Your cart is currently empty!
Tacoma 3rd Gen (2016-2023)
Showing 121–150 of 195 resultsSorted by popularity
-
Differential | DrivetrainFREE SHIPPING
within 48 US StatesARB RD129 Rear Air Locker Toyota 8.4″ 30 Spline
- For Use only with Toyota 8.4″ 12 Bolt 30 spline Rear Axle
- Suits multiple vehicles, the full list is down below. Used in older Tacoma, Sequoia, Tundra and T100 Trucks.
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
(16 reviews) -
Differential | DrivetrainFREE SHIPPING
within 48 US StatesARB RD121 Front Air Locker Toyota Lexus 8″ IFS 30 Spline 3.73-
- For Use With Toyota 8″ IFS Clamshell differential with 30 Spline Axles and 3.73 And Down Factory Gears
- Usually all models that came with a manual transmission used 3.73- factory gear ratios, but you must check before ordering
- Factory R&P may use either RD111 or RD121 depending on ratio. All known aftermarket R&P sets suit RD121.
- If you are re-gearing, check with the gear manufacturer for which Air Locker to order
- Full vehicle fitment list is further down in the main description, includes 4Runner, Tacoma, FJ Cruiser, GX470, GX460
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
(12 reviews) -
Skid PlatesFREE SHIPPING
within 48 US StatesARB 5423010 Toyota Tacoma Skid Plate Set | 2005-2023 4×4
- Suits all Toyota Tacoma 4×4 models from 2005 to 2023 (2nd and 3rd Gen)
- 3mm pressed and folded sheet steel adds more strength than a standard folded sheet.
- Laser cut sheet steel.
- Zinc plated and powder coated with a silver textured finish.
- Recessed mounting bolts are protected and easy to remove for vehicle servicing.
- The Under Vehicle Protection will fit with or without an ARB front bumper. Fitment has not been confirmed with other aftermarket bumper designs
- Comprises 4 panels: Front Panel (Protects power steering, engine sump, sway bar), Diff Panel (Protects front diff mounts, engine sump), Transmission (Protects transmission and transmission controls) and Transfer Case (Protects transfer case)
- See more details below as well as product video
(11 reviews) -
Rear DrawersFREE SHIPPING
within 48 US StatesOVS Slide Out Bed Extension for 5.0FT Short Bed Trucks
- Suits 5.0FT Short Bed Mid-Size Trucks
- Mid Size Short Bed 5.0′: 57.08″ long x 42.12″ wide x 7.28″ tall
- Potential Vehicle Fitments (Measure your truck bed first!!): Tacoma, Frontier, Gladiator, Ranger, Hilux, Colorado
- These are made in 3 different sizes. Mid-Size Truck 5.0Ft Long, Full Size Truck 5.5FT Long and Full Size Truck 6.5FT Long
- 75% Extension Bed Cargo Slide
- 1250 LBS. Max Load Capacity
- Steel Frame Construction
- 304 Stainless Steel Hardware
- Single Pull Latch for Easy Operation
- Multiple Anchor Points for Cargo Security
- Great for camping, easily slide out all your gear
- Excellent for work use, keep your tools and heavy objects organized, then slide them out easily to reach them
- Perfect for people with truck caps or canopies, easier to reach the parts out of the truck
- Some photos show the different sized models
(0 reviews) -
Dobinsons
Dobinsons Single Caster Wedge 60MM Wide – 3 Degrees
- 3 Degree Caster shim can be used to correct front caster / pinion angle or rear pinion angle on a 60mm wide leaf spring
- Sold individually
- Suits the following Dobinsons leaf spring part numbers:
- 106-4+3-R
- 106-5+3-R
- B2600-4X4-R
- DAI-009-F
- DAI-011-R
- DAI-015-R
- DAI-020-F
- DAI-021-R
- F77-5+2-R
- F77-5L-F
- HIL-001-F
- HIL-002-F
- HIL-003-F
- HIL-006-R
- HIL-010-F
- HIL-034-R
- HIL-035-R
- HIL-4+2-R
- HIL-5+2-R
- L19-131-R
- L19-132-R
- L19-133-R
- L21-140-R
- L21-141-R
- L21-142-R
- L39-030-R
- L39-031-R
- L39-032-R
- L45-002-R
- L45-003-R
- L45-004-R
- L45-151-R
- L45-152-R
- L45-153-R
- L45-154-R
- L59-040-R
- L59-041-R
- L59-042-R
- L59-110-R
- L59-111-R
- L59-112-R
- L59-120-R
- MAZ-003-R
- MK-6L-F
- MK-7L-F
- MQ-6L-F
- MQ-7L-F
- MQ-UTE-R
- MQ-WAG-R
- NAV-005-R
- NAV-4WD-R
- NIS-260-F
- RODE-008-R
- RODE-011-R
- RODE-012-R
- RODE-013-R
- TOY-470-R
- UAZ-004-R
- UAZ-006-R
(0 reviews) -
Trail-Gear
Longfield IFS +3.5″ CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- +3.5″ length for use on +3.5″ long travel kits (cannot be used with stock lower control arms)
- Longfield IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- 35-spline CV Joint stars & axle shafts.
- Available in direct stock replacement versions & long-travel versions.
- CV Joints housings are 100% SAE 4340 Chromoly Steel.
- Double-offset inboard CV joint with 1-inch diameter all bearings.
- SAE 4340 Chromoly Steel axle shafts with black powder-coat finish.
- 300M internal components.
- Proprietary elastomer boot material for enhanced puncture & tear resistance.
- Wear-Resistant 52100 Alloy Steel Bearing Balls.
- All Components Precision Polished to Remove Imperfections and Prevent Stress Risers.
- CV Joints Black Oxide & Powder-Coat Finish for Corrosion Resistance.
- CV Joints are pre-lubricated with racing-grade Red Line CV-2 Moly Grease
- Includes IFS axle spindle nuts.
- Sold as a pair
- Made in the USA
- Installation Guide
(0 reviews) -
Trail-Gear
Longfield IFS +2.75″ CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- +2.75″ length for use on +2.75″ long travel kits (cannot be used with stock lower control arms)
- Longfield IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- 35-spline CV Joint stars & axle shafts.
- Available in direct stock replacement versions & long-travel versions.
- CV Joints housings are 100% SAE 4340 Chromoly Steel.
- Double-offset inboard CV joint with 1-inch diameter all bearings.
- SAE 4340 Chromoly Steel axle shafts with black powder-coat finish.
- 300M internal components.
- Proprietary elastomer boot material for enhanced puncture & tear resistance.
- Wear-Resistant 52100 Alloy Steel Bearing Balls.
- All Components Precision Polished to Remove Imperfections and Prevent Stress Risers.
- CV Joints Black Oxide & Powder-Coat Finish for Corrosion Resistance.
- CV Joints are pre-lubricated with racing-grade Red Line CV-2 Moly Grease
- Includes IFS axle spindle nuts.
- Sold as a pair
- Made in the USA
- Installation Guide
(0 reviews) -
Trail-Gear
Longfield IFS +2.00″ CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- +2.00″ length for use on +2.00″ long travel kits (cannot be used with stock lower control arms)
- Longfield IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- 35-spline CV Joint stars & axle shafts.
- Available in direct stock replacement versions & long-travel versions.
- CV Joints housings are 100% SAE 4340 Chromoly Steel.
- Double-offset inboard CV joint with 1-inch diameter all bearings.
- SAE 4340 Chromoly Steel axle shafts with black powder-coat finish.
- 300M internal components.
- Proprietary elastomer boot material for enhanced puncture & tear resistance.
- Wear-Resistant 52100 Alloy Steel Bearing Balls.
- All Components Precision Polished to Remove Imperfections and Prevent Stress Risers.
- CV Joints Black Oxide & Powder-Coat Finish for Corrosion Resistance.
- CV Joints are pre-lubricated with racing-grade Red Line CV-2 Moly Grease
- Includes IFS axle spindle nuts.
- Sold as a pair
- Made in the USA
- Installation Guide
(0 reviews) -
Trail-Gear
Longfield IFS CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- Standard/Stock length for use on lifted and non-lifted applications
- Longfield IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- 35-spline CV Joint stars & axle shafts.
- Available in direct stock replacement versions & long-travel versions.
- CV Joints housings are 100% SAE 4340 Chromoly Steel.
- Double-offset inboard CV joint with 1-inch diameter all bearings.
- SAE 4340 Chromoly Steel axle shafts with black powder-coat finish.
- 300M internal components.
- Proprietary elastomer boot material for enhanced puncture & tear resistance.
- Wear-Resistant 52100 Alloy Steel Bearing Balls.
- All Components Precision Polished to Remove Imperfections and Prevent Stress Risers.
- CV Joints Black Oxide & Powder-Coat Finish for Corrosion Resistance.
- CV Joints are pre-lubricated with racing-grade Red Line CV-2 Moly Grease
- Includes IFS axle spindle nuts.
- Sold as a pair
- Made in the USA
- Installation Guide
(0 reviews) -
Steering Upgrades
Power Flow Land Cruiser 200 Series Steering Rack – All New
- Direct replacement for Toyota OEM Part Number 44200-60170 for Land Cruiser 200 Series and Lexus LX570 5.7L V8 2008-2021
- High-quality LC200 OEM-style Replacement
- Brand New Rack, NOT rebuilt
- No core charge and no return shipping of the old unit required
- Largest & strongest Toyota-size steering rack
- Has 3rd rack mount that Tacoma or Tundra racks do not have.
- High-temperature seals
- M22-1.5 Threaded Tie Rod ends
- Can be used as an OEM replacement or as part of the All Pro +3.50″ Modular Long Travel Kit or similar
- Adaptation is required for this to fit Tacoma, 4Runner, GX470, GX460 and FJ Cruiser – that adaptation comes with the long travel kit (sold separately)
- Includes only what is in the photos
(0 reviews) -
Apache Offroad
Apache Offroad AX2 IFP Rear Shocks Pair | 2005-2023 Tacoma 00-06 Tundra
- Suits Toyota Tacoma 2nd and 3rd Gen, 2005-2023, and Toyota Tundra 1st Gen 2000-2006
- Suits 0-3″ of lift
- Direct Bolt on Installation
- Includes upper bushings and washers, and lower bushings already pressed in
- Includes shock boots to protect the shock shaft
- Proprietary high-Zinc content paint coating for superior protection against rock chips and abrasion damage
- Nitrogen Charged Monotube Design
- Internal Floating Piston- Separates the oil and nitrogen to prevent shock fade
- Fully rebuildable and revalveable
- Linear Valving
- Hardened Chrome Piston shaft- resists rock damage and corrosion
- Precision Japanese CNC machined, High Flow Piston
- Heavy Duty Ultra Low Friction Japanese 3 Stage Seal System
- High Quality German Oil
- Heavy Duty Lower Leg
- Hardened Rubber Lower Bushing provides a long and quiet life
- Heavy Duty 1/8″ (3mm) DOM wall thickness
- 2 Year Warranty
- 379mm Compressed, 614mm Extended
- SOLD IN PAIRS – Includes new washers and bushings for the top, and lower bushings are pressed in
(10 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesApache Offroad Assembled Tubular UCA Pair | Tacoma 2005-2023
- Suits Toyota Tacoma from 2005 to 2023
- Complete assembled kit for both left and right hand side, includes new Moog ball joints, ball joint caps, rubber frame bushings
- Has 3 degrees of caster built in, no adjustability or settings required
- Has more clearance around the ball joint than factory UCA’s for better tire clearance
- Manufactured from Black Powder coated 1.5″ Steel Tube
- The Apache UCAs Feature Hardened Rubber Bushings for a quiet ride
- Comes assembled with OE sized Greaseable Moog Problem Solver Ball Joints
- Includes Machined Aluminum Dust Covers with dust seals
- Works for any lift height of 2.0″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Do not forget to grease your ball joints 🙂 They do not come pre-greased.
- Product Video
(10 reviews) -
Upper Control Arms
SPC 35101 Replacement Ball Joint Set for 25470 25540 25560 25660
- Replaces Ball Joint on SPC Arms – 25470, 25540, 25560, 25660
- Will not work on OEM or any other brand aftermarket upper control arms (UCA’s)
- Suits Toyota Tacoma 2005-2023 4×4 and Prerunner
- Suits Nissan Frontier 2005-2021, Nissan Frontier 2022+, Nissan Navara 2005-2020. Nissan NP300 2016+, Nissan Xterra (2005-2015), Nissan Pathfinder R51 2005 to 2012
- Nissan Titan and Armada
- Ford Ranger T6
- Sold in Pairs
- Fully seated boot to keep grease in and contaminants out for a maintenance-free joint
- High strength steel forging with offsets provides camber & caster adjustability
- One piece polymer race tests like OE and provides low & smooth turning torque
- Oversized ball generates 80˚ of articulation with a 25% increase in neck cross section vs. OE for added strength
- Modern grease formula ensures quiet and smooth operation with reduced wear for extended life
- Extended threads on ball stud will work with most popular spindle gusset kits
- These ball joints are reverse compatible and a direct replacement for the SPC upper control arm sets
- Installation Instructions
(10 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King Toyota Tacoma Billet UCA’s Pair for 2005-2023
- Suits 2005-2023 model Toyota Tacoma 2nd and 3rd Gens – 6 Lug models only
- CAD designed
- Precision-machined from 6061 aluminum for strength and durability
- Improved caster settings for enhanced handling
- Re-engineered pivot angles for increased articulation
- Adjustable inner pivot system for camber and caster adjustments
- Maintenance-free SilentSpin bushings for smooth, quiet operation
- Optional ¾” chromoly rod ends for firm, performance-driven handling
- Heavy-duty Probearing ball joints for long-lasting durability
- Fully rebuildable and replaceable components for easy maintenance
- Compatible with Dirt King shocks for increased lift and suspension travel
- Proudly made in the USA
(0 reviews) -
Full Suspension Kits - Tacoma 3rd GenFREE SHIPPING
within 48 US StatesFront +2″ Tacoma Long Travel Kit | Toyota Tacoma 2005-2023
- Suits Toyota Tacoma 2005-2023 2WD and 4WD
- Adds 2.0″ of width to either side for a total of 4″ total track width added!!!
- 4WD requires long travel axle shafts or full axle assemblies
- 2” Wider Per Side: Adds 2” of width per side, boosting suspension travel by 25%.
- Stock Fender Compatibility: Works with stock fenders when using positive offset wheels.
- Aggressive Look Option: Supports zero or negative offset wheels with flared fenders.
- Extended Wheelbase: Allows proper fitment of 35” tires.
- SilentSpin Bushings: Greaseless bushings in upper control arms for low maintenance.
- Delrin Bushings with PTFE: Smooth operation in lower control arms with PTFE-infused Delrin.
- Heavy-Duty Moog Ball Joints: Reliable outer pivots with heavy-duty Moog ball joints.
- Aluminum Skid Plates: Replaceable skid plates protect lower arms on rough trails.
- Flexible Installation: Compatible with coilovers, coilovers with bypasses, or coilovers with bump stops.
- Aluminum Strike Pads: Designed for optimal bump stop engagement.
- Complete Hardware Included: Comes with all necessary mounting hardware.
- Made in the USA: Proudly designed and manufactured in the United States.
- What’s Included:
- Boxed plate upper control arms
- Boxed plate lower control arms
- 8″ quad wrapped limit straps
- Weld on adjustable limit strap mounts
- 17-4 stainless steel tie rod extensions
- DOT approved extended brake lines
- Grade 8 mounting hardware
- Billet aluminum bump stop strike pad
- Zinc plated bushing washers
- No coilovers or bump stops are included!!
- Installation instructions for 2005-2015 and 2016-2023
(0 reviews) -
Replacement Bushings
Dobinsons Lower Shock Bushing – For -941
- Dobinsons replacement lower shock bushing
- Suits Dobinsons shock part number IMS59-50941 and MRA59-A941
- Full list of part numbers this fits is below
- This is for a single bushing only for 1 shock
- High quality natural rubber bushing
- Photo is of actual bushing
- These do not suit GS59-940, IMS59-50940 or MRA59-A940, those use a different size bushing
(0 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.5 Tacoma DCA Remote Resi Shocks | 2005-2023
- Suits Toyota Tacoma 2005-2023 4×4 and Prerunner
- Suits up to 1.5″ of lift
- Dual Compression Adjuster (DCA) is on the resi to fine tune the ride quality
- Dual Compression Adjusters with 10 adjustments for each knob
- Increased suspension travel
- Specific valving for each vehicle providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Remote reservoir equipped with dual compression adjusters allowing for high-speed and low-speed compression adjustments
- Less seal drag with the 3/4″ shafts compared to traditional 7/8″ shafts resulting in smoother operation
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2.5″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 3/4″ shafts
- What’s Included:
- 2.5 DCA shocks with remote reservoirs Pair
- Shock shaft boots
- Reservoir mounts
- All necessary mounting hardware
- Installation instructions
- Matching Front Coilovers
(4 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.5 Tacoma DCA Remote Resi Coilovers | 2005-2023
- Suits Toyota Tacoma 2005-2023 4×4 and Prerunner
- Comes preset to 2.5″ of lift
- Dual Compression Adjuster (DCA) is on the resi to fine tune the ride quality
- Dual Compression Adjusters with 10 adjustments for each knob
- Increased suspension travel
- Specific valving for each vehicle providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Remote reservoir equipped with dual compression adjusters allowing for high-speed and low-speed compression adjustments
- Less seal drag with the 3/4″ shafts compared to traditional 7/8″ shafts resulting in smoother operation
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Cold wound, high-tensile alloy steel coil springs that retain consistent rate and ride height
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2.5″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 3/4″ shafts
- Provides up to 3” of lift | Must be paired with aftermarket UCA
- Note: We do not recommend lifting the vehicle more than 3″. Excessive preload will reduce the ride quality
- What’s Included:
- 2.5 DCA coilover shocks with remote reservoirs Pair
- Coils installed are 14” long, 700 LBF/in Spring Rate
- Sway bar relocation mounts with reservoir brackets
- Spanner wrench
- All necessary mounting hardware
- Installation instructions
- Installation video is down below
- Matching Rear Shocks
(4 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.0 IFP Tacoma Mid Travel Package | Tacoma 2005-2023
- Suits Toyota Tacoma 2005-2023 4×4 and Prerunner
- Includes preassembled front Coilovers, Rear Shocks, and preassembled UCA’s
- Front comes preset to 2.5″ of lift with stock weight
- Increased suspension travel
- Vehicle specific valving providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Cold wound, high-tensile alloy steel coil springs that retain consistent rate and ride height
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 5/8″ shafts
- Provides up to 3” of front lift, rear shocks suit 1.5″ of lift
- Note: We do not recommend lifting the vehicle more than 3″. Excessive preload will reduce the ride quality
- What’s Included:
- 2.0 Dirt King IFP Series coilovers Pair
- Coils installed are 14” long, 700 LBF/in Spring Rate
- 2.0 Dirt King IPF Smooth Body Rear Shocks Pair
- Dirt King Tubular Ball Joint UCA’s
- Sway bar relocation mounts
- Spanner wrench to adjust height/preload
- All necessary mounting hardware
- Installation instructions
(7 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.0 IFP Smooth Body Shocks Pair | Tacoma 2005-2023
- Suits Toyota Tacoma 2005-2023 2WD and 4WD
- Allows for up to 1.5″ lift
- Increased suspension travel
- Vehicle specific valving providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 5/8″ shafts
- What’s Included:
- 2.0” IFP smooth body shocks Pair
- Shock shaft boots
- All necessary mounting hardware
- Installation instructions
- Matching front coilovers
(4 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King 2.0 IFP Tacoma Coilovers Pair | Tacoma 2005-2023
- Suits Toyota Tacoma 2005-2023 4×4 and Prerunner
- Comes preset to 2.5″ of lift with stock weight
- Increased suspension travel
- Vehicle specific valving providing optimal ride comfort
- Aluminum body for cooler operation and corrosion resistance
- Direct bolt-on replacement that uses factory shock mounting location
- Maxima custom oil blend. The proprietary light viscosity semi-synthetic oil blend is low friction and extremely resistant to high operating temperatures
- Cold wound, high-tensile alloy steel coil springs that retain consistent rate and ride height
- Completely rebuildable and serviceable. All tools and replacement parts can be purchased from Dirt King
- 2″ hard-anodized 6061 aluminum bodies
- Progressive valving
- Internal floating piston
- Induction-hardened 5/8″ shafts
- Provides up to 3” of lift | Must be paired with aftermarket UCA
- Note: We do not recommend lifting the vehicle more than 3″. Excessive preload will reduce the ride quality
- What’s Included:
- 2.0 Dirt King IFP Series coilovers Pair
- Coils installed are 14” long, 700 LBF/in Spring Rate
- Sway bar relocation mounts
- Spanner wrench to adjust height/preload
- All necessary mounting hardware
- Installation instructions
(4 reviews) -
Full Suspension Kits - Tacoma 3rd GenFREE SHIPPING
within 48 US StatesFront Tacoma Long Travel Kit | Toyota Tacoma 2005-2023
- Suits Toyota Tacoma 2005-2023 2WD and 4WD
- Adds 3.5″ of width to either side for a total of 7″ total track width added!!!
- 4WD requires long travel axle shafts or full axle assemblies
- Wheel Travel Specs, Tire Size and Shock recommendations are down below
- Bolt on application, minimal modifications required
- Utilizes American made FK bearings
- 4130 chromoly uniball cups
- Choice of ¾” heims or poly bushings for the UCA’s
- Delrin bushings for the LCA’s
- Zinc plated inner bushing sleeves
- Grease fittings for easy servicing
- 3/16″ and 1/8” boxed plate construction
- Internally ribbed with extrusions for weight reduction
- Bump stop plating
- Limit strap tabbing
- Bypass Tabbing
- To achieve the full amount of travel on 4WD models you must install a 1” diff drop kit and machine the inner CV’s for more articulation
- MADE IN THE USA
(7 reviews) -
Sale!Overland Vehicle Systems (OVS)FREE SHIPPING
within 48 US StatesLD TACT Truck Bed Tent – Mid-Size Truck 5.0FT Bed
- For Mid-Size Truck Beds measuring 5.0-5.2 FT in length
- For Vehicles such as Chevy Colorado, Ford Ranger, GMC Canyon, Nissan Frontier, Toyota Tacoma
- 2-3 Person Design with Spacious Interior and Headroom
- Perimeter Skirt and Reinforced Floor Keeps Truck Bed Dry
- Color Coated Poles for Quick Deployment
- Large Windows with Mesh Allows for Ventilation
- Premium 420D Material with Removable Rainfly
- Padded Elastic Anchor Points for Easy Scratch-Free Fit
- Compact Carrying Bag is Included
- Internal Storage Options
- Setup Instructions
- This truck bed tent style is made in 3 sizes, 5FT, 5.5FT and 6.0FT Truck Beds
(3 reviews) -
RCV AxlesFREE SHIPPING
within 48 US StatesRCV Ultimate IFS CV Axle Set | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits Toyota FJ Cruiser 2007-2014, 4Runner 2003-23, Tacoma 2005-2023, Lexus GX460 2010-2023 & Lexus GX470 2003-2009
- Standard length for use on lifted and non-lifted applications
- RCV Ultimate IFS CV Axles for Independent Front Suspension are designed to overcome the limitations of Toyota FJ Cruiser, 4 Runner, Tacoma, Lexus GX460 and Lexus GX470 IFS axle shafts
- Ultimate IFS CV Axles provide increased strength that original equipment axle shafts just can’t match
- Even if you have big tires and big power there are no worries
- Ultimate IFS CV Axles are low maintenance, and are backed with a “No Questions Asked” limited lifetime warranty against breakage
- Warranty Form
- Our IFS CV axles meet and exceed the strength of a straight axle swap, while allowing you to maintain the traction, smoothness and control of your IFS
- The axles feature a double-offset inboard CV joint that is comprised by 1-inch balls and 300M internal components
- The outboard CVs utilize our Dana 60 architecture with combination of 4340 & 300M components optimized for maximum strength
- The center bar is 35 spline 300M, the strongest in the industry
- The RCV developed moly SPEC grease is used in the CVs to control heat build-up in even the most extreme use environments
- Black oxide coating is standard
- Sold as a pair
- Made in the USA
(9 reviews) -
DobinsonsETA is late December
Dobinsons UCA Ball Joint for Tacoma Hilux and Fortuner
- Suits Dobinsons UCA’s that fit Toyota Tacoma 2nd and 3rd Gen, Toyota Fortuner 2005-2023, Toyota Hilux 2005-2023
- This ball joint will fit UCA part numbers UCA59-003K, UCA59-203K
- Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Sold individually
- Includes new ball joint, boot, split pin and nut (subject to design changes)
(6 reviews) -
MRA Remote Resi 3-Way Adjustable MonotubeFREE SHIPPING
within 48 US StatesDobinsons 2.6″ 3-Way Adjustable Front Long Travel Coilovers Pair | Toyota & Lexus
- Dobinsons Long Travel Coilovers for the front of Toyota and Lexus Trucks and SUV’s
- Intended to be used on 4th and 5th Gen 4Runners, Lexus GX470 and GX460, FJ Cruisers, and Toyota Tacoma 2nd and 3rd Gens – with all Long Travel Parts Installed (upper and lower arms, axles, custom bump stops, limit straps, etc)
- Includes Different bolt pattern adapters for Top mount plate
- Specifications: 602mm (23.7″) extended, 399 mm (15.7″) compressed, uses 1.5″ long x 1/2″ Bolt for lower mounting
- Pair of Coilover Struts only, no coils included
- Height adjustable with a fully threaded body
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Does not include coil springs – sold separately
- These can only be run with aftermarket UCA’s for coilover clearance and full long travel lower arms – they will not work with OEM sized upper or lower arms
- Recommended Coils to run with these:
- C92-3016550 | Inner Diameter – 3.0″ | Length – 16″ | Spring Rate – 550lb/in
- C92-3016600 | Inner Diameter – 3.0″ | Length – 16″ | Spring Rate – 600lb/in
- C92-3016650 | Inner Diameter – 3.0″ | Length – 16″ | Spring Rate – 650lb/in
(9 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King Tacoma Shock Relocation Kit | 2005-2023 Tacoma
- Suits 2WD and 4WD 6-Lug 2005-2023 Toyota Tacoma models
- Shocks mounted in the factory location typically measure 2.5″ x 8″, the Dirt King relocation kit is designed to accommodate for 2.5″ x 12″ shocks – like These
- Includes left and right hand sides and all hardware (welding required)
- All metal is shipped raw, as it requires welding – you paint when it’s all done
- Rear shock mounts
- Shock tabs
- Shock tab gussets
- Low profile wrench
- Reservoir mounts
- Grade 8 mounting hardware
- Dirt King sticker pack
- Installation Instructions
- Suitable with Dobinsons 12″ Travel Smoothie MRA Shocks
(4 reviews) -
Skid Plates
Rear Shock Mount Skids | 2005-2023 Tacoma
- Includes one pair of shock mount skid plates (Driver/Passenger)
- Protects low hanging shock mounts on 2005-2023 Toyota Tacoma models
- Includes all hardware for installation
- Product includes a heavy duty black powder coat finish
- Made of 3/16″ Steel
- Fits OEM, Icon, Fox, King, Eibach, Bilstein and many others
- DOES NOT FIT ICON RXT REAR SHOCKS WITH SIDE-MOUNTED EYELET
- Made in Colorado, USA
(6 reviews) -
All Pro OffroadFREE SHIPPING
within 48 US StatesToyota Tacoma Overland Truck Bed Rack | 2005-2023
- Suits 2005 to 2023 Toyota Tacoma
- Rack hovers against the cab end of the bed and the sides
- Base price is bare steel
- Choose from 1/8” Thick Mild Steel (45 LBS) or 3/16” 5052 Aluminum (28 LBS)
- Choose from bare metal or powder coated
- Bed rack has mounting points for bungee cords/tie-down straps
- Designed to hold 4 8-gallon Action Packers
- Mounting points for Rotopax carriers
- Dimple died for extra strength
- CNC laser cut and formed
- Dimensions: 56.25” x 18.5”x3”
- Installation Instructions
- Photos show different versions of the same product type
- Made in the USA!!
(12 reviews)
