Your cart is currently empty!
4Runner
Showing 211–240 of 269 results
-
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD121 Front Air Locker Toyota Lexus 8″ IFS 30 Spline 3.73-
- For Use With Toyota 8″ IFS Clamshell differential with 30 Spline Axles and 3.73 And Down Factory Gears
- Usually all models that came with a manual transmission used 3.73- factory gear ratios, but you must check before ordering
- Factory R&P may use either RD111 or RD121 depending on ratio. All known aftermarket R&P sets suit RD121.
- If you are re-gearing, check with the gear manufacturer for which Air Locker to order
- Full vehicle fitment list is further down in the main description, includes 4Runner, Tacoma, FJ Cruiser, GX470, GX460
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Select options -
4Runner 5th Gen (2010-2024)
Dobinsons 3″ Long Travel 4Runner MRA Suspension Kit for 2010-24
- Suits Toyota 4Runner 5th Gen 4×4 from 2010 to 2024, without KDSS only
- Extended Travel front 3-Way Adjustable Remote Reservoir Struts and Long Travel Rear shocks along with all related components are listed on this page
- Maximize the suspension travel of your Toyota 4Runner for the most flex and travel you can get from bolt-on parts
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Lifting 3″ front and rear maintains factory rake
- Dobinsons have the largest selection of front and rear coils for 4Runners and in multiple colors
- Add up how much accessory weight you have on the front and then the rear, that’s your constant load
- Then choose the lift height from the coils that most closely matches the added weight
- 3-way Adjustable shocks provide maximum adjustability to provide the perfect ride quality for you.
- 10 Stage High Speed Compression – For aggressive, high speed off roading through ruts and holes.
- 20 Stage Low Speed Compression – For creepy crawling and cornering
- 15 Stage Rebound – Control your coils, prevent bucking
- 50mm CNC Machined High Flow Billet Aluminum Race Piston
- 3mm Thick Heavy Duty DOM Seamless 56mm O.D. shock Body Precision Honed to +/- 0.04mm
- Upgraded 3 Stage FKM‐HNBR Sealing System
- TSUGAMI™ CNC machined components for precise tolerances
- Parker™ Braided High Pressure Hoses
- 5140 HV900 Hard Chrome Plated, Heat treated 18mm Micro-Polished high strength Shock Shaft with a minimum tensile strength exceeding 700MPA
- T6 6061 Height Adjustable Spring Seat
- Carbon-Fibre/PTFE/Disulphide composite wear band for the ultimate in low-friction, low‐wear performance
- 60mm Full 6063 aluminum remote reservoir
- Lightweight CNC Machined Low Friction floating piston
- High Quality O.E.M. Grade Natural Rubber Bushings
- Single Piece Lower Leg
- EDP Surface Protection
- Direct Bolt-On Design
- CNC TIG Precision Welded Body End Mounts
- Fully Rebuildable Design
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Option to have the front struts preassembled prior to shipping to make installation easier at home
- You choose what options you want, nothing is provided if it is not listed once you have selected it
- Suspension Installation Video
From $5,917.72 Select options -
4Runner 5th Gen (2010-2024)
Dobinsons 3″ Long Travel 4Runner IMS Suspension Kit for 2010-24
- Suits Toyota 4Runner 5th Gen 4×4 from 2010 to 2024, without KDSS only
- Extended Travel front struts and Long Travel Rear shocks along with all related components are listed on this page
- Maximize the suspension travel of your Toyota 4Runner for the most flex and travel you can get from bolt-on parts
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Lifting 3″ front and rear maintains factory rake
- Dobinsons have the largest selection of front and rear coils for 4Runners and in multiple colors
- Add up how much accessory weight you have on the front and then the rear, that’s your constant load
- Then choose the lift height from the coils that most closely matches the added weight
- Fully rebuildable and re-valvable shocks and struts
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Instructions for setting coil seat height
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Option to have the front struts preassembled prior to shipping to make installation easier at home
- You choose what options you want, nothing is provided if it is not listed once you have selected it
- Suspension Installation Video
From $4,587.72 Select options -
ExceptionsShips FREE !!
within 48 US StatesOVS Portable Camp Shower – 23 QT
- 23 Quart reservoir size
- Manually operated foot pump
- Premium 500D bag construction, super tough
- Extra Large Fill Opening to make it easier to fill up
- Integrated water level window
- Hands-free spray nozzle
- Use for a shower, bathing, dishes, washing your feet, keeping your kids clean, cleaning off gear around camp
$99.99 Add to cart -
RecoveryShips FREE !!
within 48 US StatesBrute Kinetic Recovery Rope 1-1/4″ x 30FT With Storage Bag
- Minimum Breaking strength is 42,000 lbs
- Works with any recovery point
- Measures 1-1/4″ thick x 30′ long
- Includes a free weather-tested and extra large off-roading storage bag
- Protected against the elements with abrasion and UV resistant coating
- Created with secure double braided nylon
- Reduces damaging impact loads on both vehicles
- Can be used in all terrain sand, mud, and snow
- High visibility red loops increases safety and easy handling
Original price was: $179.99.$125.99Current price is: $125.99. Add to cart -
Factor 55
Factor 55 Hitchlink 2.0 for 2″ Receivers
- Hitchlink 2.0, for 2″ receivers
- Slide it into the receiver, secure it with a pin, and you’re ready to pull
- Made from lightweight, super-strong CNCmachined 6000 series aluminum
- Simply slide the shackle mount into receiver opening and secure with hitch pin (not included)
- Machined radius on shackle mount hole for soft shackle compatibility
- Lightweight precision CNC machined 6000 series aluminum
- Weighs only 1.9 pounds. Steel versions weigh up to 8 pounds
- Rated at 9500 pounds
- Ultimate failure at 51,000 pounds
- Fits common ¾ screw pin shackles/D-Rings
- Machined radius on shackle mount hole for soft shackle compatibility
- Anodized or powder coated for oxidation protection
- Overall size- 6.6″ x 2″ x 2″
- Engineered, tested, and made in USA
$83.00 Select options -
4Runner 2nd Gen (1990-1995)
Dobinsons Toyota 4Runner 2.0″ Suspension Kit for 1990-1995
- Suits Toyota 4Runner 1990-1995 USA models with torsion bars up front and coil springs in the rear
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Multiple coil spring options
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals, Fuchs German shock absorber oil, Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- Choose which specific parts you’d like from the menu below
From $1,215.00 Select options -
4Runner 2nd Gen (1990-1995)
Dobinsons Toyota 4Runner 2.0″ IMS Suspension Kit for 1990-1995
- Suits Toyota 4Runner 1990-1995 USA models with torsion bars up front and coil springs in the rear
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- Multiple coil spring options
- Shocks are Fully rebuildable and re-valvable
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- Choose which specific parts you’d like from the menu below
From $1,755.00 Select options -
SuspensionShips FREE !!
within 48 US StatesDobinsons IMS59-50088 Front Shocks for Toyota 4Runner Pickup (1985 to 1995)
- Suits Toyota 4Runner 1st and 2nd Gen, 1985 to 1995 models with torsion bar suspension, and Toyota Hilux/Pickup 1998 to 2004 models with IFS torsion bar suspension
- Fully rebuildable and re-valvable
- SOLD IN PAIRS
- Zero shock fade in all terrains with full load
- Direct, bolt-on replacement for easy fitment
- IFP – Internal Floating Piston, separates oil and nitrogen
- Corrosion resistant (EDP Surface Protection)
- Heavy duty single piece lower leg
- Enormous oil capacity
- Heavy Duty 3 Stage FKM HNBR Sealing System for the ultimate in reliability
- Race inspired hi-flow CNC 6061 Billet alloy piston – for the ultimate in offroad handling
- 56mm/2.2” Bodied Series – 50mm hi-flow CNC 6061 Billet alloy piston – 50mm bore – Vehicle specific fitment
- Full 2 year limited warranty, no set rebuild time period
- 367mm extended, 262mm compressed
- Photo for illustration purposes
$580.00 Add to cart -
ExceptionsShips FREE !!
within 48 US StatesTimbren Bump Stops Front & Rear | 3rd Gen 4Runner
- Suits 1996-2002 Toyota 3rd Gen 4Runner
- Includes both Front and Rear bump stops for the whole vehicle
- Active Off-Road Bumpstops provide off-road enthusiasts greater control over their vehicles’ suspension travel. Using progressive-rate springs means that instead of a hard stop at the end of axle travel the axle energy will be absorbed when bottoming-out producing smooth, predictable, and quiet axle engagement and disengagement.
- Unlike OEM bump stops, Active Off-Road Bumpstops are made from natural rubber. Just like our Timbren SES line, Active Off-Road Bumpstops carry a lifetime warranty and a satisfaction guarantee.
- ABSTOR4R replaces the rear OEM bump stops and ABSTOF replaces the fronts on the 3rd Gen 4Runner. Upgrade to Active Off-road Bumpstops and experience the difference.
- Maintain Full Axle Travel
- Smooth Axle Engagement and Disengagement
- Enhance Suspension Performance
- Progressive Spring Rate
- Absorbs Energy and Cushions Road Shocks
- Stronger Than OEM Bumpstops
- Easy Installation
- Satisfaction Guarantee
- Lifetime Warranty
- Front Instructions and Rear Instructions
$538.72 Add to cart -
Rear Drawers
Dobinsons DW59-036K Wing Side Panel Kit for 4th Gen 4Runner
- Suits Toyota 4Runner 4th Gen 2003-2009
- Complete wing kit for both sides to suit Dobinsons rear drawer systems
- Includes vertical and horizontal pieces, brackets and hardware
- Fills in the side parts left exposed once drawers have been installed, providing a neat finish
- Drawers are sold separately
$260.00 Add to cart -
Bump StopsShips FREE !!
within 48 US StatesDobinsons 2.2″ Hydraulic Bump Stop IFS Weld on Mount Kit
- Kit includes front Weld on Mounts (Pair) and Dobinsons HBS56-009 Pair of Hydro Bump Stops
- Made for IFS (independent front suspension) vehicles to replace the OEM rubber bump stop
- HBS56-009 – 56mm (2.2″) body | 46mm (1.8″) stroke | 188mm (7.4″) extended | 142mm (5.6″) compressed | 105mm (4.0″) thread length
- CNC Machined 50mm Billet Aluminum Piston
- EDP Coated 3mm Thick 56mm Steel Body
- Threaded Body For Height Adjustment
- Supplied with both Interchangeable Super Quiet Rubber Rod End & Hard Nylon
- 30mm Micro Polished Hard Chrome Shaft
- Slow Rebound Valving To Prevent Bucking
- Removable Dust Cover Boot For Stealth Appearance
- Fully Rebuildable & Tunable
- O-Ring Travel Indicator
- Heavy Duty Extreme-Race style Triple Seal Design
- Nitrogen Gas Charged & Tunable (100 to 300 PSI)
- Pre-charged to 150 PSI
- Extra Short Dead Lengths For Compact Fitment
- Universal design threaded weld on bump stop can to hold the 2.2″ body bump stop
- Cans have 3mm walls for increased strength
- Kit is ideal for those who bottom out often in their offroad driving or go really hard at high speeds
- Could suit a wide range of vehicles as listed below, but remember they are universal and will require adaptation to your vehicle and welding
- Custom fitting and welding is required
- Photo attached shows these bump stops installed with the weld-on mounts on a 3rd Gen Tacoma
From $1,090.00 Select options -
Bump Stops
Dobinsons 2.2″ Hydraulic Bump Stop IFS Weld on Mounts
- Universal design threaded weld on bump stop can to hold a 2.2″ body bump stop
- Intended to be used with the Dobinsons HBS59-009 Hydro bumps
- 3mm walls for increased strength
- Sold as a pair
- Ideal for those who bottom out often in their offroad driving or go really hard at high speeds
- Could suit a wide range of vehicles as listed below, but remember they are universal and will require adaptation to your vehicle and welding
- Custom fitting and welding is required
$400.00 Add to cart -
Coil Springs
Dobinsons C59-274 Front Lifted Coil Springs for Toyota 4×4 Trucks and SUV’s
- 3rd Gen 4Runner 4×4 V6 (1996-2002) – Lifts 3/4″ on a stock to medium load front end
- Toyota Tacoma 4×4 V6 1998 to 2004 – Stock height with stock weight (may vary depending on cab and bed configuration)
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- 349mm free height, 586LBF/in spring rate, 17mm wire
- Sold in Pairs
$270.00 Add to cart -
4Runner 3rd Gen (1996-2002)RCI is on Sale For Spring!!
RCI Transfer Case Skid Plate | 1996-2002 4Runner
- Suits 3RD Gen Toyota 4Runner 1996-2002
- Protects third cross-member, transfer-case, and exhaust pipe
- Photos show this skid as well as others installed
- Built with 3/16″ CNC laser cut steel
- Excellent addition or replacement of weak, lightweight OEM skid plate that directly attaches to the transfer-case (this means impact will not disperse, rendering plate useless)
- Reinforced edges between cross-members for maximum strength and rigidity
- Utilizes carriage bolts for mounting, providing a low profile without the worry of damaging hardware
- Smooth, flat surface that easily slides over obstacles
- Black powder coated for rust resistant, durable and high quality finish
- Installs in minutes
- Hardware and installation instructions included
- Direct bolt on addition to existing factory attachment points, no drilling required
- Also works in conjunction with the RCI Engine and Transmission Skid Plates
- Made in the USA.
Original price was: $249.00.$224.10Current price is: $224.10. Add to cart -
4Runner 3rd Gen (1996-2002)RCI is on Sale For Spring!!
RCI Transmission Skid Plate | 96-02 4Runner 95-04 Tacoma
- Suits 3RD Gen 4Runner and 1995-2004 Tacoma V6 and 4×4 Models ONLY
- Protects transmission and second and third cross-members
- Built with laser cut 3/16″ steel
- Excellent addition or replacement of weak, lightweight OEM skid plates (which do not provide ANY coverage of transmission)
- Service openings for maintenance without removal
- Reinforced edges between cross-members for maximum strength and rigidity
- Smooth, flat surface that easily slides over obstacles
- Black powder coated for rust resistant, durable and high quality finish
- Installs in minutes
- All hardware and installation instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- V6 and 4×4 Models ONLY – does not fit 4 cylinder models or 2 wheel drive
- Made in the USA.
Original price was: $249.00.$224.10Current price is: $224.10. Add to cart -
4Runner 3rd Gen (1996-2002)RCI is on Sale For Spring!!
RCI A-Arm Skid Plates | 96-02 4Runner 95-04 Tacoma
- Suits 3RD Gen 4Runner and 1995-2004 Tacoma
- Protects A-arms
- Built of 3/16” CNC laser cut steel
- Smooth, flat surface that easily slides over obstacles
- Black powder coated for rust resistant, durable and high quality finish
- Installs in minutes
- All hardware and installation instructions provided
- Direct bolt on addition to existing factory attachment points, no drilling required
- Not compatible with OEM front skid plate (without cutting OEM plate)
- Sold as a pair
- Made in the USA.
Original price was: $159.00.$143.10Current price is: $143.10. Add to cart -
Bumpers + Roof Racks - 5th Gen 4RunnerRCI is on Sale For Spring!!
RCI 4Runner Pike Front Bumper for 2014-2024 4Runner
- Suits 2014-2024 Toyota 4Runner 5th Gen (won’t fit Limited or TRD Sport Models)
- Seamlessly matches the contours of the truck for a sleek fit and finish
- Features single row light bar compatibility with most 30″ light bars.
- Tall hoop and no hoop are compatible with adaptive cruise control (Low Hoop is not compatible with ACC)
- Built in winch mounting plate is tied directly to the frame of the truck and accommodates up to 10,000lb winches. (Designed for Warn, SuperWinch and many other winch models on the market)
- Fully gusseted frame mounts and sub structure
- Includes additional support brackets tying the bumper mounting surface to the frame and offering support for the plastic bumper once cut
- 3/4″ shackle mounts run through the bumper shell and are welded directly to frame mounts as well as shell.
- Bolt on addition to existing factory attachment points, no drilling or welding but does require trimming of the OEM plastic bumper
- Heavy duty satin black powder coat option with epoxy primer base coat for excellent durability and lasting good looks
- Material: 3/16″ Steel
- Weight: 80lbs No Hoop, 86lbs Low Hoop, 89lbs Tall Hoop
- Built in Loveland, Colorado, USA
- Built to order based on your preferences chosen
Original price was: $615.00.$553.50Current price is: $553.50. Select options -
Excluded
OME Upper Control Arms – 2003+ 4Runner FJ GX470 GX460
- Suits Toyota 4Runner (2003-2024), FJ Cruiser, Lexus GX470 and GX460
- Forged Ball Joint Housing
- Forged Eyelets
- Heavy Duty greasable Ball Joints
- OME Ball joint protective cap
- GIIRO bushings, free pivoting, grease free and maintenance free
- Increased camber and caster for 2in lift
- Mount provision for OE ABS wires
- ARB’s Intergrit powder coat finish
- Boxed in pairs with foam inserts
- Fitting instructions included
- OME Branded outer sleeve
- Tested and passed to meet VSB14 requirements
- 3 Year Manufacturers Warranty
- Made in Vietnam
$606.00 Add to cart -
Front BumpersShips FREE !!
within 48 US StatesAll Pro 2014-2024 4Runner LoPro Bumper – Bare
- Suits 2014-2024 5th Gen Toyota 4Runners, but not Limited Models
- BUILT 100% IN THE USA!!
- Bare Steel – you have to powder coat or paint it after you receive it
- Photos show after it has been powder coated
- 3/16″ steel faceplate and 1/4″ steel winch plate
- 4 1/2″ x 10″ winch mounting pattern
- Compatible with most 8-12k winches with remote mount solenoid box
- Zinc plated hardware
- Designed to fit 30″ single-row light bars
- Compatible with Toyota Safety Sense (TSS) and Multi-Terrain Monitoring system (MTM)
- Cutting the plastic bumper is required to install this product
- Weighs 74lbs
- NOTE: Not compatible with Limited Edition 4Runners
- Download Instructions
- **We are not able to ship this outside the 48 US States
- Also available powder coated before it ships
$749.00 Add to cart -
Wheels
Warn 104484 6 Lug Epic Wheel Hubs Center Cap – Grey
- Suits Warn wheels made specifically for 6 Lug 2021+ Ford Bronco, 2019+ Ford Ranger, FJ Cruiser, 2005-2023 Toyota Tacoma, and 2003-2023 Toyota 4Runner, Lexus GX470 and GX460
- Grey Finish
- Expertly Made From Premium Materials
- Meets The Highest Quality Standards
- ISO 9001: 2015, ISO 14001: 2015 CERTIFIED
- Easy To Install
- Limited 90 Day Supplier Warranty
- Wheel Series Compatibility: Moonsault/ Diamond Cutter And Jack Hammer Series Wheels
- Bolt Pattern (MM): 6×139.7
- Installation Type: Bolt-On
- Style: Closed
- Color: Grey
- Quantity: Single
- Bolt Pattern (IN): 6×5.50
- Material: Plastic
- Estimated Install Time (Hours): 0.25
Original price was: $27.29.$24.00Current price is: $24.00. Add to cart