Dobinsons

Showing 751–780 of 947 results

Suspension
Ships FREE !!
within 48 US States
Dobinsons IMS45-60115 Rear IMS Shocks Pair
- Fully rebuildable and re-valvable
- SOLD IN PAIRS
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment – Suitable for most heavier vehicles
- Full 2 year limited warranty, no set rebuild time period
$650.00 Add to cart
Suspension
Ships FREE !!
within 48 US States
Dobinsons IMS45-60114 Front IMS Shocks Pair
- Fully rebuildable and re-valvable
- SOLD IN PAIRS
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment – Suitable for most heavier vehicles
- Full 2 year limited warranty, no set rebuild time period
$650.00 Add to cart
300 Series Land Cruiser (2021+)
Ships FREE !!
within 48 US States
Dobinsons IMS59-60440 IFP Front Struts Pair | Land Cruiser 300 Series
- Suits Toyota Land Cruiser 300 Series 2021+ (not sold in the USA)
- Adjusters on the shock body are black, not purple
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment – Suitable for most heavier vehicles
- Full 2 year limited warranty, no set rebuild time period
- SOLD IN PAIRS
$720.00 Add to cart
Dobinsons
Dobinsons GS43-788 Rear Shocks Pair | Isuzu Amigo Honda Passport 99-02
- Suits Isuzu Amigo and Honda Passport 2/1999 to 2002 models.
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls
- Japanese NOK Multi-Lip seals
- Fuchs German shock absorber oil
- Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- Matched to compliment Dobinsons Complete Suspension Systems
- Note: Photo is not of actual GS43-788 shock, used for reference of color only
- 484mm extended, 305mm compressed
$310.00 Add to cart
Tundra 2nd Gen (2007-2021)
Dobinsons L59-122-R Leaf Springs Pair for Toyota Tundra 07-21 (1000LBS+)
- L59-122-R – 5 + 2 Leaves (7 leaf pack) Raised Height (55mm, 2.25″ Lift) Heavy Duty for a constant load of at least 1000LBS (450KG)
- To make this leaf pack into the L59-121-R (1 step down) lighter pack, remove the #3 leaf
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Design features include Drawn, tapered and thinned leaf ends
- Manufactured to international quality standards ISO9001:2008 using premium grade Sup 9 silicon manganese spring steel,
- Anti-Friction inter leaf liners are use to reduce the friction at each leaf end where the load is creates and provides a smoother, quieter ride.
- Sold as a pair
- Note: Greasable bush kits (PB59-1102K), greasable pins (SP59-060), and u-bolts (UB59-437K) are available separately. These do not come with bushings
- These are intended for people with a slide in camper, custom bed and canopy or a combination of 1000LBS of constant rear weight in addition to the stock bed weight, and to maintain 2-2.25″ of lift over stock
- Photo for illustration purposes
$1,100.00 Add to cart
Suspension
Ships FREE !!
within 48 US States
Dobinsons 3-Way Adjustable MRA Rear Shocks Pair | Jeep Gladiator JT (2-4″ lift)
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Piggyback Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Sold in Pairs
- 732mm extended, 451mm compressed
$1,350.00 Add to cart
200 Series Land Cruiser (2008-2021)
Dobinsons Tubular UCA Kit | 200 Series and LX570 – No Ball Joints
- Includes left and right hand side arms, OE style rubber frame bushings installed, and washers
- This does not include any ball joints. Use OEM or aftermarket OE size upper ball joints
- Has 3 degrees of caster built in, no adjustability or settings required
- Made from HSLA (High Strength Low Alloy) Steel
- 5mm (0.2″) wall thickness
- Powder coated black
- Works for any lift height of 1.5″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Product Video
- Also available with ball joints installed, here
$575.00 Add to cart
Montero NM NP NS NT 2000+
Ships FREE !!
within 48 US States
Dobinsons MRA Lift Kit for Mitsubishi Montero NM NP NS NT 2000+ Wagons
- All selections are for the 2000+ US Spec V6 Gasoline 5-door Wagon models
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Shock Design
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Includes 2 Front Struts, 2 Rear Shocks, and 4 Coil Springs
- Note: Coil seat should be set at 244mm from the center of the lower bushing to the notch in the coil seat, same as original coil seat height. The coils do the lifting. Fine tuning up or down can be done to tune the height or level the vehicle left to right, if required
- Full 2 year limited warranty, no set rebuild time period
From $3,105.00 Select options
Montero NM NP NS NT 2000+
Dobinsons C43-125 Rear 1.75″ Lift Coil Springs for Montero 2000-06
- 1.75-2.0″ rear lift with 110-220LBS constant weight on a Mitsubishi Montero 2000-06 USA model
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
$405.00 Add to cart
Montero NM NP NS NT 2000+
Dobinsons C43-126 Front 1.75″ Lift Coil Springs for Montero 2000-06 (Heavy Load)
- 1.75-2.0″ lift with 110-220LBS constant weight on a Mitsubishi Montero 2000-06 USA model
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
$270.00 Add to cart
Montero NM NP NS NT 2000+
Dobinsons C43-124 Front 1.75″ Lift Coil Springs for Montero 2000-06
- 1.75″ lift with stock weight on a Mitsubishi Montero 2000-06 USA model
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
$270.00 Add to cart
Montero NM NP NS NT 2000+
Ships FREE !!
within 48 US States
Dobinsons MRA 3-Way Adjustable Rear Shocks Pair | Mitsubishi Montero 2000+
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Universal Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
$1,150.00 Add to cart
Montero NM NP NS NT 2000+
Ships FREE !!
within 48 US States
Dobinsons MRA 3-Way Adjustable Front Struts Pair | Mitsubishi Montero 2000+
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Universal Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Does not include coil springs or top mounts – sold separately
- Instructions on setting coil seat height
- Photos for illustration purposes
$1,280.00 Add to cart
Dobinsons
Ships FREE !!
within 48 US States
Dobinsons MRA59-A710 3-Way Adjustable Front Struts Pair | Sequoia 2008-2022
- Pair of Struts only, no coils included and not preassembled
- If you’re looking for an assembled set of coilovers, those are here: Assembled Coilovers for 2008-2022 Sequoia
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Requires lower mount clearancing to fit the larger lower leg of the new coilover (see attached photo)
- See attached photo for correct hose routing, can vary depending on UCA’s used
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- SOLD IN PAIRS
- Full 2 year limited warranty, no set rebuild time period
- Does not include coil springs – sold separately
- Front coilover assembly instructions
- New UCA’s are required for proper coilover and hose clearance, see all options
- Aftermarket wheels with +18 Offset or less REQUIRED to avoid reservoir + hose rubbing at full lock
- Link to recommended 16″ coils with a 3″ inner diameter and 650LB Spring Rate
- Link to add assembly labor charge, so that when you buy these struts and the coils, you can have them preassembled before shipping
$1,790.00 Add to cart
Shocks + Struts - Sequoia 3rd Gen
Ships FREE !!
within 48 US States
Dobinsons 3.0-4.0″ Pre-Assembled MRA Coilovers for Toyota Sequoia 2023+
- Suits Toyota Sequoia 2023-2024+ Models
- TRD Pro Models yield 1″ less lift than listed here, as they are already lifted taller than base models
- Sold as a Pair, ready to bolt in
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment
- Looking for a quick and easy way to lift your Sequoia? This is your answer
- Select your desired lift height and tell us your weight – we’ll take care of the rest!!
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- SOLD IN PAIRS
- Full 2 year limited warranty, no set rebuild time period
- Must mount the banjo fitting and hose inwards on MRA struts
- Coil seat for MRA59-A446 will be set at 175mm (6.87″) from the strut bushing eye
- Photos for illustration purposes
- Instructions for setting and adjusting coil seat height
- Note about lift heights – all vehicles can have some variance and desired lift height may need to be adjusted to suit your specific vehicle. Adding 2.5″ or more lift, new UCA’s should be added for proper articulation and correct wheel alignment
- If doing a 4″ lift in the front, a diff-drop kit or longer TRD CV-axles are REQUIRED, failure to complete these requirements could cause OE CV-axle failure
- TRD axle shafts: PT362-3432B and PT362-3431B
- Front Installation Instructions
- Link to Matching rear shocks
$1,960.00 Select options
Shocks + Struts - Sequoia 3rd Gen
Dobinsons 3.0-4.0″ Pre-Assembled IMS Coilovers for Toyota Sequoia 2023+
- Suits Toyota Sequoia 2023-2024+ Models
- TRD Pro Models yield 1″ less lift than listed here, as they are already lifted taller than base models
- 66mm/2.6” Bodied Series – 60mm hi-flow CNC 6061 Billet alloy piston – 60mm bore – Vehicle specific fitment
- Looking for a quick and easy way to lift your Sequoia? This is your answer
- Select your desired lift height and tell us your weight – we’ll take care of the rest!!
- Dobinsons IMS are height adjustable by a threaded body with adjustable collar
- The Dobinsons IMS Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes – Sequoia IMS coilovers use a slightly different top mount
- Instructions for setting and adjusting coil seat height
- Note about lift heights – all vehicles can have some variance and desired lift height may need to be adjusted to suit your specific vehicle. Adding 2.5″ or more lift, new UCA’s should be added for proper articulation and correct wheel alignment
- If doing a 4″ lift in the front, a diff-drop kit or longer TRD CV-axles are REQUIRED, failure to complete these requirements could cause OE CV-axle failure
- TRD axle shafts: PT362-3432B and PT362-3431B
- Link to Matching rear shocks
$1,270.00 Select options
Full Suspension Kits - Xterra
Ships FREE !!
within 48 US States
Dobinsons 1.5″ Lift MRA Coilovers – Nissan Xterra 05+
- Remote Resi Coilovers Suit Nissan Xterra 4×4 Models (2005-2015) – lifts 1.5″
- Looking for a quick and easy way to lift your Xterra? This is your answer
- Dobinsons MRA are height adjustable by a fully threaded body
- The Dobinsons MRA Coilovers will come pre-assembled with new struts, coils and top mounts
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Reservoir Bracket and Hardware, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Length specs – 395mm extended, 266mm compressed
- Photos for illustration purposes
- FITTING INSTRUCTIONS
- Instructions for setting coil seat height
- Link to the matching rear shocks
From $1,795.00 Select options
Full Suspension Kits - Frontier D41
Ships FREE !!
within 48 US States
Dobinsons MRA Extended Travel Coilovers for Nissan Frontier D41 2022+
- Extended Travel Coilovers Suit Nissan Frontier D41 4×4 Models 2022-2023+ – lifts 2-3″ depending on selections made below
- These extended travel struts REQUIRE aftermarket UCA’s for full travel, like Dobinsons
- Looking for a quick and easy way to lift your Frontier? This is your answer
- Dobinsons MRA are height adjustable by a fully threaded body
- The Dobinsons MRA Coilovers will come pre-assembled with new struts, coils and top mounts
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Reservoir Bracket and Hardware, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Length specs – 278mm compressed and 410mm extended
- Photos for illustration purposes
- FITTING INSTRUCTIONS
- Instructions for setting coil seat height
- Link to the matching rear shocks
From $1,795.00 Select options
Jimny 2018+
Ships FREE !!
within 48 US States
Dobinsons Suzuki Jimny IMS Suspension Kit | 2018+
- Suits 2018-2023 Suzuki Jimny GJ – 40mm lift front and rear
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Fully rebuildable and re-valvable shocks
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base Kit Includes 2 Front IMS Monotube Shocks, 2 Rear IMS Monotube Shocks, and 4 Coil Springs – Select your preferences
From $2,070.00 Select options
Jimny 2018+
Dobinsons Front Jimny Crossmember Drop Kit | Jimny 2018+
- Suits Suzuki Jimny 1998-2017 and 2018+
- Zinc plated for a long lasting finish
- Solid steel construction, includes all necessary longer bolts for simple installation
- See attached photo to show how it looks when installed
- Dobinsons transmission and transfer case cross member spacer kit
- Designed to correct the angle of the front driveshaft after lifting the vehicle
- Lifting the vehicle can cause driveline vibration issues, so reduce those, this kit is recommended.
$60.00 Add to cart
Dobinsons
Dobinsons ±2 ½ – 3° Caster Bushing Kit for Suzuki Jimny
- Suits Suzuki Jimny 1998-2017 and 2018+
- High quality rubber, producing the highest ride quality
- Adjustable during installation to offer ±2 ½ – 3° of caster adjustment
- Replaces OE bushes holding front and radius arms to the axle
- Order 2 for 1 vehicle to change it all
- Raising Vehicle Will Effect Wheel Alignment. It is Recommended that this Castor Adjustment Kit to be Fitted and a Wheel Alignment Carried Out.
- Installation Instructions
$185.00 Add to cart
Jimny 2018+
Dobinsons C57-143 Rear Coils | Jimny 2018+ 40mm Lift
- Suits Suzuki Jimny 2018+ 40mm Lift with stock rear end weight up to 60KG added
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
$240.00 Add to cart
Jimny 2018+
Dobinsons C57-071 Rear Coils | Jimny 2018+ 40mm Lift HD
- Suits Suzuki Jimny 2018+ 40mm Lift with 100-200KG of added rear end weight (bumper, rooftop tent, etc)
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
$270.00 Add to cart
Jimny 2018+
Dobinsons C57-110 Front Coils | Jimny 2018+ 40mm Lift HD
- Suits Suzuki Jimny 2018+ 40mm Lift with 40-70KG of added front end weight (bumper, winch, etc)
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
$240.00 Add to cart
Jimny 2018+
Dobinsons C57-142 Front Coils | Jimny 2018+ 40mm Lift
- Suits Suzuki Jimny 2018+ 40mm Lift with stock weight
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
$240.00 Add to cart
Dobinsons
Ships FREE !!
within 48 US States
Dobinsons IMS57-50618 IMS Shocks Pair | Suzuki Jimny Rear Shocks
- Suits Suzuki Jimny 1998-2017 and 2018+
- SOLD IN PAIRS
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
$580.00 Add to cart
Dobinsons
Ships FREE !!
within 48 US States
Dobinsons IMS57-50617 IMS Shocks Pair | Suzuki Jimny Front Shocks
- Suits Suzuki Jimny 1998-2017 and 2018+
- SOLD IN PAIRS
- Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
$580.00 Add to cart
Full Suspension Kits - Bronco 2021+
Ships FREE !!
within 48 US States
Dobinsons IMS Ford Bronco Suspension Kit 4 DOOR
- Suits 4 DOOR Ford Bronco 2021-2023 Models (will not fit Bronco Sport)
- Complete suspension kit with multiple coil spring options to suit the vehicle as well as the added weight
- (The 2 Door Bronco Kit is on a different page)
- Note: Photo is not of actual IMS struts. Ford Bronco IMS have a crossbar style lower front shock bush
- Front Springs Provide Approximately 3″-4″ Lift Above Non Sasquatch Models & 2″-3″ Lift Above Sasquatch Models.
- Rear Springs Provide Approximately 3″ Lift Above Non Sasquatch Models & 2″ Lift Above Sasquatch Models.
- Dobinsons IMS shocks and struts are fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Standard coil seat height should be set to 243mm (9.55″) front and rear. See instructions on setting coil seat height on left
- Reuse OE strut top mounts
- Select the coil springs that match the Bronco version you have as well as the added weight you have put on it, if any
From $1,300.00 Select options
Full Suspension Kits - Bronco 2021+
Ships FREE !!
within 48 US States
Dobinsons IMS Ford Bronco Suspension Kit 2 DOOR
- Suits 2 DOOR Ford Bronco 2021-2023 Models (will not fit Bronco Sport)
- Complete suspension kit with multiple coil spring options to suit the vehicle as well as the added weight
- (The 4 Door Suspension Kit is on a different page)
- Note: Photo is not of actual IMS struts. Ford Bronco IMS have a crossbar style lower front shock bush
- Front Springs Provide Approximately 3″-4″ Lift Above Non Sasquatch Models & 2″-3″ Lift Above Sasquatch Models.
- Rear Springs Provide Approximately 3″ Lift Above Non Sasquatch Models & 2″ Lift Above Sasquatch Models.
- Dobinsons IMS shocks and struts are fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Standard coil seat height should be set to 243mm (9.55″) front and rear. See instructions on setting coil seat height on left
- Reuse OE strut top mounts
- Select the coil springs that match the Bronco version you have as well as the added weight you have put on it, if any
From $1,300.00 Select options
Bronco 2021-2024+
Dobinsons Ford Bronco Rear Coils | C19-567V
- Dobinsons C19-567V Variable Rate Springs Suits Ford Bronco:
  
  2 Door – Base, Big Bend, Black Diamond, Outer Banks – 330-550Lb Load
  
  2 Door – BL, Wildtrack, First Edition – 330-550Lb Load
  
  4 Door – Base, Big Bend, Black Diamond, Outer Banks – 330-550Lb Load
- Coil Springs Can Only Be Fitted To Dobinsons IMS19-50099
- Coils Provide Approximately 3″-4″ Lift Above Non Sasquatch Models & 2″-3″ Lift Above Sasquatch Models
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish – Choose what color you would like
- Made in Australia
- Sold in Pairs
$270.00 Select options