Thickness is right at 1/2″
- Scroll down on the page to see a full product video!!
- Made in the USA, in sunny California!!
(6 reviews) -
Accessories
RCI FJ Cruiser Rock Sliders
- Fits: Toyota FJ Cruiser all years
- Protects rocker panels and doors
- Our sliders utilize a 2″ square main tube which is far stronger than 1.75″ round tube used by competitors
- 1.75″ DOM is now standard on outer rails for uncompromised strength
- Fully gusseted on all legs
- 45 degree mitered main tube ends provide a superior aesthetic appearance as well as more functional design that won’t hang up
- Full length 1/4″ frame plate and guarantees a slider as strong or stronger than anything on the market
- Easily capable of supporting the entire side of truck for lifting with hi-lift, or sliding on rocks
- 5 degree upward angle creates a low profile with maximum ground clearance, while remaining usable as a step
- Direct bolt on addition to existing mounting locations, no drilling required
- Available tread plate for top surface
- Easy install with only basic hand tools
- All hardware provided (grade 5 & 8 where applicable)
- Now comes standard with our signature low profile rear kickout
- Made to order from your selections below
- MADE IN USA
(5 reviews) -
Skid Plates
RCI Catalytic Guards | 2003-24 4Runner / FJ / GX
- REQUIRES RCI TRANSMISSION SKID PLATE FOR INSTALLATION
- Fits: 2003-2024 4Runner, FJ Cruiser (all years), GX470 and GX460 (all years)
- Protects exposed catalytic converters from on and off road debris
- Excellent addition to the RCI Transmission skid to aid in preventing catalytic converter thefts
- Vented design for adequate airflow and heat dissipation
- Smooth, flat surface that easily slides over obstacles
- Installs in minutes
- All hardware and installation instructions provided
- Direct bolt on addition to existing RCI Transmission skid, drilling may be required until manufacturing begins on pre cut out holes on Transmission skid plate
- Designed around the most current RCI transmission skid plate with 2in double bent side flange
- Requires RCI Transmission Skid Plate for installation
(2 reviews) -
200 Series Land Cruiser ARMORED
Dobinsons Front Monster Struts Pair for Armored Land Cruiser 200 Series XHD
- Made for Armored Vehicles ONLY – Level B6 or B7 Armored Toyota Land Cruiser 200 Series
- Mammoth 70mm body housing with a massive volume of high quality German shock oil
- 20mm Diameter heavy duty chrome piston rods
- 45mm Extra Large Pistons
- 4mm Heavy Duty Wall thickness, double the thickness of regular shock walls
- Threaded adjustable spring seat height for adjustment and additional heat dissipation
- 1 piece drop forged lower strut mount for maximum strength
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals, Fuchs German shock absorber oil
- Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- See all suitable armored coil spring options HERE
- Sold in Pairs
(10 reviews) -
Sequoia 3rd Gen (2023-2024+)
Dobinsons C59-853V Rear Coil Springs Pair
- Dobinsons C59-853V Rear Coils for the 2023+ Toyota Sequoia
- Lifts 3″ with 440LBS constant load on a standard model, and 2″ with 440LBS of constant load on a TRD Pro (TRD Pro comes 1″ lifted from the factory)
- This also fits the 2021+ Land Cruiser 300 Series, gives 50mm lift with 280-400KG constant added weight
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
- Variable Rate Coils
- Longer shocks required, the factory shocks are not long enough to run with these coils
- Select from Twin Tube, IMS Monotube or MRA 3-Way Adjustable with Remote Resi
(1 review)$305.00 Select options This product has multiple variants. The options may be chosen on the product page -
Sequoia 3rd Gen (2023-2024+)FREE SHIPPING
within 48 US StatesDobinsons MRA59-A441 2.6″ 3-Way Adjustable Rear Shocks Pair
- Suits 2023+ Toyota Sequoia with 2-3″ of lift using Dobinsons Coils
- Also suits 2021+ Toyota Land Cruiser 300 Series and 2024+ Land Cruiser 250 Series
- 3-way adjustable valving – Adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Specifications – 680mm extended, 422mm compressed
- SOLD IN PAIRS
- Includes Reservoir Brackets and Hardware, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
(15 reviews) -
Full Suspension Kits - Tundra 2nd GenFREE SHIPPING
within 48 US StatesDobinsons 3-Way Adjustable Tundra 2.0″-3.0″ MRA Suspension Kit | 2007-2021
- Suits Toyota Tundra 2007-2021 Models with 5.7L V8 Gas Engine
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment
- Coils are teal. Struts and shocks are black
- Front MRA Coilovers are assembled at the standard coil seat height
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg, EDP Surface Protection
- Requires lower mount clearancing to fit the larger lower leg of the new coilover (see attached photo)
- See attached photo for correct hose routing
- CNC TIG Precision Welded Body End Mounts
- Includes Reservoir Brackets and Hardware and Sticker Pack
- Full 2 year limited warranty, no set rebuild time period, fully rebuildable shocks
- Note about lift heights – all vehicles can have some variance and desired lift height may need to be adjusted to suit your specific vehicle
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Choose your desired suspension parts to build the kit best suited to your weight
- Multiple lift height and load ratings available
- Front coilover assembly instructions
- New UCA’s are required for proper coilover and hose clearance, see all options
- Aftermarket wheels with +18 Offset or less REQUIRED to avoid reservoir + hose rubbing at full lock
(12 reviews) -
Full Suspension Kits - 100 Series
Dobinsons 100 Series lift kit | Toyota Land Cruiser IFS DIESEL 1998-2007 (all shock options)
- Build a full suspension replacement here for your Toyota Land Cruiser 100 Series 1998-2007, with all possible options listed on this one page
- THIS PAGE IS FOR DIESEL ENGINE MODELS ONLY
- Lexus LX470 and Land Cruiser 100 Series share the same suspension parts
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- A base kit includes 2 Front Shocks, Pair Front Torsion Bars, 2 Rear Shocks, and 2 Rear Coil Springs
- You can choose from twin tube, IMS Monotube or MRA 3-Way Adjustable Monotube shocks in the drop down menus
(10 reviews) -
100 Series Land Cruiser IFS (1998-2007)
Dobinsons 100 Series Torsion Bars Pair for DIESEL ONLY
- For DIESEL powered Land Cruisers from 1998 to 2007
- Total length is 1210mm, 34mm bar thickness
- These WILL NOT fit a V8 gas model Land Cruiser, they’re too long
- Increased spring rate to improve handling and lift front end
- Powder coated black for a long lasting finish
- Replaces OE torsion bars without modification
- Torsion bars must be installed with 2/3 suspension down travel and 1/3 up travel to ensure a good ride
- Comes as a set, 1 per vehicle
(2 reviews) -
-
Suspension
Dobinsons SD59-821 Big Bore Steering Damper – Toyota Pickup & 4Runner (1979-1985)
- Suits Pre-1985 Leaf Spring front end Toyota Pickup and Toyota 4Runner 4×4’s
- Induction Hardened Rods for strength, no Viscosity Drop due to High Shear Stability
- Cellular Foam Cell Insert, Teflon Piston Rings
- Excellent Viscosity Temperature Performance
- NOK Triple Lip Oil Seals, High Quality Fuchs German Oil
- Replaces OE steering damper, bolts into place
(3 reviews) -
Ranger 2019+ (US Spec)
Dobinsons L19-132-R Leaf Springs Pair | Ford Ranger 2019+ USA Spec (40mm w/600LBS)
- Suits USA Spec Ford Ranger 2019-2022+
- L19-132-R lift 40mm (1.6″) over stock height with 600LBS of added constant weight – lifts more with less weight
- Pack has 7 leaves
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Design features include Drawn, tapered and thinned leaf ends
- Manufactured to international quality standards ISO9001:2008 using premium grade Sup 9 silicon manganese spring steel,
- Anti-Friction inter leaf liners are use to reduce the friction at each leaf end where the load is creates and provides a smoother, quieter ride.
- These are leaf springs ONLY and don’t come with bushings or any other parts. Scroll down for add-ons that go with these springs
- Photo for illustration purposes only, not of actual part number
(5 reviews) -
BrakesFREE SHIPPING
within 48 US StatesPowerbrake X-Line 4×4 3rd Gen 4Runner Big Brake Kit 1996-2002
1996-2002 3rd Gen 4Runner Big Brake Kit Includes:
- X-Line billet 6-piston off-road calipers (pair)
- High-performance brake pads, pre-loaded into the calipers
- 1-Piece 350mm x 34mm (13.77″ x 1.33″) 48-vane discs
- Curved, directional cooling vanes
- Billet caliper mounting brackets
- Stainless steel braided brake lines
- All necessary mounting hardware for quick, easy bolt-on installation
- Comprehensive fitment and bed-in instructions
- Now Includes Upgraded Powerbrake Pads, PB05 Compound – highest level 4×4 brake pads available – made in Japan
- Manufactured, finished and packaged 100% in South Africa
- Also Suits Toyota Land Cruiser Prado 90 and 95 Models RZJ90, VZJ90, KZJ90, KDJ90, RZJ95, VZJ95, KZJ95, KDJ95
- REQUIRES 17″ WHEELS FOR ADEQUATE CALIPER CLEARANCE
(6 reviews)$2,675.00 Select options This product has multiple variants. The options may be chosen on the product page
