Your cart is currently empty!
Shop
Showing 421–450 of 2002 resultsSorted by popularity
-
Sequoia 1st Gen (2001-2007)FREE SHIPPING
within 48 US StatesDobinsons 1.75-2.5″ Sequoia Suspension Kit for 2001-2007 4.7L V8
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base Kit Includes 2 Front Struts, 2 Rear Shocks, and 4 Coil Springs
- Additional parts can be added from the drop down menus
- All 3 different Dobinsons shock types are available to choose from below
(9 reviews) -
Suspension
Alignment Cam Gussets | Tacoma 4Runner FJ Cruiser GX470 GX460
- Suits 2005-23 Toyota Tacoma, 2003-2024 4Runner, 2007-16 FJ Cruiser, Lexus GX470, GX460
- The Dirt King alignment cam gussets replace the weak factory cam tabs which commonly bend resulting in the vehicle being out of alignment
- Alignment techs famously get the cam out of position and crank it down against the factory tabs, bending them
- The kit is made from 1/8″ and 3/16″ thick chromoly plates
- Installation requires removing the factory cam plates and welding on the Dirt King cam gussets in it’s place
- Made in the USA
(0 reviews) -
Suspension
Dobinsons Upper Coil Spring Isolator Pair
- Adapter upper strut mount isolators to run Dobinsons C59-300, C59-302 or C59-314 coils on GS59-222, IMS59-50222 or MRA59-A222 struts on 1st Gen Tundras and Sequoias
- Not needed if using C59-344 coils
- Also, these fit the SC59-001 and SC59-002 strut mounts to replace those pieces if necessary
- Sold as a set, 2 pieces, enough for 1 vehicle
- Made of natural rubber
- Assemble To Chassis Same Way As OEM
- Maintains Factory Ride Characteristics
(4 reviews) -
Coil Springs - 4th Gen 4Runner
Dobinsons Front Coil Spring Options for V8 Toyota 4th Gen 4Runner 2003-2009 – Pair
- THIS IS FOR V8 ENGINE 4X4 MODELS ONLY – V6 models use a different set of specs
- Choose what coil suits your vehicle and needs the best
- Sold as a Pair
- All specs are listed for 4×4 models. 2WD models lift about 1″ more due to less weight
- Stock weight = all stock front end | 110 LBS is usually a slim line bumper and winch with synthetic line | 220 LBS is usually a full width steel bumper with a winch and synthetic or steel line | 300+ LBS is usually a full with steel bumper, winch, dual batteries, and skid plates
- C59-238 – Stock front end, low height 1/4-1/2″
- C59-296 – Stock front end, 1.0″ lift
- C59-300 – Stock front end, 1.5″ lift
- C59-302 – Stock Weight – 2.0″ | with 110-150lbs – 1.5″
- C59-314 – Stock Weight – 2.5″ | with 110-220lbs – 2.0″
- C59-350 – With 220-300lbs – 1.5″ | Heavy rate coils
- C59-352 – With 110-220lbs – 2.0″ | Heavy rate coils
- C59-354 – 2.5″ with 110-150lbs | with 220-300lbs – 2.0″ | Heavy rate coils
(12 reviews) -
Rear Drawers
Dobinsons Rear Drawer Table Top – 18.75″ Wide
- 1.5mm Stainless Steel Construction
- 24.75″ x 18.75″ added work space
- Laser cut towel hangers and bottle opener
- Works with drawer open or closed, inside or out!
- Drawer system not included
- Suits RD80-1000 and RD80-1003 – each drawer is 18.75″ Wide
- Suits drawers that go into Land Cruisers
(3 reviews) -
Sale!TJ Wrangler (1996-2006)FREE SHIPPING
within 48 US StatesKing 4WD Premium TJ Wrangler Soft Upper Door Windows Tinted 1996-2006
- Suits 1997-2006 Jeep Wrangler TJ 2-door soft top convertibles (and LJ Unlimited) with Factory Half Door and Soft Door Uppers
- Does not include any framework
- Includes left and right side windows
- Black Diamond Fabric with TINTED windows
- Black Diamond Fabric
- Specification: Two Layer 24oz Marine Grade – Waterproof
- Testing: CFFA, FMVSS & SAE Requirements
- Specification: UV Approved
- Testing: Accelerated Light Aging Test – 1000 Hours
- Window Glass
- Specification: 96g DOT Approved Pressed flexible vinyl, undistorted, won’t shrink or yellow
- Testing: CFFA, FMVSS & SAE Requirements
- Zippers
- Specification: Reinforced nylon self-correcting zippers
- Testing: 50,000 Cycle Test – No bind or drag
- Velcro
- Specification: Industrial Grade Fiber
- Testing: 150 kg (330 lbs.) per square inch
- Seams
- Specification: 135-gauge thread with heat sealed seams, 4-piece thread per inch
- Testing: CFFA, FMVSS & SAE Requirements
- Also available with Clear Windows (not tinted)
- We also sell a full soft top with replacement soft half door uppers as well, click for details
(7 reviews) -
Sequoia 3rd Gen (2023-2025+)
Dobinsons Rear Coil Spring Options | Toyota Sequoia 2023+ – Pair
- Suits Toyota Sequoia 2023-2025+, choose the appropriate lift height that also matches any added weight you’ve put on the car
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Coils are Sold in Pairs
- Lifting the rear 2″ requires a new Panhard Rod to re-center the axle
- Lifting 1″ or more, new rear sway bar links are necessary
- 2″ of rear lift also requires longer shocks than stock
(14 reviews) -
BrakesFREE SHIPPING
within 48 US StatesPowerbrake X-Line 80 Series Land Cruiser Front Big Brake Kit (17″+ Wheels) 1990-1997
1990-1997 Toyota Land Cruiser 80 Series and Lexus LX450 Big Brake Kit Includes:
- This is the kit for 17″+ Wheels. There’s a different kit for 16″ wheels
- X-Line billet 6-piston off-road calipers (pair)
- High-performance brake pads, pre-loaded into the calipers
- 2-Piece 13.7″ x 1.34″ 72-vane discs
- Semi-float disc drive system allows for radial disc expansion and contraction
- Curved, directional cooling vanes
- Billet caliper mounting brackets
- Stainless steel braided brake lines
- Provided brake lines connect the caliper to the axle housing, then extended brake lines (sold separately) can be used as well for taller lift kits, connecting from the axle to the frame
- All necessary mounting hardware for quick, easy bolt-on installation
- Comprehensive fitment and bed-in instructions
- Now Includes Upgraded Powerbrake Pads, PB05 Compound – highest level 4×4 brake pads available – made in Japan
- Manufactured, finished and packaged 100% in South Africa
- REQUIRES 17″ WHEELS FOR ADEQUATE CALIPER CLEARANCE
(11 reviews)$3,800.00 Select options This product has multiple variants. The options may be chosen on the product page -
200 Series Land Cruiser (2008-2021)FREE SHIPPING
within 48 US StatesDobinsons Adjustable Rear Lower Control Arms Pair | WA59-547K
- Suits all 200 Series Land Cruisers from 2008-2021, 300 Series Land Cruiser, 2023+ Toyota Sequoia, 2024+ Land Cruiser 250 Series, Lexus GX550
- Comes with high quality rubber OE style bushings installed for maximum flexibility, and zero noise
- Made from HSLA (High Strength Low Alloy) Steel
- 40mm OD and 6mm wall thickness with support brace
- Oversized adjusters and rod thickness for maximum strength and durability with double-nut locking feature
- Zinc plated, then E-coated black, for the ultimate finish and protection
- Sold as a pair
(4 reviews) -
Tundra 3rd Gen (2022-2025+)
Dobinsons 2.5″ Lift Rear Coil Springs for Toyota Tundra 2022+ – Pair
- Suits Toyota Tundra 2022-2025+, lifts the rear 2.5″ with stock weight (no accessories)
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
- Installation Note: Transfer over the OEM coil isolators from the stock coils to these to prevent coil slap
- Will not work with stock shocks, they’re not long enough. Click here to see shock options
- Stock base model shocks are ok with 1″ lift but they’re not very long. TRD Pro rear shocks are ok for up to 2″ of lift
- 485/495mm free height, 227 LB spring rate
(8 reviews) -
Full Suspension Kits - 5th Gen 4RunnerFREE SHIPPING
within 48 US StatesDobinsons 1-2.5″ Pre-Assembled IMS Coilovers for Toyota 4Runner 5th Gen 2010-2024
- Suits 2010-2024 Toyota 4Runner 5th Gen 4×4 Models
- Looking for a quick and easy way to lift your 4Runner? This is your answer
- A 4×2 model lifts 1″ extra with the 4×4 lift heights
- Select your desired lift height and spring rate – we’ll take care of the rest!!
- Dobinsons IMS are height adjustable by a fully threaded body
- The Dobinsons IMS Coilovers will come pre-assembled to the selected height with new struts, coils and top mounts
- Fully rebuildable and re-valvable
- 560mm extended, 420mm compressed
- SOLD IN PAIRS – READY TO BOLT IN
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Photos for illustration purposes
- Instructions for setting coil seat height
- Note about lift heights – all vehicles can have some variance and desired lift height may need to be adjusted to suit your specific vehicle. Adding 2.5″ or more lift, new UCA’s should be added for proper articulation and correct wheel alignment
- Click to see Matching rear shocks
- Please NOTE: Assembled coilovers cannot be returned, as they are made to order
- Lift heights are based on the standard 20″ front and 22″ rear, measured from the center of the hub up to the fender edge. Many vehicles come in at different heights from the factory based on trim levels and options
(7 reviews) -
80 Series Land Cruiser (1990-1997)FREE SHIPPING
within 48 US StatesDobinsons 3-Way Adjustable MRA 0-3.5″ MRA Lift Kit | Land Cruiser 80 Series 1990-1997
- Suits Land Cruiser 80 Series and Lexus LX450
- Complete MRA suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to match OE fitment specs
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base kit includes front and rear coils and shocks, you can add any other parts you need
- Choose your coils and load carrying ability, anywhere from 0″ up to 3.5″ of Lift
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- External Remote Oil Reservoir with dual speed compression adjustment
- Single Piece Lower Leg, Natural Rubber Bushings Top and Bottom
- Triple Lip Oil Seal for Superior Lifespan
- Direct Bolt-on, Fully Rebuildable Design
- Pre-Charged with Nitrogen, Ready to be Assembled and Installed
- EDP Surface Protection, 3mm Heavy Duty Wall Thickness
- Includes Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Installation Instructions of the MRA Shocks
- Full 2 year limited warranty, no set rebuild time period
(12 reviews) -
GX460 (2010-2023)
RCI Gas Tank Skid Plate | 4th & 5th Gen 4Runner GX470 GX460 2003-2024
- Fits all Lexus GX470 and GX460 Models, and all 4th and 5th Gen Toyota 4Runner 2003-2024
- Black powder coat available for rust resistant, durable and high quality finish
- Simple bolt on installation
- All hardware and instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling
- Smooth, flat surface that easily slides over obstacles
- Material: 3/16” Steel or 1/4” 5052 Aluminum Alloy
- Weight: 3/16” Steel- 52lbs. Aluminum- 26lbs.
- Finish: Heavy Duty Black Powder Coat or Bare Metal
- Made in the USA
(7 reviews) -
SuspensionFREE SHIPPING
within 48 US StatesDobinsons GS59-632 Front Twin Tube Shocks Pair | 70 Series
- For 1/90 to 5/93 Toyota 70 Series models, LJ70 LJ72 LJ73 LJ77 with Square Headlights
- Also suits 1994+ RJ70, RJ73, KZJ 70/71/73 with Square Headlights
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals, Fuchs German shock absorber oil, Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- Matched to compliment Dobinsons Complete Suspension Systems
(10 reviews) -
Gladiator JT (2020-2025+)
Jeep Gladiator Long Range Auxiliary Fuel Tank (17gal) 2020+ 3.6L V6
- Suits Jeep Gladiator JT Trucks from 2020-2024 onwards with the 3.6L V6 Gas engine
- Not suitable for Diesel versions
- This is an additional tank that fits on the left side of the driveshaft, it holds 17 gallons, and uses a transfer pump to fill your main tank when you hit a switch
- 17 gallon capacity, fits on opposite side of OE gas tank for maximum clearance!!
- 17 gallons plus your original 22 gallon tank gives you a capacity of 39 gallons in total!!
- Tank fills using the OEM gas door and supplied parts
- Tank uses a transfer pump to fill the main tank, 2L per minute pump rate
- Exhaust modification required – exhaust needs to be replaced with aftermarket/custom or available LRA replacement exhaust kit listed below (tank goes where OE exhaust was routed). Exhaust kit components
- Fitting time – approximately 5.5 hours
- Part Number JGJTPA
- Fitting Instructions – Intended to be installed by a certified mechanic
- This item ships on a pallet to the nearest Truck Freight terminal for you to pickup. We will be in touch with you regarding the nearest freight terminal, unless you add home delivery fee below.
- This product can not be sold or shipped to residents in California, as it will not pass SMOG. Do not order this product if you live in California!!
- MADE IN AUSTRALIA
- Nearest Freight Terminal Finder – Use this to decide if you want home delivery or pickup at the nearest terminal
(5 reviews) -
Skid PlatesFREE SHIPPING
within 48 US StatesARB 5421100 Skid Plate Kit | Toyota 4Runner 4th Gen 2003-2009
- Suits all Toyota 4Runner 4th Gen models from 2003 to 2009. Also fits 5th Gen 4runners without KDSS
- You must check to make sure you don’t have KDSS before ordering this kit
- 3mm pressed and folded sheet steel adds more strength than a standard folded sheet.
- Laser cut sheet steel.
- Zinc plated and powder coated with a silver textured finish.
- Recessed mounting bolts are protected and easy to remove for vehicle servicing.
- The Under Vehicle Protection will fit with or without an ARB front bumper. Fitment has not been confirmed with other aftermarket bumper designs
- Comprises 4 panels: Front Panel (Protects power steering, engine sump, sway bar), Diff Panel (Protects front diff mounts, engine sump), Transmission (Protects transmission and transmission controls) and Transfer Case (Protects transfer case)
- See more details below as well as product video
(8 reviews) -
Dobinsons
Dobinsons SP59-023 Greasable Pin Kit (Pair) | Land Cruiser 70 Series
- Suits all 70 Series models with leaf spring rear ends, including 70, 73, 74, 75, 77
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Purchase includes 1 pair (2 pieces) of greasable pins for the fixed end of a leaf spring
- Photo for reference only, actual product may appear different
(5 reviews) -
KL Cherokee (2014-2022) (Trailhawk)
Dobinsons C29-151 Rear Lifted Coils for 4X4 Jeep Cherokee KL 2014 to 2022 – Pair
- Trailhawk (AD2) lifts 1.0″ rear. Sport (AD1) models lift 2″ rear
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Can be used with Dobinsons heavy duty Twin-tube Nitrogas Struts
- Sold as a pair
- Powder coated in a long lasting black color
(5 reviews) -
Air CompressorsFREE SHIPPING
within 48 US StatesARB CKMTA12 12V High Performance Twin Air Compressor
- Motors are water sealed, 100% ball bearing equipped (i.e. no bushings), and feature a unique linear brush pre-load system for extra long life, low heat and quiet operation throughout the life of the unit.
- Compact twin motor, dual cylinder design makes it the highest flowing compressor in its class (voltage vs. size). Highest air flow rate of any 12V compressor of its size on the market at 174LPM [6.16CFM].
- Full wiring loom included for simplified installation and easy plug-in connectivity to Air Locker control solenoids. (Note: Air Locker Manifold Kit #171503 required to mount solenoids).
- Motors are internally thermal protected against extreme temperature damage. Over-pressure safety valve equipped. Equipped with dual heavy duty Maxi-Fuses for professional in-line circuit protection and true circuit redundancy in case of a fault.
- Compressor pistons are equipped with a heavy duty European made cylindrical roller bearing. Hard-anodized cylinder bores and PTFE (Teflon) impregnated carbon fibre piston seals for reduced friction and maximum trouble free life.
- 12V, Draws 50 Amps max, 6.16 CFM, 150 PSI max, 100% Duty Cycle
- 10.9 x 7.5 x 4.1 inches actual dimensions, 19.4 LBS with all items included
(4 reviews) -
SnorkelFREE SHIPPING
within 48 US StatesSafari Snorkel SS450HP – Toyota 4Runner 5th Gen 2010-2024
- Suits Toyota 4Runner 5th Gen models from 2010 to 2024
- Raises air intake to prevent water ingestion, while also allowing vehicles to utilize clean air when driving in dusty conditions.
- Vehicle specific design and factory airbox adaption fitment.
- Manufactured using durable, UV stable cross linked polyethylene material.
- Supplied as a comprehensive kit, including the necessary fasteners and mounting brackets.
- Unique air ram design acts as a highly efficient water separator to remove rain water form incoming air stream.
- Designed and manufactured in Australia
- 10% higher CFM for this application over other brand snorkels, due to large body design
- Requires cutting and drilling of the fender and A-pillar. Full instructions and template provided.
(20 reviews) -
Firestone
Daystar Universal Airbag Cradle Kit Tacoma and Tundra
- Enjoy full suspension travel and the benefits of air bags with the Daystar Air Bag Cradle Kit
- Fits most full-size trucks and SUVs running 6” diameter bellow-type rear air bags
- Mounts to your truck’s lower air bag suspension mounting bracket—Installation Instructions (PDF)
- Allows full factory differential drop without fear of bag damage
- Provides room for air bags to safely cycle with no loss of wheel travel
- Crafted from super-tough Daystar polyurethane
- Kit includes two cradles and mounting hardware
- Proudly built in the USA
- Your Daystar Air Bag Cradle Kit is backed by a Lifetime Warranty
- Daystar cradle mounts to top of leaf spring, airbag mounts to frame above only
(5 reviews) -
Dobinsons
Dobinsons C45-423 Rear Coil Springs for Pathfinder R52 & R53 – Pair
- These are for the independent rear suspension Pathfinder R52 models 2013-2020 and R53 2021+
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- Sold in Pairs
- Photo is not of actual coil springs for this vehicle
- C45-423 Rear coils will lift 30mm over original height with the added weight of 300-500LBS of constant weight, (for example, towing a heavy trailer)
(3 reviews) -
80 Series Land Cruiser (1990-1997)
Dobinsons C59-313 Rear Coil Springs | Land Cruiser 80 Series – Pair
- Suits Land Cruiser 80 Series and Lexus LX450
- C59-313 4″ lift with 400-750lbs of constant weight
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- 545/555mm free height, 21mm wire, 318LBF/in rate
- Sold in Pairs
(18 reviews) -
SPCFREE SHIPPING
within 48 US StatesTax Return Sale, 10% off
Use Coupon TAXTIMESPC 25465 | UCA’s for Land Cruiser 200 Series & LX570 2008-2021 Pair
- Suits all Toyota Land Cruiser 200 Series and Lexus LX570 models – 2008-2021
- Improved clearance to get around the spring bucket
- 80° of articulation in its ball joint
- SPC’s arm gives you maximum droop travel.
- SPC’s arms have +1° of caster built into them
- Arm will get you 0° to +4° of caster and ±2° of camber
- Maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming
- Installation Instructions
- We offer replacement ball joints as well
(10 reviews) -
SPCFREE SHIPPING
within 48 US StatesTax Return Sale, 10% off
Use Coupon TAXTIMESPC 25455 | UCA’s for Land Cruiser 100 Series & LX470 Pair 1998-2007
- Suits 1998-2007 Toyota Landcruiser 100 Series and 1998-2007 Lexus LX470
- Compatible with or without AHC
- Improved clearance to get around the spring bucket
- 80° of articulation in its ball joint
- SPC’s arm gives you maximum droop travel.
- SPC’s arms have +1° of caster built into them
- Arm will get you 0° to +4° of caster and ±2° of camber
- Maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming
- Installation Instructions
- We offer replacement ball joints as well
(13 reviews) -
Dirt King FabricationFREE SHIPPING
within 48 US StatesDirt King Toyota Tacoma Tubular Ball Joint UCA’s Pair for 2005-2023
- Suits 2005-2023 model Toyota Tacoma 2nd and 3rd Gens – 6 Lug models only
- CAD designed
- Formed steel bushing gussets
- Constructed with 4130 chromoly tubing
- Preassembled with heavy duty Moog ball joints for fast installation
- Probearing Pro 2 Series bushings (new for 2024)
- Maintenance Free Bushings
- Zinc plated components for corrosion resistance
- Professionally MIG welded
- Powder coated black
- Includes Ball Joint Caps
- Installation Instructions
- Proudly made in the USA
(4 reviews) -
DobinsonsFREE SHIPPING
within 48 US StatesDobinsons 12V Zenith 6.0 CFM Air Compressor Kit High Output
- 170L/ minute Air Flow
- Integrated Air Tank
- 2 x 1/8” NPT Auxiliary fittings
- Carry Bag
- 6.5 m Rubber Hose
- Pressure Cut Off Switch
- Safety Release Valve
- Removable Base for Permanent Mounting
- Quick Release Tyre Chuck
(17 reviews) -
40 Series Land Cruiser Early (1960-1979)
Dobinsons 1.75″ Suspension Kit | Toyota Land Cruiser FJ40 BJ40 1960-1979
- Suits Land Cruiser 40 series 1960 to 1979 models with 25mm eye leaf springs
- Choose from Twin Tube Nitrogas shocks or IMS Monotube shocks down below
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Design features include Drawn, tapered and thinned leaf ends
- Front and rear leaf springs have a military wrap on the fixed end of each spring
- Manufactured to international quality standards ISO9001:2008 using premium grade Sup 9 silicon manganese spring steel,
- Anti-Friction inter leaf liners are use to reduce the friction at each leaf end where the load is creates and provides a smoother, quieter ride.
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- Photos are for illustration purposes
(9 reviews) -
GX470 (2002-2009)FREE SHIPPING
within 48 US StatesDobinsons GX470 Snorkel Kit for Lexus 2003-2009
- Lexus GX470 Snorkel Kit – Suits 2003-2009 Models
- Rotationally molded using precision CNC shaped aluminum dies
- Increases air intake height to allow safer water crossings and reduce dust intake
- Increased air intake height rams cooler, cleaner air into the engine increasing engine performance
- Increased air intake height rams cooler, cleaner air into the engine increasing engine performance
- Manufactured from high quality UV resistant LLDPE
- Snorkel Kits include template and all mounting hardware
(8 reviews) -
Tundra 1st Gen (2000-2006)FREE SHIPPING
within 48 US StatesPerformance Rear Brake Line for Tundra 99-06 (BLACK)
- American made D.O.T. Certified extruded teflon core, stainless steel braided and coated with a PVC cover
- Increase your brake pedal feel with stainless brake lines to replace the factory rubber brake lines
- Works with 0-2″ of lift, 21.5″ long
- Suits the following vehicle: Toyota Tundra 1999-2006
- Sold as 1 piece with new retaining clip
- Photo for illustration purposes only
- This item is BLACK in color
(26 reviews)
