Your cart is currently empty!
Tacoma 2nd Gen (2005-2015)
Showing 91–120 of 150 results
-
ARB
OME 2886 Front Coil Springs | Toyota Lexus Trucks SUV’s
- OME Part Number 2886
- Bar Size : 17.5mm
- Free Height : 402mm
- Number of Turns : 10.6
- Coil Weight (each): 5.9 Kg | 13 lbs
- Spring Rate : 660 lbs
- Sold in Pairs
$214.00 Add to cart -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD111 Front Air Locker Toyota Lexus 8″ IFS 30 Spline 3.91+
- For Use With Toyota 8″ IFS Clamshell differential with 30 Spline Axles and 3.91 And Up FactoryGears
- Usually all models that came with an automatic transmission used 3.91+ gear ratios, but some more modern Toyota and Lexus use 3.73 gears from the factory
- Factory R&P may use either RD111 or RD121 depending on ratio. All known aftermarket R&P sets suit RD121.
- If you are changing to aftermarket gears, check with that gear manufacturer on which gears to order
- Full vehicle fitment list is further down in the main description, includes 4Runner, Tacoma, FJ Cruiser, GX470, GX460
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Select options -
Accessories
Dobinsons Pickup Rear Drawers Kit with Fridge Slide Universal Fit
- 1.6mm Zinc Plated Robust Steel Construction
- 12mm Heavy Duty Plywood Panels with Marine Carpet Covering
- Built in Heavy Duty Fridge Slide
- 8 x Heavy Duty Stainless Steel Tie Down Points
- Requires tonneau cover or canopy
- Universal Mount, measures 51.1 x 39.4 x 10 inches (L, W, H), requires drilling of truck bed, and custom fitting of side panels (if ordered)
- You can add a universal side wing panel kit down below, so that you can build out the edges of the drawers to the side of your bed
- Aluminum Edging Protection
- Heavy duty lockable latches
- Marine Carpet
- Massive 150KG (330LB) Drawer Capacity on Heavy Duty Roller Bearing System
- Ships to the nearest freight terminal for pickup, unless home delivery is option is added below. We will be in touch to let you know the terminal location
From $1,845.00 Select options -
Suspension
3″ Tacoma Lift Kit Builder for 2005 to 2023 4×4 Models
- 4×4 Access Cab models come with 1″ front lift from the factory. Lift heights listed are for Dual cab 4×4 models. Subtract 1″ for access cab models
- Long bed models require the next step up in leaf spring, or they will sit 1″ less high
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Select from one of 3 rear leaf spring packs from All Pro Offroad, add up the total constant weight in the back of your Tacoma to make the right choice
- Choose from Teal, Black or Red Coil Springs
- Dobinsons Coils are specifically suited to the additional accessory load (weight) on the vehicle
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel – Choose from IMS or MRA
- IMS Shock Details
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Fully Rebuildable Design – no set rebuild period or limits
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- MRA Shock Details
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- Extended Travel – 567mm extended, 417mm compressed
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design – no set rebuild period or limits
- Includes Bolt-on Reservoir Brackets and Hardware and Adjuster Wrench
- Choose your desired suspension parts to build the kit best suited to your weight and desired lift height
- You choose what parts you want to buy. If you don’t add it to your cart, it’s not included
- Common installation instructions related to parts on this page
From $2,479.00 Select options -
Leaf Springs - Tacoma 3rd GenShips FREE !!
within 48 US StatesAll Pro 2005-2023 3.0″ Tacoma Leaf Springs – Expedition 2.0 1000LBS
- Suits 2005-2023 Toyota Tacoma 4×4 Models
- Expedition Version 2.0 Leaf Springs give 3.0″ of lift with 1000LBS of added constant load, less lift with more weight
- Number of leaves 9+1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 54-3/8″ (1381 mm)
- Spring Rate: 248lbs/in
- A higher number of thinner leafs provides a smoother, progressive spring rate compared to fewer, thicker leaves.
- Number of Leaves: 9 + 1 Overload/Rebound
- Double “military” wrap provides extra strength for the main leaf
- Eyelet-to-Eyelet Length (Free): 54-3/8″ (1381 mm)
- “Torque Leaf”, an extra half-leaf at the top of the spring pack, increases anti-wrap properties without hindering travel or ride quality.
- Diamond-cut leaf ends to eliminate stress points which may weaken leafs and lead to premature failure
- Teflon anti-friction pads between leafs provide smoother flex, lessen spring wear and reduce noise
- Leafs are shot-peened after forming to relieve stress.
- Every completed spring pack is pre-cycled to their travel extremity for quality control and to reduce the likelihood of initial sag.
- All-Pro leaf springs are sold in pairs, with a complete urethane bushing and sleeve kit.
- Spring Rate: 151 lbs/in for Standard, 207 lbs/in for Expedition, and 248 lbs/in for Expedition 2.0 Leaf Springs
- After installation, the stock rear bumps will no longer be sufficient to prevent the spring from inverting. You must purchase and install a set of bump stops that are of sufficient height to prevent the spring from going negative arch. For best results, we recommend Wheeler’s SuperBumps (sold separately). WOR-306957
- 4″ Extended brake lines – recommended at this lift height
- Requires a suitable 3″ lift shocks to go with them, such as IMS59-50941 or MRA59-A941
- Sold in Pairs
- Made in USA
$979.00 Add to cart -
Leaf Springs - Tacoma 3rd GenShips FREE !!
within 48 US StatesAll Pro 2005-2023 3.0″ Tacoma Leaf Springs – Standard
- Suits 2005-2023 Toyota Tacoma 4×4 Models
- Standard Leaf Springs give 3″ of lift with up to 200LBS of added load, less lift with more weight
- Long bed models may lift less due to extra weight and load on the springs
- Number of Leaves: 10 + 1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 54-3/8″ (1381 mm)
- Spring Rate: 151 lbs/in for Standard
- A higher number of thinner leafs provides a smoother, progressive spring rate compared to fewer, thicker leaves.
- Number of Leaves: 9 + 1 Overload/Rebound
- Double “military” wrap provides extra strength for the main leaf
- Eyelet-to-Eyelet Length (Free): 54-3/8″ (1381 mm)
- “Torque Leaf”, an extra half-leaf at the top of the spring pack, increases anti-wrap properties without hindering travel or ride quality.
- Diamond-cut leaf ends to eliminate stress points which may weaken leafs and lead to premature failure
- Teflon anti-friction pads between leafs provide smoother flex, lessen spring wear and reduce noise
- Leafs are shot-peened after forming to relieve stress.
- Every completed spring pack is pre-cycled to their travel extremity for quality control and to reduce the likelihood of initial sag.
- All-Pro leaf springs are sold in pairs, with a complete urethane bushing and sleeve kit.
- Spring Rate: 151 lbs/in for Standard, 207 lbs/in for Expedition, and 248 lbs/in for Expedition 2.0 Leaf Springs
- After installation, the stock rear bumps will no longer be sufficient to prevent the spring from inverting. You must purchase and install a set of bump stops that are of sufficient height to prevent the spring from going negative arch. For best results, we recommend Wheeler’s SuperBumps (sold separately). WOR-306957
- 4″ Extended brake lines – recommended at this lift height
- Requires a suitable 3″ lift shocks to go with them, such as IMS59-50941 or MRA59-A941
- Sold in Pairs
- Made in USA
$979.00 Add to cart -
FoxShips FREE !!
within 48 US StatesFox 2.5 Factory Race Series Coilover IFP Shock Set – 883-02-025
- Suits 5th Gen Toyota 4Runner 2010-2024 0-3″ lift
- Suits 4th Gen Toyota 4Runner 2007-2009 0-3″ lift
- Suits Toyota FJ Cruiser 2006-2016 0-3″ lift
- Suits Toyota Tacoma 4×4 2005-2015 0-3″ lift
- Suits Toyota Tacoma 4×4 2016-2023 0-2″ lift
- Suits Lexus GX470 all years 0-3″ lift
- Suits Lexus GX460 all years 0-3″ lift
- Sold as a Pair, enough for 1 vehicle
- Preassembled with coil and strut mount – full assembly ready to bolt in
- Coilovers comes preset to the taller lift height right out of the box – may need to adjust depending on added weight or engine size
- Includes a 600LB spring rate coil
- Can not be used with any Dobinsons coils
- Front coilover shocks
- For up to 3 inch lift
- 2.5 inch smooth bore zinc plated seamless steel body
- Zinc-plated and double-clear coated body for long lasting finish
- Internal IFP mono-tube reservoir design separates shock oil from the high-pressure nitrogen
- Black-anodized, CNC-machined 6061-T6 billet aluminum components
- Application specific, adjustable 3.0 Eibach® racing springs
- 7/8″ hardened NitroSteel® Steel carbon shafts
- 6061-T6 hard-anodized, high flow aluminum piston
- Application specific valving to maximize performance
- Redundant sealing pack system main seal, wiper seal, scraper seal
- JM92 Advanced Suspension Fluid for improved performance at variable temperatures
- PTFE-lined, heat-treated, alloy steel spherical bearing
- Ride height preload ring adjustment
- Extended: 22.52 in.
- Collapsed: 17.58 in.
- Stroke: 4.93 in.
- Top mount: OEM
- Bottom mount: eyelet
- Sold in pairs
- Note: requires aftermarket upper control arms
- Installation Guide
- Link to buy Preload Wrench
- Link to buy Back Up Wrench (remove preload)
- Exploded View Diagram
- Warranty Information
$1,499.95 Add to cart -
ARB
OME 2884 Front Coil Springs | Toyota Lexus Trucks SUV’s
- OME Part Number 2884
- Bar Size : 16.5mm
- Free Height : 390mm
- Number of Turns : 9.75
- Coil Weight (each): 4.7 Kg | 10.3 lbs
- Spring Rate : 590 lbs
- Sold in Pairs
$214.00 Add to cart -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD129 Rear Air Locker Toyota 8.4″ 30 Spline
- For Use only with Toyota 8.4″ 12 Bolt 30 spline Rear Axle
- Suits multiple vehicles, the full list is down below. Used in older Tacoma, Sequoia, Tundra and T100 Trucks.
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Add to cart -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD121 Front Air Locker Toyota Lexus 8″ IFS 30 Spline 3.73-
- For Use With Toyota 8″ IFS Clamshell differential with 30 Spline Axles and 3.73 And Down Factory Gears
- Usually all models that came with a manual transmission used 3.73- factory gear ratios, but you must check before ordering
- Factory R&P may use either RD111 or RD121 depending on ratio. All known aftermarket R&P sets suit RD121.
- If you are re-gearing, check with the gear manufacturer for which Air Locker to order
- Full vehicle fitment list is further down in the main description, includes 4Runner, Tacoma, FJ Cruiser, GX470, GX460
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Select options -
Snorkel
Safari Snorkel SS171HP – Toyota Tacoma 2nd Gen 2005-2015
- Suits Toyota Tacoma 2005-2015 Models – 2nd Gen Tacoma
- Raises air intake to prevent water ingestion, while also allowing vehicles to utilize clean air when driving in dusty conditions.
- Vehicle specific design and factory airbox adaption fitment.
- Manufactured using durable, UV stable cross linked polyethylene material.
- Supplied as a comprehensive kit, including the necessary fasteners and mounting brackets.
- Unique air ram design acts as a highly efficient water separator to remove rain water form incoming air stream.
- Designed and manufactured in Australia
- 10% higher CFM for this application over other brand snorkels, due to large body design
- Requires cutting and drilling of the fender and A-pillar. Full instructions and template provided.
$627.00 Add to cart -
Bump StopsShips FREE !!
within 48 US StatesDobinsons 2.2″ Hydraulic Bump Stop IFS Weld on Mount Kit
- Kit includes front Weld on Mounts (Pair) and Dobinsons HBS56-009 Pair of Hydro Bump Stops
- Made for IFS (independent front suspension) vehicles to replace the OEM rubber bump stop
- HBS56-009 – 56mm (2.2″) body | 46mm (1.8″) stroke | 188mm (7.4″) extended | 142mm (5.6″) compressed | 105mm (4.0″) thread length
- CNC Machined 50mm Billet Aluminum Piston
- EDP Coated 3mm Thick 56mm Steel Body
- Threaded Body For Height Adjustment
- Supplied with both Interchangeable Super Quiet Rubber Rod End & Hard Nylon
- 30mm Micro Polished Hard Chrome Shaft
- Slow Rebound Valving To Prevent Bucking
- Removable Dust Cover Boot For Stealth Appearance
- Fully Rebuildable & Tunable
- O-Ring Travel Indicator
- Heavy Duty Extreme-Race style Triple Seal Design
- Nitrogen Gas Charged & Tunable (100 to 300 PSI)
- Pre-charged to 150 PSI
- Extra Short Dead Lengths For Compact Fitment
- Universal design threaded weld on bump stop can to hold the 2.2″ body bump stop
- Cans have 3mm walls for increased strength
- Kit is ideal for those who bottom out often in their offroad driving or go really hard at high speeds
- Could suit a wide range of vehicles as listed below, but remember they are universal and will require adaptation to your vehicle and welding
- Custom fitting and welding is required
- Photo attached shows these bump stops installed with the weld-on mounts on a 3rd Gen Tacoma
From $1,090.00 Select options -
Bump Stops
Dobinsons 2.2″ Hydraulic Bump Stop IFS Weld on Mounts
- Universal design threaded weld on bump stop can to hold a 2.2″ body bump stop
- Intended to be used with the Dobinsons HBS59-009 Hydro bumps
- 3mm walls for increased strength
- Sold as a pair
- Ideal for those who bottom out often in their offroad driving or go really hard at high speeds
- Could suit a wide range of vehicles as listed below, but remember they are universal and will require adaptation to your vehicle and welding
- Custom fitting and welding is required
$400.00 Add to cart