Your cart is currently empty!
All Pro Offroad
Showing 31–58 of 58 results
-
All Pro OffroadShips FREE !!
within 48 US StatesAll Pro Complete CV Boot Kit | Toyota Tacoma 1995-2004
- Complete CV boot replacement kit – Suits 1995-2004 Toyota Tacoma 4×4 trucks
- Includes inner and outer CV boots and all related clamps.
- Qty 2 – Long Travel Neoprene Outer CV Boots (can be used on regular or long travel axles)
- Qty 2 – OEM-Style Neoprene Inner CV Boots
- Qty 4 – CV Grease Packets
- Qty 8 – Ear-Type CV-Joint Clamps
- Qty 2 – Axle C-Clips and Snap Rings
- Qty 1 – CV Clamp Crimp Pliers
$160.00 Add to cart -
Leaf Springs - Tacoma 3rd GenShips FREE !!
within 48 US StatesAll Pro 2005-2023 3.0″ Tacoma Leaf Springs – Expedition 500LBS
- Suits 2005-2023 Toyota Tacoma 4×4 Models
- Expedition Leaf Springs give 3.0″ of lift with 500LBS of added constant load, less lift with more weight
- Number of Leaves: 9 + 1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 54-3/8″ (1381 mm)
- Spring Rate: 207 lbs/in
- A higher number of thinner leafs provides a smoother, progressive spring rate compared to fewer, thicker leaves.
- Number of Leaves: 9 + 1 Overload/Rebound
- Double “military” wrap provides extra strength for the main leaf
- Eyelet-to-Eyelet Length (Free): 54-3/8″ (1381 mm)
- “Torque Leaf”, an extra half-leaf at the top of the spring pack, increases anti-wrap properties without hindering travel or ride quality.
- Diamond-cut leaf ends to eliminate stress points which may weaken leafs and lead to premature failure
- Teflon anti-friction pads between leafs provide smoother flex, lessen spring wear and reduce noise
- Leafs are shot-peened after forming to relieve stress.
- Every completed spring pack is pre-cycled to their travel extremity for quality control and to reduce the likelihood of initial sag.
- All-Pro leaf springs are sold in pairs, with a complete urethane bushing and sleeve kit.
- Spring Rate: 151 lbs/in for Standard, 207 lbs/in for Expedition, and 248 lbs/in for Expedition 2.0 Leaf Springs
- After installation, the stock rear bumps will no longer be sufficient to prevent the spring from inverting. You must purchase and install a set of bump stops that are of sufficient height to prevent the spring from going negative arch. For best results, we recommend Wheeler’s SuperBumps (sold separately). WOR-306957
- 4″ Extended brake lines – recommended at this lift height
- Requires a suitable 3″ lift shocks to go with them, such as IMS59-50941 or MRA59-A941
- Sold in Pairs
- Made in USA
$979.00 Add to cart -
Front BumpersShips FREE !!
within 48 US StatesAll Pro 2014-2024 4Runner LoPro Bumper – Bare
- Suits 2014-2024 5th Gen Toyota 4Runners, but not Limited Models
- BUILT 100% IN THE USA!!
- Bare Steel – you have to powder coat or paint it after you receive it
- Photos show after it has been powder coated
- 3/16″ steel faceplate and 1/4″ steel winch plate
- 4 1/2″ x 10″ winch mounting pattern
- Compatible with most 8-12k winches with remote mount solenoid box
- Zinc plated hardware
- Designed to fit 30″ single-row light bars
- Compatible with Toyota Safety Sense (TSS) and Multi-Terrain Monitoring system (MTM)
- Cutting the plastic bumper is required to install this product
- Weighs 74lbs
- NOTE: Not compatible with Limited Edition 4Runners
- Download Instructions
- **We are not able to ship this outside the 48 US States
- Also available powder coated before it ships
$749.00 Add to cart -
Front BumpersShips FREE !!
within 48 US States2016-23 Tacoma Aluminum Low Profile Front Bumper – Center Hoop
- Suits 2016-2023 Toyota Tacoma
- Ships in bare aluminum. You powder coat or paint it after you receive it
- This design allows you to keep the look of the OEM bumper while adding new high-quality features
- This bumper provides an increased approach angle in the front
- The body of this bumper is made from Aluminum with a steel support structure to ensure the highest durability
- We include two 3/4″ thick recovery points that are directly tied to the steel mounting plate
- It is designed to fit 30″ single-row light bars with a mounting width of 31.75″ or less
- This bumper is also compatible with most 8-12k winches with a remote mount solenoid box
- Made in the USA
- Installation Instructions
- Also available without a center hoop
$879.00 Add to cart -
Front BumpersShips FREE !!
within 48 US States2016-23 Tacoma Aluminum Low Profile Front Bumper – No Hoop
- Suits 2016-2023 Toyota Tacoma
- Ships in bare aluminum. You powder coat or paint it after you receive it
- This design allows you to keep the look of the OEM bumper while adding new high-quality features
- This bumper provides an increased approach angle in the front
- The body of this bumper is made from Aluminum with a steel support structure to ensure the highest durability
- We include two 3/4″ thick recovery points that are directly tied to the steel mounting plate
- It is designed to fit 30″ single-row light bars with a mounting width of 31.75″ or less
- This bumper is also compatible with most 8-12k winches with a remote mount solenoid box
- Made in the USA
- Installation Instructions
- Also available with a center hoop attached
$849.00 Add to cart -
Front BumpersShips FREE !!
within 48 US States2016-23 Tacoma Steel Low Profile Front Bumper – Center Hoop
- Suits 2016-2023 Toyota Tacoma
- Ships in bare steel. You powder coat or paint it after you receive it
- This design allows you to keep the look of the OEM bumper while adding new high-quality features
- This bumper provides an increased approach angle in the front
- Made from a CNC laser cut, brake-formed, 3/16″ steel faceplate and the 1/4″ steel winch plate
- We include two 3/4″ thick recovery points that are directly tied to the steel mounting plate
- It is designed to fit 30″ single-row light bars with a mounting width of 31.75″ or less
- This bumper is also compatible with most 8-12k winches with a remote mount solenoid box
- Made in the USA
- Installation Instructions
- Also available without the center hoop attached
$779.00 Add to cart -
Front BumpersShips FREE !!
within 48 US States2016-23 Tacoma Steel Low Profile Front Bumper – No Hoop
- Suits 2016-2023 Toyota Tacoma
- Ships in bare steel. You powder coat or paint it after you receive it
- This design allows you to keep the look of the OEM bumper while adding new high-quality features
- This bumper provides an increased approach angle in the front
- Made from a CNC laser cut, brake-formed, 3/16″ steel faceplate and the 1/4″ steel winch plate
- We include two 3/4″ thick recovery points that are directly tied to the steel mounting plate
- It is designed to fit 30″ single-row light bars with a mounting width of 31.75″ or less
- This bumper is also compatible with most 8-12k winches with a remote mount solenoid box
- Made in the USA
- Installation Instructions
- Also available with a center hoop attached
$749.00 Add to cart -
Tundra 2nd Gen (2007-2021)Ships FREE !!
within 48 US States3/4″ Lift Shackles for Toyota Tundra 2007-2021
- Easily adds 3/4″ of lift to your 2007-2021 Toyota Tundra
- 3/8″ Thick ASTM A36 Steel
- Shackle plates are powder coated black
- Class 10.9 zinc-plated hardware
- Bolts on the same way the factory shackle comes off
- Made in the USA
$130.00 Add to cart