Continue shopping “Warn 103252 VR Evo 10 Winch 10K | Steel Cable” has been added to your cart.
You may be interested in…
-
Gladiator JT 2020-2024+10% Off For Memorial Day!!
Use coupon code MEMORIALDAYJeep Gladiator Long Range Auxiliary Fuel Tank (17gal) 2020+ 3.6L V6
- Suits Jeep Gladiator JT Trucks from 2020 onwards with the 3.6L V6 Gas engine
- Not suitable for Diesel versions
- This is an additional tank that fits on the left side of the driveshaft, it holds 17 gallons, and uses a transfer pump to fill your main tank when you hit a switch
- 17 gallon capacity, fits on opposite side of OE gas tank for maximum clearance!!
- 17 gallons plus your original 22 gallon tank gives you a capacity of 39 gallons in total!!
- Tank fills using the OEM gas door and supplied parts
- Tank uses a transfer pump to fill the main tank, 2L per minute pump rate
- Exhaust modification required – exhaust needs to be replaced with aftermarket/custom or available LRA replacement exhaust kit listed below (tank goes where OE exhaust was routed). Exhaust kit components
- Fitting time – approximately 5.5 hours
- Part Number JGJTPA
- Fitting Instructions – Intended to be installed by a certified mechanic
- This item ships on a pallet to the nearest Truck Freight terminal for you to pickup. We will be in touch with you regarding the nearest freight terminal, unless you add home delivery fee below.
- This product can not be sold or shipped to residents in California, as it will not pass SMOG. Do not order this product if you live in California!!
- MADE IN AUSTRALIA
$2,245.00 Select options -
Upper Control Arms
Pair of UCA Pivot Bolts and Nuts | Toyota and Lexus
- This is a pair of factory size upper control arm pivot bolts and nuts replacements to service two control arms
- Commonly referred to “as the long UCA bolt”
- Services both control arms at once
- Does not come with any washers. New aftermarket UCA’s usually come with the necessary washers
- Vehicle Fitment
-
- 2003-2009 Toyota 4Runner
- 2010-2024 Toyota 4Runner
- 2005-2015 Toyota Tacoma
- 2016-2023 Toyota Tacoma
- 2006+ FJ Cruiser (all years)
- 2003-2009 Lexus GX470
- 2010-2023 Lexus GX460
- Toyota Hilux Vigo
- Toyota Hilux Revo
- Toyota Fortuner
- Toyota Prado 120
- Toyota Prado 150
- Bolt Grade: 10.9
- Head Drive Type: Hex
- Length: 351 mm
- Material: Steel
- SAE or Metric: Metric
- Thread Diameter: 14 mm
- Thread Length: 28.7 mm
- Thread Size: 14 mm
- Thread Type: Fine
$69.00 Add to cart -
Recovery
MAXTRAX MKII Mounting Pins (17mm bolts)
- Sold in a set of four, enough to mount one or two sets of MAXTRAX (two or four boards total).
- 17mm bolt length, see attached photo for description
- 40mm and 17mm refers to the length of bolt used to mount the pins- both the 40mm and 17mm pins will hold either one or two sets of MAXTRAX.
- Designed to mount to your MAXTRAX to wherever you can mount these pins on your vehicle
- M10 stainless bolt has a provision for a small padlock
- Please Note: Antiseize recommended on install
- SOLD AS A SET OF FOUR
$65.99 Add to cart -
WinchesShips FREE !!
within 48 US StatesWarn 103253 VR Evo 10-S Winch 10K | Synthetic Rope
- Winch; VR10-S; Vehicle Mounted; Vehicle Recovery Winch; 12 Volt Electric; 10000 Pound Line Pull Capacity; 90 Foot Synthetic Rope; Hawse Fairlead; Wired Remote; Planetary Gear Drive
- Black Tactical Look Puts You At The Head Of The Off-Road Pack
- Waterproof Albright® Contactor Control For The Ultimate In Reliability
- One-Piece Tie Plate Replaces Tie Rods For Added Strength And Rigidity
- Convertible Control Pack Allows Upright Or Low-Profile Winch Mounting
- Powerful, Efficient Series-Wound Motor
- Best-In-Class Load-Holding Cone Brake For Superior Control
- Limited 7 Year Warranty
-
Winch Rating: 10000 Pound
- Recommended Use: Jeep/Truck/SUV
- Operation Type: Electric
- Mount Type: Fixed Mount
- Voltage: 12 Volt
- Free Spooling: Yes
- Line Length (FT): 90 Feet
- Line Material: Synthetic
- Mounting Pattern Size: 10 Inch Length X 4-1/2 Inch Width
- Brake Type: Spring Applied Disc
- Max Amp Draw: 358 Amp Draw At 1000 Pound
- Gear Reduction Ratio: 218:1
- Includes Mounting Hardware: Yes
- Thermal Shutoff: No
- Color: Black
- Fairlead Type: Hawse
- Remote Type: Wired
- Line Speed At Max Pull: 5.2 Feet Per Minute At 1000 Pound
- Electrical Control Type: Contactors
- Motor Type: Series Wound
- Drive Gear Type: Planetary
- Line Diameter (IN): 3/8 Inch
- Mounting Hole Quantity: 4
- Drum Material: Steel
- Estimated Install Time (Hours): 2
- Warn Warranty information is all listed here: https://www.warn.com/warranties
$864.99 Add to cart -
Fox
Fox Preload Spanner Wrench for 2.5″ Coilovers
- Spanner Wrench
- For 2.5 Coil Overs
- Anodized laser etched billet aluminum
- Pre-Load Adjustment
$61.99 Add to cart -
Sale!ExceptionsShips FREE !!
within 48 US StatesWarn 106688 Diamond Cutter Wheel – 17×8.5″ 5×5″ 0 Offset – Gun Metal
- Warn wheels made specifically for Jeep Wrangler JL, JK, and Gladiator JT.
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 5 lugs, Uses OEM Jeep lug nuts
- Sold Individually
- Gun Metal Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- When Installing On A 2020+ Jeep Wrangler The OEM TPMS Sensor Can Be Used But Must Be Turned In The “UP” Position And It Will Not Lay Flat Against The Wheel
- Bolt Pattern Inch: 5×5.00
- Bolt Pattern Millimeter: Not Applicable
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Gun Metal
- Bolt Pattern Inch: 5×5.00
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 5×127
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 71.50
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: 5 Spoke
- With Inserts: No
- Load Capacity: 2100
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: No
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Sale!SaleShips FREE !!
within 48 US StatesIcon Tubular Lower Trailing Arm Kit | 4Runner FJ Cruiser GX470 GX460 LC200
- Suits 2003-2009 4Runner, 2010-2024 4Runner, FJ Cruiser (all years), Lexus GX470 and Lexus GX460, Lexus LX570 and 200 Series 2008-2021
- CNC machined & notched 1026 DOM steel construction
- Multi durometer bushing for noise free operation and maximum angularity
- No grease required for life of bushings
- Quality JM16T PTFE-lined FK Rod Ends
- Adjustable for various lift heights & driveline angles
- Offset lower link front pivots improve roll steer
- Tangent lower link barrel design reduces risk of off-road hangups
- Integrated OEM emergency brake bracket mount
- ICON1K tested in extreme off-road conditions
- Fabricated components covered under ICON’s lifetime warranty
- Sold as a Pair
- Installation Guide
- Warranty Info
Original price was: $577.45.$549.95Current price is: $549.95. Add to cart -
Ranger 2019+ (US Spec)
Dobinsons Rear Greasable Poly Bush Kit | Ford Ranger 2019-2023
- Suits Ford Ranger 2019-2023
- For any lift height, or no lift. These are OE replacement bushings
- Use with Dobinsons Leaf Springs or any other brand that can accept OE-size bushings
- Pressing of OE bushings may be necessary during removal and installation
- Replaces OE bushings in all 6 positions of rear leaf springs
- Photo for illustration purposes
$115.00 Add to cart -
WinchesShips FREE !!
within 48 US StatesOVS SCAR Waterproof 10K Winch | Synthetic Rope | Wireless Remote
- Single Line Rated Pull: 10,000lb
- Motor: 7.0hp Series Wound
- Waterproof: IP68 Rated
- Voltage: 12V
- Control: Wireless Remote w. 11.5’ Lead with Built in Lithium Battery
- Gear Train: 3 Stage Planetary Gear Systems with Ring Gear
- Gear Ratio: 181:1
- DB Output: Low (it’s quiet)
- Clutch: Rotating Ring Gear
- Braking Action: Automatic Out-Of-Drum
- Drum Size: 2.5” x 8.8”
- Mounting Bolt Pattern: 10” x 4.5”
- Overall Dimensions: 21.3” L x 6.3” W x 7.9” H
- Line Speed: 42’ Per Minute
- Steel Cable: 11/32” x 85’
- Hook: Heavy Duty with Clip
- Fairlead: Aluminum Hawse Fairlead
- Electric Cable: 70” x 25 mm2
- Solenoid: 500A (Heavy – Duty)
- Recommended Battery: 650CCA Minimum.
- Weight: 64 lbs
- Warranty: Limited Lifetime Warranty Mechanical,
- 5 Year Electrical
$499.99 Read more -
Tacoma 3rd Gen (2016-2023)Ships FREE !!
within 48 US StatesDirt King Performance Tacoma Lower Control Arms for 2016-2023
- Suits 2016-2023 3rd Gen Toyota Tacoma 2WD / 4WD
- CAD designed
- Formed steel bushing gussets
- Internally ribbed with extrusions for weight reduction
- Preassembled for fast installation
- Grease fitting ports for easy servicing
- Zinc plated components for corrosion resistance
- Bump stop plating
- Limit strap tabbing
- Bypass shock tabbing
- Professionally MIG welded
- Proudly made in the USA
$1,849.00 Add to cart -
Brake Lines
Extended Rear Brake Lines +4″ for Toyota Tacoma 2005-2023 (Red)
- American made D.O.T. Certified extruded teflon core, stainless steel braided and coated with a PVC cover
- 4″ longer than stock for long travel suspension lifts
- Suits the following vehicles: Toyota Tacoma 2005-2015, Toyota Tacoma 2016+
- Can be used with any lift height, however these are extra long for long travel rear shocks
- Sold as a pair with new retaining clips
$95.00 Add to cart -
Recovery
MAXTRAX Flat Rack Mounts with T-Bolts
- Mount up to 4 Maxtrax (2 Pairs) with this kit, includes mounts, hardware and pins for the Maxtrax
- Designed to mount to your MAXTRAX to your vehicles roof platform or roof rack crossbars
- Can securely attach up to four MAXTRAX MKII (MTXMPS17), 4 MAXTRAX XTREME (MTXXMPS17), or a pair of each (MTXMPSX17)
- Provides 180mm of closer adjustment or 180mm of further apart adjustment from the mounting point of the Flat Racks
- Includes the mounting option of 4 x T-Bolts (Suitable for Rola Titan roof platform, roof platforms and roof rack crossbars from most popular Roof Rack Brands)
- SOLD IN PAIRS
$149.99 Add to cart -
100 Series Land Cruiser IFS (1998-2007)Ships FREE !!
within 48 US StatesDobinsons MRA59-A782 3-Way Adjustable MRA Front Shocks | 100 Series (0-2″ Lift)
- 3-way adjustable valving – Adjust high and low speed compression and rebound
- Massive 66mm (2.6″) Outer body with 60mm (2.36″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 60mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 66mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- Includes Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Reservoir mounts to the empty holes forward of the shock on both sides
- Installation Instructions of the MRA Shocks
- Full 2 year limited warranty, no set rebuild time period
$1,350.00 Add to cart -
Upper Control ArmsShips FREE !!
within 48 US StatesDobinsons Billet Aluminum UCA’s | Nissan Frontier Xterra Pathfinder
- Super strong billet aluminum front upper control arms (UCA’s) for Nissan D40 and D41 platforms
- Suits 2005-2021 Nissan Frontier, 2022-Present Nissan Frontier, 2005-2015 Nissan Xterra, 2005-2012 Nissan Pathfinder R51
- Complete kit for both left and right hand side
- OE-style sealed ball joints for a maintenance free life
- OE-style high quality rubber bushings for maximum NVH dampening and longevity
- No greasing or maintenance required at all, completely noise-free operation
- Adjustable on-vehicle for quick and easy alignment.
- Adjustable Camber and Caster for perfecting the vehicle’s handling
- O-ring sealed ball joint cap for protection against the elements
- Works for any lift height of 1.5″ or more
- Includes detailed instructions
- We recommend visiting an offroad specific shop for alignment, a regular alignment shop may not be able to adjust and align properly due to the added adjustability these arms offer
$1,195.00 Add to cart -
Steering UpgradesShips FREE !!
within 48 US StatesRusty’s Front Track Bar Mount Brace | JL Wrangler + JT Gladiator
- Fits: 2018-Current Jeep JL Wrangler and 2020-Current Jeep JT Gladiator Models
- This is a brace that supports the mount between the steering box and the track bar bracket
- Constructed of 1/4-inch thick laser-cut steel
- CNC formed for an exact fit
- E-coated in black for durability and looks
- Includes Grade 8 hardware
- INSTALLATION INSTRUCTIONS
- Built in Rainbow City, Alabama, USA
$146.00 Select options -
Fox
Fox Back Up Spanner Wrench for 2.5″ Coilovers
- Spanner Wrench
- For 2.5 Coil Overs
- Anodized laser etched billet aluminum
- Back Up Adjustment (removing preload)
$61.99 Add to cart -
Upper Control ArmsShips FREE !!
within 48 US StatesDobinsons Billet Aluminum Adjustable UCA’s | Toyota Tacoma 2005-23
- Super strong billet aluminum front upper control arms (UCA’s) for Toyota Trucks and SUV’s
- Suits 2005-2023 Toyota Tacoma, 2005+ Toyota Hilux, 2005+ Toyota Fortuner
- Complete kit for both left and right hand side
- OE-style sealed ball joints for a maintenance free life
- OE-style high quality rubber bushings for maximum NVH dampening and longevity
- No greasing or maintenance required at all, completely noise-free operation
- Adjustable on-vehicle for quick and easy alignment.
- Adjustable Camber and Caster for perfecting the vehicle’s handling
- O-ring sealed ball joint cap for protection against the elements
- Works for any lift height of 1.5″ or more
- Installation Instructions
- We recommend visiting an offroad specific shop for alignment, a regular alignment shop may not be able to adjust and align properly due to the added adjustability these arms offer
$1,195.00 Add to cart -
Firestone
Firestone 4108 Coil-Rite Rear Helper Airbags for 2-3″ Lift | 4Runner FJ Cruiser GX470 GX460
- Suits all 3rd/4th/5th Gen 4Runners, FJ Cruiser, GX470, GX460 WITH 2-3″ of Lift
- Substitute Option – Air Lift 60769
- These are longer than the Firestone 4135 for lifted vehicles
- Complete kit – 1 per vehicle
- Inserts inside your rear coil springs to add additional load support
- Manually inflate or deflate the air bags to add or remove support or height
- Perfect for people who tow, or regularly load up fully and need additional height or support
- Route the airlines to your rear bumper or a suitable place to easily add or remove air to the bags
- Fitment Notes: NOTE: Custom modifications may be required for lifted applications to ensure air bags are properly supported. If using on a lifted application, do not follow Firestone bump stop/jounce cut instructions. You will need to determine where to cut based on your lift amount (not cutting off as much depending on lift height)
- Installation Manual, Click Here
$144.12 Add to cart -
100 Series Land Cruiser IFS (1998-2007)
OME Heavy Duty Torsion Bar set for Land Cruiser 100 Series V8
- For V8 Gasoline/Petrol powered Land Cruisers from 1998 to 2007
- Increased spring rate to improve handling and lift front end
- Powder coated black for a long lasting finish
- Replaces OE torsion bars without modification
- Torsion bars must be installed with 2/3 suspension down travel and 1/3 up travel to ensure a good ride
$346.00 Add to cart -
DobinsonsShips FREE !!
within 48 US StatesDobinsons MRA45-A642 3-Way Adjustable Struts Xterra Frontier Pathfinder R51
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- External Remote Oil Reservoir with dual speed compression adjustment
- Single Piece Lower Leg, Natural Rubber Bushings Top and Bottom
- Triple Lip Oil Seal for Superior Lifespan
- Direct Bolt-on, Fully Rebuildable Design
- Pre-Charged with Nitrogen, Ready to be Assembled and Installed
- EDP Surface Protection, 3mm Heavy Duty Wall Thickness
- Includes Universal Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Does not include coil springs or top mounts – sold separately
- Standard coil seat height should be set to 106mm from the center of the lower bushing eye to the bottom of the coil seat
- Due to the Restricted Suspension Geometry, a Maximum of 40mm Lift is Achievable in the Front of this Vehicle.
- 395mm extended, 266mm compressed
- FITTING INSTRUCTIONS
- Instructions on setting coil seat height
$1,280.00 Add to cart -
Sale!WheelsShips FREE !!
within 48 US StatesWarn 104490 Jack Hammer Wheel – 17×8.5″ 6×5.5″ 0 Offset – Gun Metal
- Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 6 lugs, Uses OEM lug nuts
- Sold Individually
- Gun Metal Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: Not Applicable
- Weight: 30 LBS
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Gun Metal
- Bolt Pattern Inch: 6×5.50
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 6×139.7
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 106.10
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: Solid Center
- With Inserts: No
- Load Capacity: 2500
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: Yes
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Skid Plates + Sliders - 5th Gen 4RunnerShips FREE !!
within 48 US StatesAll Pro 5th Gen 4Runner IFS Skid Plate – Bare Steel
- Suits 2010-2024 Toyota 4Runner 5th Gen
- Covers from the front bumper down to the first cross member
- 3/16-inch steel – Bare Steel – needs to be painted before installation
- Optimal balance between strength and weight
- Save yourself from costly underbody repairs with this easy to install 5th Gen 4Runner skid plate
- Skidplate not currently compatible with a diff drop kit – you would have to space it down
- Easy, bolt-on installation using all factory hardware
- Compatible with stock bumpers
- Compatible with All-Pro 2010+ 4Runner Front Bumpers
- Not tested with KDSS Vehicles
- Available in 4 variants – Steel or Aluminum, Bare or Powder Coated
- Installation Instructions
$380.00 Add to cart -
Tacoma 2nd Gen (2005-2015)Ships FREE !!
within 48 US StatesDirt King Performance Tacoma Lower Control Arms for 2005-2015
- Suits 2005-2015 2nd Gen Toyota Tacoma 2WD / 4WD
- CAD designed
- Formed steel bushing gussets
- Internally ribbed with extrusions for weight reduction
- Preassembled for fast installation
- Grease fitting ports for easy servicing
- Zinc plated components for corrosion resistance
- Bump stop plating
- Limit strap tabbing
- Bypass shock tabbing
- Professionally MIG welded
- Proudly made in the USA
$1,849.00 Add to cart -
Dobinsons
Dobinsons SC59-002 Pair of Strut Top Plates | Tacoma 98-04 + 4Runner 96-02
- Suits Toyota Tacoma 1st Gen 1998-2004, 4Runner 3rd Gen 1996 to 2002, and Toyota Land Cruiser Prado 90
- Designed to exact OE specs, using all new rubber bushes, washers and seats
- New zinc coated hardware for corrosion resistance
- Allows faster assembly of new components, not needing to disassemble used parts
- Enough for 1 vehicle, sold as pairs
- Photo is of actual product and parts included
- Nut size – M10 x 1.25 nylock – easy to find locally to you if you lose or damage one
- Assembly Instructions
$120.00 Add to cart -
ExceptionsShips FREE !!
within 48 US StatesBack in Stock Now!!Dobinsons IMS59-50220 Front IMS Struts | 05-23 Tacoma GX470 03-09 4Runner 06-09 FJ Cruiser
- Fully rebuildable and re-valvable
- Extended Travel – 567mm extended, 417mm compressed
- SOLD IN PAIRS
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
$650.00 Add to cart -
Skid Plates + Sliders - 5th Gen 4RunnerShips FREE !!
within 48 US StatesAll Pro 5th Gen 4Runner IFS Skid Plate – Black Coated Steel
- Suits 2010-2024 Toyota 4Runner 5th Gen
- Covers from the front bumper down to the first cross member
- 3/16-inch steel – Black Powder Coat
- Optimal balance between strength and weight
- Save yourself from costly underbody repairs with this easy to install 5th Gen 4Runner skid plate
- Skidplate not currently compatible with a diff drop kit – you would have to space it down
- Easy, bolt-on installation using all factory hardware
- Compatible with stock bumpers
- Compatible with All-Pro 2010+ 4Runner Front Bumpers
- Not tested with KDSS Vehicles
- Available in 4 variants – Steel or Aluminum, Bare or Powder Coated
- Installation Instructions
$440.00 Add to cart -
GX460 (2010-2023)
Dobinsons 1.5-3.5″ Lift Kit for Lexus GX460 2010 to 2023 (all options)
- Every suspension option from Dobinsons to lift your Lexus GX460 all on one page
- Here you can lift from a low height up to the maximum bolt-on lift height by making your selections below
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base Kit Includes 2 Front Twin Tube Struts, 2 Rear Twin Tube Shocks, and 4 Coil Springs
- You can choose to upgrade to the higher end IMS or MRA struts and shocks on this page in the drop down menus
From $1,200.00 Select options -
RecoveryShips FREE !!
within 48 US StatesDobinsons 12V Electric Winch – 12000 LBS with Synthetic Rope
- 12,000 Capacity
- 6.5HP Series Wound Motor
- 216:1 Gear Reduction
- 57 LBS Weight
- 10×4.5″ Mounting Pattern
- 6.3 x 8.3 x 21.5″ Overall Dimensions
- 64 x 224mm Drum, Automatic Braking Action
- 3 Stage Planetary Gears
- Plug in Control Range of 10 FT
- Includes Various Control Box Mounting Brackets: Control Box to Cross Rods, Motor Housing & Flat Surface/Bumper Tops
- Sealed Solenoid Box, More Powerful
- Easy Quick Flop Clutch
- Improved Casings
- Motor Housing Breather
- Includes 100FT Synthetic Rope with Hook, Aluminum Hawse Fairlead, Hand Held Control and Wireless Remote (30ft Range)
$1,245.00 Add to cart -
Sale!WheelsShips FREE !!
within 48 US StatesWarn 104489 Jack Hammer Wheel – 17×8.5″ 6×5.5″ 0 Offset – Black
- Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 6 lugs, Uses OEM lug nuts
- Sold Individually
- Black Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: Not Applicable
- Weight: 30 LBS
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Black
- Bolt Pattern Inch: 6×5.50
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 6×139.7
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 106.10
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: Solid Center
- With Inserts: No
- Load Capacity: 2500
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: Yes
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Rusty's Off RoadShips FREE !!
within 48 US StatesRusty’s Adjustable Front Track Bar | JL Wrangler + JT Gladiator
- Fits: 2018-Current Jeep JL Wrangler and 2020-Current Jeep JT Gladiator Models with 2-5″ of lift
- The track bar centers the axle left to right on the vehicle, and adding lift causes the vehicle to be offset and not aligned correctly
- Constructed of 1.50″ x .250″ wall DOM tubing
- Has enough adjustment to accommodate a 2″ to 5″ lift
- Black powder coated and come with long-lasting heavy-duty polyurethane bushings on one end and a heim on the other
- Mounts using stock hardware and locations
- Built in Rainbow City, Alabama, USA
$215.00 Add to cart -
TimbrenShips FREE !!
within 48 US StatesTimbren ABSTORSEQ Active Off Road Rear Bump Stops | Toyota and Lexus SUV’s
- Maintain Full Axle Travel
- Smooth Axle Engagement and Disengagement
- Enhance Suspension Performance
- Progressive Spring Rate
- Absorbs Energy and Cushions Road Shocks
- Stronger Than OEM Bumpstops
- Easy Installation
- Satisfaction Guarantee
- Lifetime Warranty
- Suits 4th and 5th Gen 4Runner (2003-2024), FJ Cruiser, Lexus GX470 and GX460, Landcruiser 100 Series
-
Specs:
- 2,000 lb capacity
- 4,800 lb bump load capacity
- Overall kit height = 5”
- Total deflected (compressed) height = 2.75”
- Amount of deflection (compression) = 2.25”
- Click here for instructions
- Installation video from Exit Offroad
- Depending on the overall travel of the suspension you’re running, bump stop extensions may be necessary to prevent shock bottom-outs. Timbren make 2 options, they do not include any longer bolts which may be required
- A25722-90F00 (1/2″ spacer)
- A25723-90AD00 (1″ spacer)
$269.36 Add to cart -
Rusty's Off RoadShips FREE !!
within 48 US StatesRusty’s JL Rocker Armor with Kicker Tube | JL Wrangler 4-DR 2024+
- Fits: 2024 Jeep JL Wrangler 4-Door Models (will not fit pre-2024’s or 2-Doors)
- Constructed of 2″ x 0.188-wall DOM tubing
- Fully welded for exceptional strength
- Built-in step for easing entry as well as enhancing body protection
- Bolts to the frame
- Durable Satin Black powder coated finish
- Installation Instructions
- Removal of factory side steps or rails is required
- Built in Rainbow City, Alabama, USA
$1,327.00 Add to cart -
Ranger 2019+ (US Spec)
Dobinsons SK19-058 Greasable Shackle Kit | Ford Ranger 2019-2023 USA Spec
- Suits Ford Ranger 2019-2023 USA Spec
- Recessed twin hole greasable design
- Reduces friction in bushes, creating a more comfortable ride
- Heavy duty design and provide simple service through external grease nipples
- Sold as a pair to replace the original shackles
- Incredibly tough and durable gold zinc plating
- Photo for illustration purposes
$110.00 Add to cart -
Sale!ExceptionsShips FREE !!
within 48 US StatesWarn 106690 Jack Hammer Wheel – 17×8.5″ 5×5″ 0 Offset – Gun Metal
- Warn wheels made specifically for Jeep Wrangler JL, JK, and Gladiator JT.
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 5 lugs, Uses OEM Jeep lug nuts
- Sold Individually
- Gun Metal Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- When Installing On A 2020+ Jeep Wrangler The OEM TPMS Sensor Can Be Used But Must Be Turned In The “UP” Position And It Will Not Lay Flat Against The Wheel
- Bolt Pattern Inch: 5×5.00
- Bolt Pattern Millimeter: Not Applicable
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Gun Metal
- Bolt Pattern Inch: 5×5.00
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 5×127
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 71.50
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: Solid Center
- With Inserts: No
- Load Capacity: 2100
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: No
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Bump Stops
Wheeler’s Rear Superbumps for 95+ Tacoma and 99-06 Tundra
- Suits the following vehicles: 1995-2023 Tacoma and 1999-2006 Toyota Tundra
- Bolts in easily and quickly to replace the firm factory bump stops
- Includes necessary bump stops (2), goes under the factory u-bolts
- Made of a super durable micro-cellular polyurethane formula
- Provides controlled, progressive and comfortable bottoming response from your front suspension
- Installation Instructions
$221.00 Add to cart -
Skid Plates + Sliders - 5th Gen 4RunnerShips FREE !!
within 48 US StatesAll Pro 5th Gen 4Runner IFS Skid Plate – Aluminum Black
- Suits 2010-2024 Toyota 4Runner 5th Gen
- Covers from the front bumper down to the first cross member
- 1/4-inch thick 5052 Aluminum – Black Powder Coated
- Optimal balance between strength and weight
- At only 22 lbs, it’s half the weight of similar steel undercarriage protection
- Save yourself from costly underbody repairs with this easy to install 5th Gen 4Runner skid plate
- Skidplate not currently compatible with a diff drop kit – you would have to space it down
- Easy, bolt-on installation using all factory hardware
- Compatible with stock bumpers
- Compatible with All-Pro 2010+ 4Runner Front Bumpers
- Not tested with KDSS Vehicles
- Available in 4 variants – Steel or Aluminum, Bare or Powder Coated
- Installation Instructions
$440.00 Add to cart -
Rear BumpersShips FREE !!
within 48 US StatesWarn 102255 Elite Series Rear Tire Carrier for JL Wrangler
- Suits Jeep Wrangler JL 2018-2023 (all models)
- Tire Carrier ONLY
- Requires the Elite Rear Bumper 102190 to run this tire carrier
- Holds Up To A True 40 Inch Tire
- JL Tire Carrier Add On To The Elite Rear Bumper For Jeep JL
- Built To Match Your Exact Requirements
- Easy To Install
- Limited 1 Year Warranty
- THIS IS A SPECIAL ORDER ITEM
- INSTALLATION INSTRUCTIONS
$1,479.99 Add to cart -
GX470 (2002-2009)
Dobinsons 1″ to 3.5″ Lift Kit for Lexus GX470 (All Options)
- Full Dobinsons Complete Suspension kit for Lexus GX470 from 2003 to 2009, with every possible option listed on one page
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base Kit Includes 2 Front Twin Tube Struts, 2 Rear Twin Tube Shocks, and 4 Standard Coil Springs
- Select the type of struts and shocks you want as well as all possible add-ons down below
- Choose from Dobinsons Classic Twin Tube shocks, IMS Monotube, or MRA 3-way adjustable remote resi shocks
- See note below in description about KDSS models
From $1,200.00 Select options -
TimbrenShips FREE !!
within 48 US StatesTimbren ABSTOF Active Off Road Front Bump Stops | Toyota and Lexus
- Suits 2000-2024 Tundra, 2001-2024 Sequoia, 2005-2023 Tacoma, 1990-2024 4Runner, FJ Cruiser, Lexus GX470 and GX460, Landcruiser 100 and 200 Series
- Note: Some 2nd Gen Toyota Sequoia models have 2 sets of front bump stops, so ordering 2 of these kits will be necessary to replace them all. Inspect your vehicle before ordering
- Maintain Full Axle Travel
- Smooth Axle Engagement and Disengagement
- Enhance Suspension Performance
- Progressive Spring Rate
- Absorbs Energy and Cushions Road Shocks
- Stronger Than OEM Bumpstops
- Easy Installation – Installation Video
- Satisfaction Guarantee
- Lifetime Warranty
- Click here for instructions
$269.36 Add to cart -
Front Bumpers
WARN 101330 Elite Series Stubby Front Winch Bumper for JL & JT
- Suits Jeep Wrangler JL 2018-2023 (all models) and Jeep Gladiator JT 2020-2023 (all models)
- This is a winch bumper – it’s highly recommended to only buy it if you plan to put a winch in, otherwise it will look unfinished from up top since there is no cover panel if no winch is installed
- Photos are shown with all added accessories. This is for the base bumper only, no winch or under protection plates are included
- Certified To Withstand An Industry-Leading 12,000 Pounds Of Pulling Force, Without Deformation
- Durable Flat Black Power-Coated Finish With Five-Stage Pretreat Process And Zirconium Nanotechnology, Engineered To Withstand 408 Hours Of Salt Spray Testing
- Winch Positioned To Deliver Maximum Airflow To The Engine Bay
- Stubby Version Allows For Mounting Of Driving Lights Above The Bumper
- Integrated Off-Road Jack Lifting Points And Shackle-Mounting Tabs
- Limited 1 Year Warranty
- Type: 1-Piece
- Tubular: No
- Air Bag Compatible: No
- Finish: Powder Coated
- Color: Black
- Material: Steel
- Drilling Required: No
- Hitch Type: Without Receiver
- Maximum Gross Trailer Weight: Without Receiver
- Maximum Tongue Weight: Without Receiver
- With Grille Guard: No
- With Grille Screen: No
- With Bull Bar: Yes
- With Winch Mount: Yes
- Winch Compatible: Yes
- Tow Hooks: With Tow Hook Mounts
- D-Rings: With D-Rings
- With Light Cutouts: No
- Light Type: No Lights
- With Mounting Hardware: Yes
- With Skid Plate: No
- With Spare Tire Mount: No
- With License Plate Mount: Yes
- With Jacking Points: No
- With CB Antenna Mount: No
- Estimated Install Time (Hours): 2
- Installation Instructions
- Optional Front Skid Plate Can Be Added
$999.99 Add to cart -
Steering UpgradesShips FREE !!
within 48 US StatesRusty’s HD Tie Rod Assembly | JL Wrangler + JT Gladiator
- Fits: 2018-Current Jeep JL Wrangler and 2020-Current Jeep JT Gladiator Models
- A tie rod is the steering component that connects one wheel to the other, and you adjust toe with this
- Massive 1.75″ x 0.250-wall DOM tubing Tie Rod bar
- Adjustable forged ends are threaded for adjustment without removing the tie rod from the vehicle
- HD jam nuts
- Serrated Lock Washers
- The strongest JL/JT Tie Rod you can buy
- Complete assembly from one side to the other, nothing else needed
- INSTALLATION INSTRUCTIONS
- Built in Rainbow City, Alabama, USA
- Also made in an Aluminum version
$427.00 Select options -
Steering UpgradesShips FREE !!
within 48 US StatesRusty’s HD Aluminum Tie Rod Assembly | JL Wrangler + JT Gladiator
- Fits: 2018-Current Jeep JL Wrangler and 2020-Current Jeep JT Gladiator Models
- A tie rod is the steering component that connects one wheel to the other, and you adjust toe with this
- Massive 1.825″ 7075 SOLID Aluminum Tie Rod
- Adjustable forged ends are threaded for adjustment without removing the tie rod from the vehicle
- HD jam nuts
- Serrated Lock Washers
- The strongest JL/JT Tie Rod you can buy
- Complete assembly from one side to the other, nothing else needed
- INSTALLATION INSTRUCTIONS
- Built in Rainbow City, Alabama, USA
- Also made in a steel DOM version
$502.00 Select options -
SuspensionShips FREE !!
within 48 US StatesDobinsons MRA59-A940 3-Way Adjustable MRA Rear Shocks
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you
- 10 Stage High Speed Compression – For aggressive, high speed offroading through ruts and holes
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm (2.2″) O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMITM CNC machined components for precise tolerances
- Parker Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir, Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg, CNC TIG Precision Welded Body End Mounts
- EDP Surface Protection, Direct Bolt-On Design
- Fully Rebuildable Design, Full 2 year limited warranty, no set rebuild time period
- 14.2″ compressed length, 24.2″ extended length
- Installation Instructions
- Works with factory brake line length and OE bump stop length, no extensions required
- Includes reservoir brackets and hardware
- SOLD IN PAIRS
$1,150.00 Add to cart -
Rusty's Off RoadShips FREE !!
within 48 US StatesRusty’s JL Rocker Armor with Kicker Tube | JL Wrangler 4-DR 2018-2023
- Fits: 2018-2023 Jeep JL Wrangler 4-Door Models (will not fit 2024’s or 2-Doors)
- Constructed of 2″ x 0.188-wall DOM tubing
- Fully welded for exceptional strength
- Built-in step for easing entry as well as enhancing body protection
- Bolts to the frame
- Durable Satin Black powder coated finish
- Installation Instructions
- Removal of factory side steps or rails is required
- Built in Rainbow City, Alabama, USA
$1,327.00 Add to cart -
DobinsonsShips FREE !!
within 48 US StatesETA is July 2024Dobinsons MRA59-A222 3-Way Adjustable MRA Front Struts
- Suits 2001-2007 Toyota Sequoia 4×4, 1998-2004 Toyota Tacoma 4×4, 2000-2006 Toyota Tundra 4×4, 1996-2002 Toyota 4Runner 4×4
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- SOLD IN PAIRS
- 458mm extended length, 335mm compressed
- Includes Universal Reservoir Brackets and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Does not include coil springs or top mounts – sold separately
- Instructions for setting coil seat height
$1,280.00 Add to cart -
SuspensionShips FREE !!
within 48 US StatesDobinsons Tubular UCA Kit | Tacoma Hilux Fortuner 2005-23
- Complete assembled kit for both left and right hand side, includes new ball joints, ball joint caps, OE style rubber frame bushings, and washers
- Has 3 degrees of caster built in, no adjustability or settings required
- Made from HSLA (High Strength Low Alloy) Steel, 5mm (0.2″) wall thickness, and powder coated black
- Works for any lift height of 1.5″ or more. Any height less than that, a proper wheel alignment may not be able to be achieved
- Uses replaceable Japanese-made Sankei 555 ball joints, fully sealed for maintenance free life
- Product Video
- Also sold without ball joints
$795.00 Add to cart -
Sale!WheelsShips FREE !!
within 48 US StatesWarn 106687 Diamond Cutter Wheel – 17×8.5″ 5×5 0″ Offset – Black
- Warn wheels made specifically for Jeep Wrangler JL, JK, and Gladiator JT.
- 17×8.5″ wheel with 0 Offset, 4.75″ backspacing, 5 lugs, Uses OEM Jeep lug nuts
- Sold Individually
- Black Finish
- 1 Piece Cast Aluminum Construction
- Compatible With TPMS (Tire Pressure Monitoring System)
- With Warn Logo Center Cap
- Limited Lifetime Structural Warranty
- When Installing On A 2020+ Jeep Wrangler The OEM TPMS Sensor Can Be Used But Must Be Turned In The “UP” Position And It Will Not Lay Flat Against The Wheel
- Bolt Pattern Inch: 5×5.00
- Bolt Pattern Millimeter: Not Applicable
- Diameter: 17
- Width: 8.5
- Offset: 0
- Backspacing: 4.75
- Material: Aluminum
- Finish: Painted
- Color: Black
- Bolt Pattern Inch: 5×5.00
- Bolt Pattern Inch: Not Applicable
- Bolt Pattern Millimeter: 5×127
- Bolt Pattern Millimeter: Not Applicable
- Lug Nut Seat Type: 60 Degree Conical
- Center Cap: See Replacement Items
- Center Bore: 71.50
- Lug Nut Design: Acorn
- Compatible With TPMS (Tire Pressure Monitoring Sys: Yes
- Basic Design: 5 Spoke
- With Inserts: No
- Load Capacity: 2100
- Size: 17×8.5
- Max Tire Diameter: 40
- Center Cap Design: Warn Logo
- Structural Warranty: Lifetime
- Quantity: Single
- Construction: One Piece Cast
- With Hub Centric Ring: No
- Estimated Install Time (Hours): 0.5
- Prop 65 WARNING: This product can expose you to chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- This item is not returnable – any product damage must be reported to the shipping carrier within 48 hours of receipt.
Original price was: $352.93.$299.99Current price is: $299.99. Add to cart -
Tundra 2nd Gen (2007-2021)Ships FREE !!
within 48 US StatesDirt King Performance Tundra Lower Control Arms – Tundra + Sequoia
- Suits 2007-2021 Toyota Tundra 2WD / 4WD and 2008-2022 Toyota Sequoia 2WD / 4WD
- CAD designed
- Formed steel bushing gussets
- Internally ribbed with extrusions for weight reduction
- Preassembled for fast installation
- Grease fitting ports for easy servicing
- Zinc plated components for corrosion resistance
- Bump stop plating
- Limit strap tabbing
- Bypass shock tabbing
- Professionally MIG welded
- Proudly made in the USA
$2,199.00 Add to cart
Cart totals
| Subtotal | $54,216.73 |
|---|---|
| Shipping |
Shipping to FL. |
| Tax | $4,066.35 |
| Total | $60,024.08 |
