Your cart is currently empty!
FJ Cruiser
Showing 121–150 of 159 results
-
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD121 Front Air Locker Toyota Lexus 8″ IFS 30 Spline 3.73-
- For Use With Toyota 8″ IFS Clamshell differential with 30 Spline Axles and 3.73 And Down Factory Gears
- Usually all models that came with a manual transmission used 3.73- factory gear ratios, but you must check before ordering
- Factory R&P may use either RD111 or RD121 depending on ratio. All known aftermarket R&P sets suit RD121.
- If you are re-gearing, check with the gear manufacturer for which Air Locker to order
- Full vehicle fitment list is further down in the main description, includes 4Runner, Tacoma, FJ Cruiser, GX470, GX460
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Select options -
SuspensionDobinsons 1.5″ to 3.5″ Lift Kit Toyota FJ Cruiser 2010 to 2017 (all options)
- For Late Model FJ Cruisers from 2010-2017
- Choose from Twin Tube, IMS Monotube, or 3-Way Adjustable MRA Struts and Shocks from the options below
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base Kit Includes 2 Front Struts, 2 Rear Shocks, and 4 Coil Springs
From $1,200.00 Select options -
Sale!SaleShips FREE !!
within 48 US StatesIcon Tubular Upper Trailing Arm Kit | 4Runner FJ Cruiser GX470 GX460
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460
- CNC machined & notched 1026 DOM steel construction
- Multi durometer bushing for noise free operation and maximum angularity
- No grease required for life of bushings
- Quality JM12T PTFE-lined FK Rod Ends
- Adjustable for various lift heights & driveline angles
- ICON1K tested in extreme off-road conditions
- Fabricated components covered under ICON’s lifetime warranty
- Sold as a Pair
- Installation Guide
- Warranty Info
Original price was: $482.95.$459.95Current price is: $459.95. Add to cart -
Sale!SaleShips FREE !!
within 48 US StatesIcon Billet Upper Trailing Arm Kit | 4Runner FJ Cruiser GX470 GX460
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460
- CNC machined, billet aluminum construction
- Chemical etched, clear anodized finish for corrosion resistance
- On-vehicle adjustability using ICON’s pinch housing and double adjuster
- 3/4″ Rod End and Polyurethane Pivots, for excellent strength and longevity
- High Misalignment Spacers for Excellent Articulation
- Sold as a Pair
- Installation Guide
- Warranty Info
Original price was: $609.95.$579.95Current price is: $579.95. Add to cart -
Sale!SaleShips FREE !!
within 48 US StatesIcon Billet Lower Trailing Arm Kit | 4Runner FJ Cruiser GX470 GX460 LC200
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460, Lexus LX570 and 200 Series 2008-2021
- On vehicle length adjustment for different ride heights and pinion angles using ICON’s Double Adjuster System
- Vehicle specific, high clearance design for reduced link contact with obstacles
- Replaceable Nylon ROCK Slider to protect the link from damage
- CNC machined 6061 aluminum construction
- Large FK Bearing JMX16T PTFE-lined rod ends
- Greaseable, multi-piece polyurethane bushings for maximum angularity and noise isolation
- Covered by ICON’s Limited Lifetime Warranty
- Sold as a Pair
- Installation Guide
- Warranty Info
Original price was: $976.45.$929.95Current price is: $929.95. Add to cart -
Sale!SaleShips FREE !!
within 48 US StatesIcon Tubular Lower Trailing Arm Kit | 4Runner FJ Cruiser GX470 GX460 LC200
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460, Lexus LX570 and 200 Series 2008-2021
- CNC machined & notched 1026 DOM steel construction
- Multi durometer bushing for noise free operation and maximum angularity
- No grease required for life of bushings
- Quality JM16T PTFE-lined FK Rod Ends
- Adjustable for various lift heights & driveline angles
- Offset lower link front pivots improve roll steer
- Tangent lower link barrel design reduces risk of off-road hangups
- Integrated OEM emergency brake bracket mount
- ICON1K tested in extreme off-road conditions
- Fabricated components covered under ICON’s lifetime warranty
- Sold as a Pair
- Installation Guide
- Warranty Info
Original price was: $577.45.$549.95Current price is: $549.95. Add to cart -
Bump StopsShips FREE !!
within 48 US StatesDobinsons 2.2″ Hydraulic Bump Stop IFS Weld on Mount Kit
- Kit includes front Weld on Mounts (Pair) and Dobinsons HBS56-009 Pair of Hydro Bump Stops
- Made for IFS (independent front suspension) vehicles to replace the OEM rubber bump stop
- HBS56-009 – 56mm (2.2″) body | 46mm (1.8″) stroke | 188mm (7.4″) extended | 142mm (5.6″) compressed | 105mm (4.0″) thread length
- CNC Machined 50mm Billet Aluminum Piston
- EDP Coated 3mm Thick 56mm Steel Body
- Threaded Body For Height Adjustment
- Supplied with both Interchangeable Super Quiet Rubber Rod End & Hard Nylon
- 30mm Micro Polished Hard Chrome Shaft
- Slow Rebound Valving To Prevent Bucking
- Removable Dust Cover Boot For Stealth Appearance
- Fully Rebuildable & Tunable
- O-Ring Travel Indicator
- Heavy Duty Extreme-Race style Triple Seal Design
- Nitrogen Gas Charged & Tunable (100 to 300 PSI)
- Pre-charged to 150 PSI
- Extra Short Dead Lengths For Compact Fitment
- Universal design threaded weld on bump stop can to hold the 2.2″ body bump stop
- Cans have 3mm walls for increased strength
- Kit is ideal for those who bottom out often in their offroad driving or go really hard at high speeds
- Could suit a wide range of vehicles as listed below, but remember they are universal and will require adaptation to your vehicle and welding
- Custom fitting and welding is required
- Photo attached shows these bump stops installed with the weld-on mounts on a 3rd Gen Tacoma
From $1,090.00 Select options -
Bump Stops
Dobinsons 2.2″ Hydraulic Bump Stop IFS Weld on Mounts
- Universal design threaded weld on bump stop can to hold a 2.2″ body bump stop
- Intended to be used with the Dobinsons HBS59-009 Hydro bumps
- 3mm walls for increased strength
- Sold as a pair
- Ideal for those who bottom out often in their offroad driving or go really hard at high speeds
- Could suit a wide range of vehicles as listed below, but remember they are universal and will require adaptation to your vehicle and welding
- Custom fitting and welding is required
$400.00 Add to cart -
Excluded
OME Upper Control Arms – 2003+ 4Runner FJ GX470 GX460
- Suits Toyota 4Runner (2003-2024), FJ Cruiser, Lexus GX470 and GX460
- Forged Ball Joint Housing
- Forged Eyelets
- Heavy Duty greasable Ball Joints
- OME Ball joint protective cap
- GIIRO bushings, free pivoting, grease free and maintenance free
- Increased camber and caster for 2in lift
- Mount provision for OE ABS wires
- ARB’s Intergrit powder coat finish
- Boxed in pairs with foam inserts
- Fitting instructions included
- OME Branded outer sleeve
- Tested and passed to meet VSB14 requirements
- 3 Year Manufacturers Warranty
- Made in Vietnam
$606.00 Add to cart -
Sale!Wheels
Warn 104484 6 Lug Epic Wheel Hubs Center Cap – Grey
- Suits Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- Grey Finish
- Expertly Made From Premium Materials
- Meets The Highest Quality Standards
- ISO 9001: 2015, ISO 14001: 2015 CERTIFIED
- Easy To Install
- Limited 90 Day Supplier Warranty
- Wheel Series Compatibility: Moonsault/ Diamond Cutter And Jack Hammer Series Wheels
- Bolt Pattern (MM): 6×139.7
- Installation Type: Bolt-On
- Style: Closed
- Color: Grey
- Quantity: Single
- Bolt Pattern (IN): 6×5.50
- Material: Plastic
- Estimated Install Time (Hours): 0.25
Original price was: $27.29.$24.00Current price is: $24.00. Add to cart -
Sale!Wheels
Warn 104483 6 Lug Epic Wheel Hubs Center Cap – Black
- Suits Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- Black Finish
- Expertly Made From Premium Materials
- Meets The Highest Quality Standards
- ISO 9001: 2015, ISO 14001: 2015 CERTIFIED
- Easy To Install
- Limited 90 Day Supplier Warranty
- Wheel Series Compatibility: Moonsault/ Diamond Cutter And Jack Hammer Series Wheels
- Bolt Pattern (MM): 6×139.7
- Installation Type: Bolt-On
- Style: Closed
- Color: Black
- Quantity: Single
- Bolt Pattern (IN): 6×5.50
- Material: Plastic
- Estimated Install Time (Hours): 0.25
Original price was: $27.29.$24.00Current price is: $24.00. Add to cart -
Sale!WheelsShips FREE !!
within 48 US StatesWarn 104487 Diamond Cutter Wheel – 17×8.5″ 6×5.5″ 0 Offset – Black
- Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 6 lugs, Uses OEM lug nuts
- Sold Individually
- Black Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: Not Applicable
- Weight: 30 LBS
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Black
- Bolt Pattern Inch: 6×5.50
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 6×139.7
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 106.10
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: 6 Spoke
- With Inserts: No
- Load Capacity: 2500
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: Yes
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Sale!WheelsShips FREE !!
within 48 US StatesWarn 104490 Jack Hammer Wheel – 17×8.5″ 6×5.5″ 0 Offset – Gun Metal
- Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 6 lugs, Uses OEM lug nuts
- Sold Individually
- Gun Metal Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: Not Applicable
- Weight: 30 LBS
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Gun Metal
- Bolt Pattern Inch: 6×5.50
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 6×139.7
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 106.10
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: Solid Center
- With Inserts: No
- Load Capacity: 2500
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: Yes
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Sale!WheelsShips FREE !!
within 48 US StatesWarn 104489 Jack Hammer Wheel – 17×8.5″ 6×5.5″ 0 Offset – Black
- Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 6 lugs, Uses OEM lug nuts
- Sold Individually
- Black Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: Not Applicable
- Weight: 30 LBS
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Black
- Bolt Pattern Inch: 6×5.50
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 6×139.7
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 106.10
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: Solid Center
- With Inserts: No
- Load Capacity: 2500
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: Yes
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Sale!WheelsShips FREE !!
within 48 US StatesWarn 104485 Moonsault Wheel – 17×8.5″ 6×5.5″ 0 Offset – Black
- Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 6 lugs, Uses OEM lug nuts
- Sold Individually
- Black Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: Not Applicable
- Weight: 30 LBS
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Black
- Bolt Pattern Inch: 6×5.50
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 6×139.7
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 106.10
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: 8 Spoke
- With Inserts: No
- Load Capacity: 2500
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: Yes
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Sale!WheelsShips FREE !!
within 48 US StatesWarn 104486 Moonsault Wheel – 17×8.5″ 6×5.5″ 0 Offset – Gun Metal
- Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 6 lugs, Uses OEM lug nuts
- Sold Individually
- Gun Metal Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: Not Applicable
- Weight: 30 LBS
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Gun Metal
- Bolt Pattern Inch: 6×5.50
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 6×139.7
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 106.10
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: 8 Spoke
- With Inserts: No
- Load Capacity: 2500
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: Yes
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Performance Upgrades - FJ Cruiser EarlyShips FREE !!
within 48 US StatesPowerbrake D-Line HP Rotor and Pad Kit | FJ Cruiser 10-16 Rear
- Suits Toyota FJ Cruiser 2010-2014 Rear
- Also available for the FRONT
- Powerbrake D-Line Features
- Rotors are cast from a proprietary high carbon cast-iron alloy.
- Rotors are machined to tolerances up to three times tighter than the industry norm.
- All Powerbrake rotors feature our MTR (Max Temperature Recording) system.
- Proprietary black disc surface coating ensures quicker bed-in and max brake performance.
- Spiral slots on the rotor fiction surface clear friction gasses, debris and water.
- Matched high friction PB05 brake pads take the guesswork out of pad selection.
- Pad compound PB05 is manufactured in Japan and has been specifically formulated for use on 4×4 vehicles
- Powerbrake D-Line Benefits at a Glance
- Reduced stopping distances in both wet and dry conditions.
- Reduced brake fade and improved brake consistency.
- Improved initial brake response (bite).
- Improved brake modulation particularly during emergency stops.
- Improved resistance to rotor distortion (warping) and cracking at high temperatures.
- What’s Included in Powerbrake D-Line?
- 2 x Standard OEM diameter high performance slotted rotors for your 4WD or truck – Made in South Africa.
- An axle set of matched PB05 high-performance brake pads – Made in Japan.
- Fits as per a standard rotor and pad change, using the vehicle’s original calipers.
$840.00 Add to cart -
Performance Upgrades - FJ Cruiser EarlyShips FREE !!
within 48 US StatesPowerbrake D-Line HP Rotor and Pad Kit | FJ Cruiser 06-09 Rear
- Suits Toyota FJ Cruiser 2006-2009 Rear
- Also available for the FRONT
- Powerbrake D-Line Features
- Rotors are cast from a proprietary high carbon cast-iron alloy.
- Rotors are machined to tolerances up to three times tighter than the industry norm.
- All Powerbrake rotors feature our MTR (Max Temperature Recording) system.
- Proprietary black disc surface coating ensures quicker bed-in and max brake performance.
- Spiral slots on the rotor fiction surface clear friction gasses, debris and water.
- Matched high friction PB05 brake pads take the guesswork out of pad selection.
- Pad compound PB05 is manufactured in Japan and has been specifically formulated for use on 4×4 vehicles
- Powerbrake D-Line Benefits at a Glance
- Reduced stopping distances in both wet and dry conditions.
- Reduced brake fade and improved brake consistency.
- Improved initial brake response (bite).
- Improved brake modulation particularly during emergency stops.
- Improved resistance to rotor distortion (warping) and cracking at high temperatures.
- What’s Included in Powerbrake D-Line?
- 2 x Standard OEM diameter high performance slotted rotors for your 4WD or truck – Made in South Africa.
- An axle set of matched PB05 high-performance brake pads – Made in Japan.
- Fits as per a standard rotor and pad change, using the vehicle’s original calipers.
$810.00 Add to cart -
Performance Upgrades - FJ Cruiser LateShips FREE !!
within 48 US StatesPowerbrake D-Line HP Rotor and Pad Kit | FJ Cruiser Front
- Suits Toyota FJ Cruiser 2006-2014 Front
- Also available for the REAR
- Powerbrake D-Line Features
- Rotors are cast from a proprietary high carbon cast-iron alloy.
- Rotors are machined to tolerances up to three times tighter than the industry norm.
- All Powerbrake rotors feature our MTR (Max Temperature Recording) system.
- Proprietary black disc surface coating ensures quicker bed-in and max brake performance.
- Spiral slots on the rotor fiction surface clear friction gasses, debris and water.
- Matched high friction PB05 brake pads take the guesswork out of pad selection.
- Pad compound PB05 is manufactured in Japan and has been specifically formulated for use on 4×4 vehicles
- Powerbrake D-Line Benefits at a Glance
- Reduced stopping distances in both wet and dry conditions.
- Reduced brake fade and improved brake consistency.
- Improved initial brake response (bite).
- Improved brake modulation particularly during emergency stops.
- Improved resistance to rotor distortion (warping) and cracking at high temperatures.
- What’s Included in Powerbrake D-Line?
- 2 x Standard OEM diameter high performance slotted rotors for your 4WD or truck – Made in South Africa.
- An axle set of matched PB05 high-performance brake pads – Made in Japan.
- Fits as per a standard rotor and pad change, using the vehicle’s original calipers.
$810.00 Add to cart -
TimbrenShips FREE !!
within 48 US StatesTimbren Bump Stops Front & Rear | FJ Cruiser
- Suits 2006-2014 Toyota FJ Cruiser
- Includes both Front and Rear bump stops for the whole vehicle
- Active Off-Road Bumpstops provide off-road enthusiasts greater control over their vehicles’ suspension travel. Using progressive-rate springs means that instead of a hard stop at the end of axle travel the axle energy will be absorbed when bottoming-out producing smooth, predictable, and quiet axle engagement and disengagement.
- Unlike OEM bump stops, Active Off-Road Bumpstops are made from natural rubber. Just like our Timbren SES line, Active Off-Road Bumpstops carry a lifetime warranty and a satisfaction guarantee.
- ABSTORSEQ replaces the rear OEM bump stops and ABSTOF replaces the fronts on the FJ Cruiser. Upgrade to Active Off-road Bumpstops and experience the difference.
- Maintain Full Axle Travel
- Smooth Axle Engagement and Disengagement
- Enhance Suspension Performance
- Progressive Spring Rate
- Absorbs Energy and Cushions Road Shocks
- Stronger Than OEM Bumpstops
- Easy Installation
- Satisfaction Guarantee
- Lifetime Warranty
- Front Instructions and Rear Instructions
$538.72 Add to cart -
FJ Cruiser Late (2010-2014)
Dobinsons 2-3.5″ Extended Travel Pre-Assembled IMS Coilovers for FJ Cruiser 2010+
- Suits 2010-2017 Toyota FJ Cruiser 4×4 Models
- Looking for a quick and easy way to lift your FJ Cruiser? This is your answer
- A 4×2 model lifts 1″ extra with the 4×4 lift heights
- Select your desired lift height and spring rate – we’ll take care of the rest!!
- Dobinsons IMS are height adjustable by a fully threaded body
- The Dobinsons IMS Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- Extended Travel – 575mm fully extended, 430mm compressed
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
- Instructions for setting coil seat height
- To run these Extended Travel coilovers, new UCA’s need to be added for proper articulation and correct wheel alignment. A diff drop kit is also recommended to minimize CV binding at full droop
- Click to see Matching rear shocks
$1,165.00 Select options -
FJ Cruiser Late (2010-2014)
Dobinsons 1.5-2.5″ Pre-Assembled IMS Coilovers for FJ Cruiser 2010+
- Suits 2010-2017 Toyota FJ Cruiser 4×4 Models
- Looking for a quick and easy way to lift your FJ Cruiser? This is your answer
- A 4×2 model lifts 1″ extra with the 4×4 lift heights
- Select your desired lift height and spring rate – we’ll take care of the rest!!
- Dobinsons IMS are height adjustable by a fully threaded body
- The Dobinsons IMS Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- 560mm extended, 420mm compressed
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
- Instructions for setting coil seat height
- Note about lift heights – all vehicles can have some variance and desired lift height may need to be adjusted to suit your specific vehicle. Adding 2.5″ or more lift, new UCA’s should be added for proper articulation and correct wheel alignment
- Click to see Matching rear shocks
$1,165.00 Select options -
Snorkel
Safari Snorkel for Toyota FJ Cruiser Snorkel 2010-2016
- Suits Toyota FJ Cruiser 2010-2016
- Safari V-Spec Snorkel
- Relocates Your Engine’s Air Intake Point to a Higher Location
- Crosslinked Polyethylene Construction
- Built to Perform in Extreme Weather Conditions
- Comes With Stainless Steel and Plated Hardware
- Bolt-On Installation; Drilling Is Required
- Supported by a 2-Year Warranty
- Fully Designed and Manufactured in Australia
- Designed and manufactured in Australia
- Requires cutting and drilling of the fender and A-pillar. Full instructions and template provided.
$546.00 Add to cart -
Sale!FJ Cruiser Late (2010-2014)
RCI 2010+ FJ Cruiser Engine Skid Plate
- Fits Toyota FJ Cruiser 2010-2017 models
- Includes front skid plate ONLY
- Protects front two cross-members, low hanging front differential, oil pan, transmission, second and third cross-members, exhaust cross pipe, and transfer-case
- Excellent addition or replacement of weak, lightweight OEM skid plates
- Simple installation and removal of all subsections for maintenance
- Built in oil drain holes allow easy access and ability to change oil without removal of plate
- Engine skid plates come standard with center mounting posts for substantially increased strength
- Engine skid plate includes differential drop cage for maximum security and ground clearance, PLUS this feature allows the use of differential drop kits without having to space the skid plate down
- Reinforced edges between cross-members for maximum strength and rigidity
- Bolt protector rings surround exposed bolts, shielding against physical damage
- Smooth, flat surface that easily slides over obstacles
- Black powder coat finish is standard on steel skid plates for a rust resistant, durable and high quality finish, optional on aluminum
- Installs in minutes
- Grade 8 hardware and installation instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- Made in the USA
Original price was: $369.99.$333.00Current price is: $333.00. Select options -
Sale!4Runner 4th Gen (2003-2009)
RCI 4th and 5th Gen 4Runner + FJ Cruiser V6 Transmission Skid Plate
- Fits Toyota 4Runner V6 Models 2003-2009 and 2010-2024, and FJ Cruiser (all years)
- Protects transmission, second and third cross-members, and exhaust
- Excellent addition or replacement of weak, lightweight OEM skid plates (which do not provide any coverage over transmission)
- Service openings for maintenance without removal
- Reinforced edges between cross-members for maximum strength and rigidity
- Bolt protector rings surround exposed bolts, shielding against physical damage
- Built in drainage holes, which also help prevent suction of skid plates in mud and snow
- Smooth, flat surface that easily slides over obstacles
- Black powder coat available for rust resistant, durable and high quality finish
- Installs in minutes
- All hardware and installation instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- Made in the USA
Original price was: $239.99.$216.00Current price is: $216.00. Select options -
Sale!BilsteinShips FREE !!
within 48 US StatesBilstein 47-309975 Front 6112 Series Kit
Original price was: $966.21.$826.00Current price is: $826.00. Read more -
BrakesShips FREE !!
within 48 US StatesPowerbrake X-Line 4×4 FJ Cruiser Big Brake Kit Stage 1
Toyota FJ Cruiser Big Brake Kit (all years) Includes:
- X-Line billet 6-piston off-road calipers (pair)
- High-performance brake pads, pre-loaded into the calipers
- 1-Piece 350mm x 34mm (13.77″ x 1.33″) 48-vane discs
- Curved, directional cooling vanes
- Billet caliper mounting brackets
- Stainless steel braided brake lines
- All necessary mounting hardware for quick, easy bolt-on installation
- Comprehensive fitment and bed-in instructions
- Manufactured, finished and packaged 100% in South Africa
- Now Includes Upgraded Powerbrake Pads, PB05 Compound – highest level 4×4 brake pads available – made in Japan
- REQUIRES 17″ WHEELS FOR ADEQUATE CALIPER CLEARANCE
- Check out the rear brake upgrade also for 06-09 Models and 10-16 Models
$2,675.00 Select options -
Full Suspension Kits - FJC LateShips FREE !!
within 48 US StatesDobinsons 2.5-3.5″ Extended Travel Pre-Assembled MRA FJ Cruiser Coilovers for 2010-2014
- Suits Toyota FJ Cruiser 2010-2014
- Looking for a quick and easy way to lift your FJ Cruiser? This is your answer
- Select your desired lift height and spring rate – we’ll take care of the rest!!
- Dobinsons MRA are height adjustable by a fully threaded body
- MRA59-A574 – 575mm extended, 420mm compressed
- The Dobinsons MRA Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- Extended Travel – 567mm extended, 417mm compressed
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
- Resi installation instructions
- To run these Extended Travel coilovers, new UCA’s need to be added for proper articulation and correct wheel alignment. A diff drop kit is also recommended to minimize CV binding at full droop
- Link to Matching rear shocks
$1,795.00 Select options
