Your cart is currently empty!
ARB
Showing 31–60 of 72 resultsSorted by popularity
-
Differential | DrivetrainFREE SHIPPING
within 48 US StatesARB RD129 Rear Air Locker Toyota 8.4″ 30 Spline
- For Use only with Toyota 8.4″ 12 Bolt 30 spline Rear Axle
- Suits multiple vehicles, the full list is down below. Used in older Tacoma, Sequoia, Tundra and T100 Trucks.
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.Â
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
(16 reviews) -
Differential | DrivetrainFREE SHIPPING
within 48 US StatesARB RD146 Rear Tundra Air Locker 5.7L V8 10.5″
- For Use only with Toyota Tundra 5.7L V8 REAR 2007 to 2021 with 10.5″ 12 Bolt Ring Gear and 36 spline axles
- Will not suit 4.6L or 4.7L engines, as they use a smaller rear differential (RD152)
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.Â
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
(11 reviews) -
Skid PlatesFREE SHIPPING
within 48 US StatesARB 5421110 Under Vehicle Protection Kit | Toyota 4Runner 5th Gen (with KDSS)
- Suits all Toyota 4Runner 5th Gen models from 2010 to 2024 WITH KDSS
- You must check to make sure you have KDSS before ordering this kit
- 3mm pressed and folded sheet steel adds more strength than a standard folded sheet.
- Laser cut sheet steel.
- Zinc plated and powder coated with a silver textured finish.
- Recessed mounting bolts are protected and easy to remove for vehicle servicing.
- The Under Vehicle Protection will fit with or without an ARB front bumper. Fitment has not been confirmed with other aftermarket bumper designs
- Comprises 4 panels: Front Panel (Protects power steering, engine sump, sway bar), Diff Panel (Protects front diff mounts, engine sump), Transmission (Protects transmission and transmission controls) and Transfer Case (Protects transfer case)
- See more details below as well as product video
(9 reviews) -
Skid PlatesFREE SHIPPING
within 48 US StatesARB 5423010 Toyota Tacoma Skid Plate Set | 2005-2023 4×4
- Suits all Toyota Tacoma 4×4 models from 2005 to 2023 (2nd and 3rd Gen)
- 3mm pressed and folded sheet steel adds more strength than a standard folded sheet.
- Laser cut sheet steel.
- Zinc plated and powder coated with a silver textured finish.
- Recessed mounting bolts are protected and easy to remove for vehicle servicing.
- The Under Vehicle Protection will fit with or without an ARB front bumper. Fitment has not been confirmed with other aftermarket bumper designs
- Comprises 4 panels: Front Panel (Protects power steering, engine sump, sway bar), Diff Panel (Protects front diff mounts, engine sump), Transmission (Protects transmission and transmission controls) and Transfer Case (Protects transfer case)
- See more details below as well as product video
(11 reviews) -
-
ARB
ARB715LB Orange Snatch Strap Recovery 30′ x 4 1/3″ (33000 LB)
- A snatch strap is a Kinetic strap that stores energy to magnify the pulling power during a vehicle recovery
- Min. breaking strength: 15,000kg / 33,000 lb Specifically designed to stretch under load for maximum performance
- An ARB snatch strap is a very effective method of extracting a bogged or immobilized 4wd when a second vehicle is present
- Length: 9m / 30 feet. Width: 110mm / 4 1/3″Â
- Material: 100 percent nylon, Elasticity: Stretch (genuine) 20 percent. The kinetic energy generated by the elasticity aids with the recovery itself, while at the same time reducing the likelihood of vehicle damage.
- Reinforced Eyes. For vehicle recovery, a snatch strap is more suitable than a tow strap.
- All ARB snatch straps are woven and fabricated to ARB specifications, and tested by a NATA approved laboratory
- Part no. ARB715LB
- Min. breaking strength: 15,000kg / 33,000 lb
- Length: 9m / 30 feet
- Width: 110mm / 4 1/3″
- Elasticity: Stretch (genuine) 20%
- Material: 100% nylon
- Reinforced eyes: yes
- Eye & seam protector sleeves: yes
(12 reviews) -
ARB
ARB505 E-Z Deflator Kit 10-60 PSI Rapid Air Down Offroad Kit
- Corrosion resistant brass/stainless deflator tool
- Fully geared, solid brass precision movement
- Protective rubber gauge guard
- Easy to read dial with one PSI increments
- Includes updated canvas pouch for storage
- Original analog design, newer digital version is now also offered
(10 reviews) -
SnorkelFREE SHIPPING
within 48 US StatesSafari Tacoma Snorkel SS171HP – Tacoma 2nd Gen 2005-2015
- Suits Toyota Tacoma 2005-2015 Models – 2nd Gen Tacoma
- Raises air intake to prevent water ingestion, while also allowing vehicles to utilize clean air when driving in dusty conditions.
- Vehicle specific design and factory airbox adaption fitment.
- Manufactured using durable, UV stable cross linked polyethylene material.
- Supplied as a comprehensive kit, including the necessary fasteners and mounting brackets.
- Unique air ram design acts as a highly efficient water separator to remove rain water form incoming air stream.
- Designed and manufactured in Australia
- 10% higher CFM for this application over other brand snorkels, due to large body design
- Requires cutting and drilling of the fender and A-pillar. Full instructions and template provided.
(25 reviews) -
Leaf Springs - Tacoma 1st Gen
OMESB121 Tacoma Leaf Spring Bushing Kit | 1998-2004 Tacoma
- Suits 1998-2004 Toyota Tacoma 4×4 and Prerunner
- 1 kit fits both ends of ONE leaf spring (the fixed end and the shackle end top and bottom)
- Each kit comes with as pictured
- Order 2 kits to replace the bushings in 2 leaf springs
- Polyurethane bushings with steel sleeves
- Color:Â Yellow
- Material:Â Polyurethane
- Includes Shackle Bushing:Â Yes
- Includes Spring Pad Bushings:Â Yes
- Includes Sleeve:Â Yes
- Includes Hardware:Â No
- Estimated Install Time (Hours):Â 2
(9 reviews) -
Leaf Springs - Tacoma 1st Gen
OME EL122RB 2.25″ Leaf Spring for Toyota Tacoma 1998-2004
- Suits Toyota Tacoma 1st Gen 1998-2004 (will not fit the 1996 or 1997 models)
- Lifts 2.25″ over stock height
- This is the EL122RB – which is the sjhorter side and usually mounts onto the passenger side
- Draw-tapered and diamond cut leaves
- Bolted leaf clamps allow installation of anti-squeak nylon liners
- Fully scragged to reduce the risk of sagging
- Load tested to ensure the spring meets the required specification
- Military wrap design provides added safety
- Re-greasable nylon interleaf anti-friction pads reduce friction at the leaf tips
- Flat axle seat area allows a positive, safe axle mount and reduces spring stress
- Shot peened to reduce spring stress and increase spring life
- Two-stage leaf pack featured on most rear springs for optimum comfort
- Color: Black
- Weight: 26.2 kg
- Material: Steel
- Spring Rate: 120 / 283 lbf/in
- Eye Diameter: 40 mm (F) / 40 mm (R)
- Number Of Leaves: 5+2
- Primary Free Camber: 189Â mm
- Warranty: 3Â YR
- The other side leaf spring as well as Bushings and U-Bolts are sold separately
(11 reviews) -
Leaf Springs - Tacoma 1st Gen
OME EL122RA 2.25″ Leaf Spring for Toyota Tacoma 1998-2004
- Suits Toyota Tacoma 1st Gen 1998-2004 (will not fit the 1996 or 1997 models)
- Lifts 2.25″ over stock height
- This is the EL122RA – which is the taller side and usually mounts onto the driver’s side
- Draw-tapered and diamond cut leaves
- Bolted leaf clamps allow installation of anti-squeak nylon liners
- Fully scragged to reduce the risk of sagging
- Load tested to ensure the spring meets the required specification
- Military wrap design provides added safety
- Re-greasable nylon interleaf anti-friction pads reduce friction at the leaf tips
- Flat axle seat area allows a positive, safe axle mount and reduces spring stress
- Shot peened to reduce spring stress and increase spring life
- Two-stage leaf pack featured on most rear springs for optimum comfort
- Color: Black
- Weight: 26.2 kg
- Material: Steel
- Spring Rate: 120 / 283 lbf/in
- Eye Diameter: 40 mm (F) / 40 mm (R)
- Number Of Leaves: 5+2
- Primary Free Camber: 204 mm
- Warranty: 3Â YR
- The other side leaf spring as well as Bushings and U-Bolts are sold separately
(5 reviews) -
Suspension
OMESD23 Steering Damper | Land Cruiser 40 45 46 47 55 series
- Suits Toyota Landcruiser 40 45 46 47 and 55 series (all years and variants of these models)
- Nine Stage Coil Spring Valving For Optimum Performance
- A 15mm Piston Rod Provides Improved Strength
- Stone Guard Protects Piston Rod Against Stone Damage
- A 35mm Piston And Bore Allows Increased Oil Volume
- Twin Tube Design Protects Internal Components Against Stone Damage
- Multi-Lip Seal Prevents Oil Loss
- Original Stabilizer Mounts May Be Used Where Appropriate
- Photo for illustration purposes
(15 reviews) -
Suspension
OME Steering Damper – Toyota 4Runner Pickup (1985-1995)
- Suits 1985 to 1995 Toyota 4Runner with IFS torsion bar front end and 1985 to 2004 Toyota Hilux and Pickup with IFS torsion bar front end
- Nine Stage Coil Spring Valving For Optimum Performance
- A 15mm Piston Rod Provides Improved Strength
- Stone Guard Protects Piston Rod Against Stone Damage
- A 35mm Piston And Bore Allows Increased Oil Volume
- Twin Tube Design Protects Internal Components Against Stone Damage
- Multi-Lip Seal Prevents Oil Loss
- Original Stabilizer Mounts May Be Used Where Appropriate
- Photo for illustration purposes
(10 reviews) -
ARB
OME Jeep Steering Damper for XJ Cherokee TJ Wrangler ZJ Grand Cherokee
- Suits Jeep Wrangler TJ 1997-2006, Jeep Cherokee XJ 1984-2001 and Jeep Grand Cherokee ZJ 1993-1998
- A new steering damper helps fight bump steer and makes driving offroad feel smoother from the driver’s seat
- If you don’t know how old your current steering damper is, then it’s time to replace it
- Nine Stage Coil Spring Valving For Optimum Performance
- A 15mm Piston Rod Provides Improved Strength
- Stone Guard Protects Piston Rod Against Stone Damage
- A 35mm Piston And Bore Allows Increased Oil Volume
- Twin Tube Design Protects Internal Components Against Stone Damage
- Multi-Lip Seal Prevents Oil Loss
- Original Stabilizer Mounts May Be Used Where Appropriate
(7 reviews) -
ExcludedFREE SHIPPING
within 48 US StatesOME Upper Control Arms Pair – Tacoma Hilux Fortuner
- Suits Toyota Tacoma 4×4 2005-2023, Toyota Hilux 2005-2023, Toyota Fortuner 2005-2023
- Forged Ball Joint Housing
- Forged Eyelets
- Heavy Duty greasable Ball Joints
- OME Ball joint protective cap
- GIIRO bushings, free pivoting, grease free and maintenance free
- Increased camber and caster for 2in lift
- Mount provision for OE ABS wires
- ARB’s Intergrit powder coat finish
- Boxed in pairs with foam inserts
- Fitting instructions included
- OME Branded outer sleeve
- Tested and passed to meet VSB14 requirements
- 3 Year Manufacturers Warranty
- Made in Vietnam
(13 reviews) -
Control Arms - 200 SeriesFREE SHIPPING
within 48 US StatesOME Upper Control Arms Pair – 200 Series Land Cruiser
- Suits Land Cruiser 200 Series and Lexus LX570 2008-2021
- Forged Ball Joint Housing
- Forged Eyelets
- Heavy Duty greasable Ball Joints
- OME Ball joint protective cap
- GIIRO bushings, free pivoting, grease free and maintenance free
- Increased camber and caster for 2in lift
- Mount provision for OE ABS wires
- ARB’s Intergrit powder coat finish
- Boxed in pairs with foam inserts
- Fitting instructions included
- OME Branded outer sleeve
- Tested and passed to meet VSB14 requirements
- 3 Year Manufacturers Warranty
- Made in Vietnam
(13 reviews) -
Air Compressors
ARB CKMTA24 24V High Performance Twin Air Compressor
- Motors are water sealed, 100% ball bearing equipped (i.e. no bushings), and feature a unique linear brush pre-load system for extra long life, low heat and quiet operation throughout the life of the unit.
- Compact twin motor, dual cylinder design makes it the highest flowing compressor in its class (voltage vs. size). Highest air flow rate of any 24 Volt air compressor of its size on the market at 174LPM [6.16CFM].
- Full wiring loom included for simplified installation and easy plug-in connectivity to Air Locker control solenoids. (Note: Air Locker Manifold Kit #171503 required to mount solenoids).
- Motors are internally thermal protected against extreme temperature damage. Over-pressure safety valve equipped. Equipped with dual heavy duty Maxi-Fuses for professional in-line circuit protection and true circuit redundancy in case of a fault.
- Compressor pistons are equipped with a heavy duty European made cylindrical roller bearing. Hard-anodized cylinder bores and PTFE (Teflon) impregnated carbon fibre piston seals for reduced friction and maximum trouble free life.
- 24V, Draws 25.2 Amps, 6.16 CFM, 150 PSI max, 100% Duty Cycle
- 10.9 x 7.5 x 4.1 inches actual dimensions, 19.4 LBS with all items included
(7 reviews) -
ARB
OME 2851 Front Coil Springs | Land Cruiser 80 and 105 Series – Pair
- OME Part Number 2851
- Bar Size : 16 mm
- Free Height : 475/485 mm
- Number of Turns : 8.18
- Coil Weight (each): 5.3 Kg | 11.7 lbs
- Spring Rate : 220 lbs
- Sold in Pairs
(22 reviews) -
ARB
OME 2862 Rear Coil Springs | Land Cruiser 80 and 100 Series – Pair
- OME Part Number 2862
- Bar Size : 17 mm
- Free Height : 460/470 mm
- Number of Turns : 9.0
- Coil Weight (each): 7.8 Kg | 17.2 lbs
- Spring Rate : 170-260 lbs
- Variable Rate Springs
- Sold in Pairs
(21 reviews) -
ARB
OME 2860 Rear Coil Springs | Land Cruiser 80 and 100 Series – Pair
- OME Part Number 2860
- Bar Size : 17 mm
- Free Height : 480/490mm
- Number of Turns : 6.88
- Coil Weight (each): 6 Kg | 13.2 lbs
- Spring Rate : 220 lbs
- Sold in Pairs
(26 reviews) -
Differential | DrivetrainFREE SHIPPING
within 48 US StatesARB RD151 Front Tundra Air Locker 5.7L V8 8″
- For Use with Toyota Tundra 5.7L V8 front 2007 to 2021 with 8″ 34 spline axles
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.Â
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
(11 reviews) -
SnorkelFREE SHIPPING
within 48 US StatesSafari Snorkel for Toyota FJ Cruiser Snorkel 2010-2016
- Suits Toyota FJ Cruiser 2010-2016
- Safari V-Spec Snorkel
- Relocates Your Engine’s Air Intake Point to a Higher Location
- Crosslinked Polyethylene Construction
- Built to Perform in Extreme Weather Conditions
- Comes With Stainless Steel and Plated Hardware
- Bolt-On Installation; Drilling Is Required
- Supported by a 2-Year Warranty
- Fully Designed and Manufactured in Australia
- Designed and manufactured in Australia
- Requires cutting and drilling of the fender and A-pillar. Full instructions and template provided.
(20 reviews) -
Safari SnorkelFREE SHIPPING
within 48 US StatesSafari Snorkel SS1080HF for Jeep Gladiator and JL Wrangler
- Suits Jeep Wrangler JL and Gladiator JT with the 2.0L or 3.6L gas engines. Does not suit diesel or any other variant
- Relocates Air Intake Above Windshield
- Reinforces Performance in Extreme Conditions
- Crafted from Tough and Lightweight, UV Protected Polyethylene
- Connection Ducts Made of EPDM Molded Rubber
- With High-Flow Air Duct
- Uses High-Grade Stainless Steel Hardware
- CAD-Engineered for a Precise Fit
- Installation Requires Modifications
- Requires cutting and drilling of the exterior body parts (hood)
- Ties into Factory Air Box
- Carries a 3-Year Limited Warranty
- Made in Australia
(24 reviews) -
Fridge/FreezersFREE SHIPPING
within 48 US StatesARB Classic Series II 50 Qt. Fridge Freezer (Grey/Black) – 10801472
- Capacity: 50 Quart (72 x 12 oz cans)
- External Dimensions: 20in(H) x 15in(W) x 27.8in(D)
- Internal Dimensions: Fruit & Dairy Compartment: 8.1in (H) x 11.2in(W) x 6in(D).  Main Compartment: 15.5in(H) x 11.2in(W) x 13.3in(D)
- Weight: 53lbs
- Cooling Capacity: 50°F to 0°F
- Power: Built-in 12/24V DC and 100-240V AC power. Integrated battery protection system
- Current Draw: 0.87 amps/hour*. *Average power consumption tested at 37.4°F cabinet temperature, 78.8°F-87.8°F ambient temperature range, test duration of 66 hours and supply voltage of 12V DC
- Transmitting module: Bluetooth connectivity allows 2-way communication on SII fridges and 1-way display on SI fridges
- Warranty: Three year warranty from date of purchase
- Gun-metal grey with black highlights
- Removable lid with integrated seal
- Backlit, dimmable LED control panel with temperature display
- Bluetooth transmitter allows full-control and monitoring with free iOS and Android apps
- Receive an alert when someone leaves the lid open
- Rear-facing internal cabinet LED light with magnetic switch
- Durable, Secop compressor with smart electronic control system
- Tough powder coated steel outer casing
- Separate compartment for fruit and dairy products
- Durable detent hinge
- Integrated 3-stage battery protection system
- Rubber feet
- Strong, recessed steel carry handles
- Reversible basket with divider
- Convenient drain plug for simple cleaning
- Integrated evaporator
(7 reviews) -
Fridge/FreezersFREE SHIPPING
within 48 US StatesARB Fridge Freezer Classic Series II 37 Qt (Grey/Black) – 10801352
- Capacity: 37 Quart (50 x 12oz cans)
- External Dimensions: 16.9in(H) x 15in(W) x 27.8in(D)
- Internal Dimensions: Fruit & Dairy Compartment: 5in(H) x 11.2in(W) x 6in(D).  Main Compartment: 12.6in(H) x11.2in(W) x 13.3in(D)
- Weight: 45.6lbs
- Cooling Capacity: 50°F to 0°F
- Power: Built-in 12/24V DC and 100-240V AC power. Integrated battery protection system
- Current Draw: 0.85 amps/hour*. *Average power consumption tested at 37.4°F cabinet temperature, 78.8°F-87.8°F ambient temperature range, test duration of 66 hours and supply voltage of 12V DC
- Transmitting module: Bluetooth connectivity allows 2-way communication on SII fridges and 1-way display on SI fridges
- Warranty: Three year warranty from date of purchase
- Gun-metal grey with black highlights
- Removable lid with integrated seal
- Backlit, dimmable LED control panel with temperature display
- Bluetooth transmitter allows full-control and monitoring with free iOS and Android apps
- Receive an alert when someone leaves the lid open
- Rear-facing internal cabinet LED light with magnetic switch
- Durable, Secop compressor with smart electronic control system
- Tough powder coated steel outer casing
- Separate compartment for fruit and dairy products
- Durable detent hinge
- Integrated 3-stage battery protection system
- Rubber feet
- Strong, recessed steel carry handles
- Reversible basket with divider
- Convenient drain plug for simple cleaning
- Integrated evaporator
(6 reviews) -
60 62 Series Land Cruiser (1980-1989)
ARB 3410100 Toyota 60 Series Land Cruiser Front Winch Bumper
- Suits all Toyota Landcruiser 60 and 62 Series models from 1980 to 1989
- Enhances the look of the 60 Series or 62 Series as well as providing awesome protection against animal strikes or rear end accidents
- Full width single piece steel welded bumper, includes all mounting hardware
- Compatible with a range of low mount winches without an integrated solenoid pack
- Includes driving light mounts as well as CB antenna mounts, welded in place
- Durable black powder coat finish
- Includes recessed turn signals in the bumper that you can wire into your OEM harness for additional visibility
- Not as heavy as it looks, just over 100lbs out of the packaging
- Ships by truck freight – we will be in touch with you about shipping details
- Fitment of Warn XD9000 & M8000 winch requires special spacer kit – ARB part no. 3500050.
- Best suited to a 10k or 12k low-mount winch, due to overall truck weight and size
(2 reviews) -
Bronco (2021-2024+)FREE SHIPPING
within 48 US StatesARB 5480100 Skid Plate Kit | Ford Bronco 4-Door 2021+
- Ford Bronco Skid Plate Set, Suits Ford Bronco 2021+ 4-Door Models
- 3mm pressed and folded sheet steel adds more strength than a standard folded sheet.
- Laser cut sheet steel.
- Zinc plated and powder coated with a silver textured finish.
- Recessed mounting bolts are protected and easy to remove for vehicle servicing.
- The Under Vehicle Protection will fit with or without an ARB front bumper. Fitment has not been confirmed with other aftermarket bumper designs
- Comprises 4 panels: Front Panel (Protects power steering, engine sump, sway bar), Diff Panel (Protects front diff mounts, engine sump), Transmission (Protects transmission and transmission controls) and Transfer Case (Protects transfer case)
- See more details below as well as product video
(6 reviews) -
Bronco (2021-2024+)
Ford Bronco Diff Cover by ARB | 2021+
- Suits 2021+ Ford Bronco 2-door and 4-door models with Dana 44 Rear Axle
- High-tensile nodular iron structure protects differential and ring and pinion set from obstacles
- Computer-optimized, cross-brace design within the differential cover increases the structural rigidity of the axle acting as a truss
- Approach/departure angle optimized by angled exterior surface
- Prolonged carrier bearing life due to extra support to the bearing alignment
- Additional housing strength helps keep the ring and pinion gears meshing on the flat faces of the teeth, extending ring and pinion life and overall maximum load strength
- Magnet in the end of the dipstick allows the oil to be checked for tell-tale signs of internal damage without removing the cover or draining the oil
- Low profile drain plug design resists damage from obstacles
- Combination of the high-filler point and dipstick allows the oil to be checked for water contamination without having to drain the oil
- Unique dipstick/filler cap design allows differential oil level to be adjusted for customized high driveline angles
- Cover is powder coated, CNC machined, and clear-coated for a durable, professional, long-lasting finish; all hardware is hardened and plated
- Tensile-cap screws (supplied) are recessed for protection against obstacles which might damage or loosen the screws
- Made in Red or Black, choose below
(3 reviews) -
ARB
OME 2899 Rear Coil Springs | 4Runner FJ Cruiser GX470 GX460 – Pair
- OME Part Number 2899
- Bar Size : 19 mm
- Free Height : 400mm
- Number of Turns : 6.75
- Coil Weight (each): 6.9 Kg | 15.2 lbs
- Spring Rate : 387 lbs
- Sold in Pairs
(12 reviews) -
ARB
OME 2898 Rear Coil Springs | 4Runner FJ Cruiser GX470 GX460 – Pair
- OME Part Number 2898
- Bar Size : 18 mm
- Free Height : 400mm
- Number of Turns : 6.75
- Coil Weight (each): 6.1 Kg | 13.4 lbs
- Spring Rate : 318 lbs
- Sold in Pairs
(11 reviews)
