Archives

on
  • Suits 4th and 5th Gen 4Runner 2003-2024, FJ Cruiser (all years), GX470, GX460 (without KDSS)
  • Order 1 for 1 vehicle
  • Adjustable (on vehicle) from 165mm – 206mm – Suits standard and long travel rear lifts
  • Custom Forged Oversized (22mm ball) Chromoly Rod End / Joints
  • Premium Silicone Dust Boots
  • High Carbon Steel Center Link
  • Black EDP Coating for corrosion resistance
  • High Quality Polyurethane Bushings on frame side
  • Serrated Oval / Distorted Thread Locking Nut – The factory sway bar material expands and contracts as you drive, thus causing the nut to come loose and the sway bar link to disconnect. This is not ideal. This style nut, is the best solution we have found to the issue, though we do still recommend the use of thread locker at install
  • Mounting hardware included
  • Rod end machined to accept hex key to prevent the rod end from spinning during installation. Other brands come with a nut on the inner side of the shaft, which is harder to use and more likely to cause you to tear the boot upon installation
  • Sold as a pair
  • Maintenance Free Design
  • 2 year unlimited mile warranty

on
  • D.O.T. Certified stainless steel braided and coated with a PVC cover
  • 20″ long, works with long travel rear suspension setups
  • Suits up to 4″ of lift with long travel shocks or not
  • Suits the following vehicles: Toyota 4Runner 4th Gen 2003-2009, Toyota 4Runner 5th Gen 2010-2024, Toyota FJ Cruiser all years, Lexus GX470 all years, Lexus GX460 all years
  • Not recommended for stock or un-lifted vehicles, as the brake lines are much longer than necessary
  • Sold as a pair with new retaining clips
  • Warranty- 2 Year unlimited mile warranty against manufacturers defects.

on
  • Individual Air Accessory Components Are Also Available, Including Compressors, Air Tanks, And Mounting Solutions, Providing A Wide Variety Of Air Control Assist Solutions
  • Adjust The Ride For Various Load And Road Conditions With A Switch, Remote Or Mobile App
  • Provides An Instant Air Source For The Air Helper Springs Or Accessories
  • Single Point Fill (Both Air Springs Fill To The Same Pressure)
  • Light Duty Compressor Specs (100 Pounds Per Square Inch Max Air Pressure, 9 Percent Duty Cycle, 0.32 CFM)
  • Electric analog gauge and a single toggle switch (includes housing for easy installation).
  • Plug and play wiring harness.
  • 30ft of 1/4″ tubing. All required hardware for installation.
  • No-Drill Mounting Plate
  • Limited 2 Year Warranty
  • Dash Panel Style: Controls Two Air Springs Simultaneously
  • Type: Heavy Duty
  • Maximum Pressure (PSI): 100 Pounds Per Square Inch
  • Operation Type: Switch Operated
  • Estimated Install Time (Hours): 2
  • Installation Manual

on
  • Complete hydro bump stop kit to replace the factory coil isolator and internal bump stop
  • Suits the Rear of Toyota Tundra 2022-2025+ and Toyota Tacoma 2024-2025+ with coil spring rear end
  • CNC Machined 50mm Billet Aluminum Piston
  • EDP Coated 3mm Thick 56mm Steel Body
  • Threaded Body For Height Adjustment to adjust when the stop will engage
  • Supplied with both Interchangeable Super Quiet Rubber Rod End & Hard Nylon
  • 30mm Micro Polished Hard Chrome Shaft
  • Slow Rebound Valving To Prevent Bucking
  • Removable Dust Cover Boot For Stealth Appearance
  • Fully Rebuildable & Tunable
  • O-Ring Travel Indicator
  • Heavy Duty Extreme-Race style Triple Seal Design
  • Nitrogen Gas Charged & Tunable (100 to 300 PSI)
  • Pre-charged to 110 PSI
  • Extra Short Dead Lengths For Compact Fitment
  • Includes full fit kit, 2 hydro bump stops, and spacer blocks for frame-mounted external bump stops
  • Kit Includes:
    • HBS59-027FK Mounting Kit
    • HBS56-009 Hydraulic Bump Stops
  • 46mm – 1.8″ stroke, 105mm – 4″ thread length, 188mm – 7.4″ extended length, 142mm – 5.6″ compressed length