Your cart is currently empty!
Shop
Showing 1591–1620 of 1657 results
-
Pathfinder R51 (2005-2012)
Dobinsons Lift Kit Builder | Nissan Pathfinder R51 2005-2012 (all options)
- Complete suspension kit for 4×4 Off Road Use, fine tuned to match the vehicle
- See every option from Dobinsons all on one page
- Full strut and shock information can be seen by making a selection, then clicking on the small square that appears to the right of the box
- Coils are specifically suited to the additional accessory load (weight) on the vehicle
- Nitrogen Gas Charged Shocks, Superior Design, thicker walls, longer travel
- High Quality Australian-made coil springs, heat treated, fully scragged, powder coated
- Base kit Includes 2 Front Struts, 2 Rear Shocks, and 4 Coil Springs
- You choose what level of performance you’d like up front, whether it’s the standard twin tube, IMS monotube, or MRA remote reservoir 3-way adjustable struts
From $1,200.00 Select options -
DobinsonsShips FREE !!
within 48 US StatesDobinsons MRA45-A642 3-Way Adjustable Struts Pair | Xterra Frontier Pathfinder R51
- 3-way adjustable valving – adjust high and low speed compression and rebound
- Massive 56mm (2.2″) Outer body with 50mm (1.97″) Bore and Piston
- External Remote Oil Reservoir with dual speed compression adjustment
- Single Piece Lower Leg, Natural Rubber Bushings Top and Bottom
- Triple Lip Oil Seal for Superior Lifespan
- Direct Bolt-on, Fully Rebuildable Design
- Pre-Charged with Nitrogen, Ready to be Assembled and Installed
- EDP Surface Protection, 3mm Heavy Duty Wall Thickness
- Includes Universal Reservoir Bracket and Hardware, Sticker Pack, and Adjuster Wrench
- Full 2 year limited warranty, no set rebuild time period
- Does not include coil springs or top mounts – sold separately
- Standard coil seat height should be set to 106mm from the center of the lower bushing eye to the bottom of the coil seat
- Due to the Restricted Suspension Geometry, a Maximum of 40mm Lift is Achievable in the Front of this Vehicle.
- 395mm extended, 266mm compressed
- FITTING INSTRUCTIONS
- Instructions on setting coil seat height
$1,280.00 Add to cart -
55 Series (1970-80)
Toyota FJ55 Series 1967-1980 Long Range Replacement Fuel Tank (55gal)
- Suits Toyota FJ55 Series Land Cruiser 1967-1980
- This is a replacement tank that replaces your OE fuel tank, it holds 55 gallons instead of the stock 23.8 gallons and fills the same way an OE tank fills
- 55 gallon capacity, replaces the original tank
- Suits gasoline or diesel fuel
- Tank fills using OEM gas door
- No Exhaust modification required
- Fitting time – approximately 3.5 hours
- THIS TANK IS A SPECIAL ORDER – ALLOW APPROX 6 MONTHS TO BRING FROM AUSTRALIA
- Part Number TLC55R
- Fitting Instructions – Intended to be installed by a certified mechanic
- This item ships on a pallet to the nearest Truck Freight terminal for you to pickup. We will be in touch with you regarding the nearest freight terminal, unless you add home delivery.
- Special order tank, once an order has been placed, it cannot be cancelled.
- This product can not be sold or shipped to residents in California. Do not order this product if you live in California!!
- MADE IN AUSTRALIA
$2,145.00 Select options -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD152 Rear Air Locker Toyota 9.5″ 32 Spline
- For Use only with Toyota 9.5″ 12 Bolt 32 spline Rear Axle
- Suits multiple vehicles, the full list is down below
- Will not suit 5.7L Tundra engines, as they use a larger rear differential (RD146)
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.Â
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Add to cart -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD146 Rear Tundra Air Locker 5.7L V8 10.5″
- For Use only with Toyota Tundra 5.7L V8 REAR 2007 to 2021 with 10.5″ 12 Bolt Ring Gear and 36 spline axles
- Will not suit 4.6L or 4.7L engines, as they use a smaller rear differential (RD152)
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.Â
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,263.00 Add to cart -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD193 Rear Air Locker Toyota 8.15″ 12 Bolt
- For Use With Toyota 8.15″ 12 Bolt Shim Adjusted 30 Spline solid axle – used for many years in some rear applications
- Full vehicle fitment list is further down in the main description, includes 5th Gen 4Runner, Lexus GX460, FJ Cruiser – be sure to check the list below before ordering!!
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.Â
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Select options -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD153 Rear Air Locker Toyota 12 Bolt Semi Float
- For Use With Toyota 12 Bolt Semi Float 30 Spline solid axle – used for many years in some rear applications
- Full vehicle fitment list is further down in the main description, includes Landcruiser 40, 42, 45, 47, 55, 60, 62, 70, 73, 74, 75Â Series – be sure to check the list below before ordering!!
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.Â
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Select options -
Differential | DrivetrainShips FREE !!
within 48 US StatesARB RD142 Air Locker Toyota 12 Bolt Full Float
- For Use With Toyota 12 Bolt Full Float 30 Spline solid axle – used for many years in some front and rear applications
- Full vehicle fitment list is further down in the main description, includes Landcruiser 40, 42, 45, 47, 55, 60, 62, 70, 73, 74, 75Â Series – be sure to check the list below before ordering!!
- At the flick of a dash-mounted switch, compressed air is delivered to the seal housing assembly via a nylon air line.
- Instantaneously go from an open differential to a fully locked differential at the flick of a switch for maximum traction
- Requires an Air Compressor for operation, Sold Separately
- Why do they use air? Air is used on every semi truck on the road to reliably operate their brakes through solenoids, and ARB uses the same technology. When installed correctly, it’s ultra-reliable!!
- The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain.Â
- This Air Locker kit includes the full differential, instruction booklet, airline, fittings, switch and cover, and necessary seals. When combined with an Air Compressor and the original differential, you’ll have everything you need as far as parts go.
- Full specification sheet, including all included parts, CLICK HERE
- It’s recommended that a qualified differential mechanic do the installation for proper setup
- Covered by a full manufacturer’s 5 YEAR WARRANTY
$1,091.00 Select options -
ARB
ARB710LB Orange Snatch Strap Recovery 30′ x 3 1/4″ (24000 LB)
- A snatch strap is a Kinetic strap that stores energy to magnify the pulling power during a vehicle recovery
- Min. breaking strength: 12,500kg / 24000lb Specifically designed to stretch under load for maximum performance
- An ARB snatch strap is a very effective method of extracting a bogged or immobilized 4wd when a second vehicle is present
- Length: 9m / 30 feet. Width: 80mm / 3 1/4″Â
- Material: 100 percent nylon, Elasticity: Stretch (genuine) 20 percent. The kinetic energy generated by the elasticity aids with the recovery itself, while at the same time reducing the likelihood of vehicle damage.
- Reinforced Eyes. For vehicle recovery, a snatch strap is more suitable than a tow strap.
- All ARB snatch straps are woven and fabricated to ARB specifications, and tested by a NATA approved laboratory
- Part no. ARB710LB
- Min. breaking strength: 12,500kg/24000lb
- Length: 9m / 30 feet
- Width: 80mm / 3 1/4″
- Elasticity: Stretch (genuine) 20%
- Material: 100% nylon
- Reinforced eyes: yes
- Eye & seam protector sleeves: yes
$96.00 Add to cart -
ARB
ARB705LB Orange Snatch Strap Recovery 30′ x 2 3/8″ (17500 LB)
- A snatch strap is a Kinetic strap that stores energy to magnify the pulling power during a vehicle recovery
- Min. breaking strength: 8,000kg / 17,600 lb Specifically designed to stretch under load for maximum performance
- An ARB snatch strap is a very effective method of extracting a bogged or immobilized 4wd when a second vehicle is present
- Length: 9m / 30 feet. Width: 60mm / 2 1/8″ feet
- Material: 100 percent nylon, Elasticity: Stretch (genuine) 20 percent. The kinetic energy generated by the elasticity aids with the recovery itself, while at the same time reducing the likelihood of vehicle damage.
- Reinforced Eyes. For vehicle recovery, a snatch strap is more suitable than a tow strap.
- All ARB snatch straps are woven and fabricated to ARB specifications, and tested by a NATA approved laboratory
- Part no. ARB705LB
- Min. breaking strength: 8,000kg/17,600lb
- Length: 9m / 30 feet
- Width:Â 60mm / 2 1/8″
- Elasticity: Stretch (genuine) 20%
- Material: 100% nylon
- Reinforced eyes: yes
- Eye & seam protector sleeves: yes
$70.00 Add to cart -
ARB
ARB510 ARB Air Systems E-Z Tire Deflator with Digital Gauge and Pouch
- Easily lower your tire pressure with a clear digital readout, while you prep your vehicle to hit the trails
- Lowering your tire pressure is a MUST when going offroad for increase comfort, better traction, better tire pattern, and higher performance from your vehicle
- Easy-to-read blue backlit display screen, Large LCD digital readout
- Multiple measurements available: 0-14 bar, 0-200 psi, 0-1400 kpa, 0-14 KgF
- Auto switch off, Auto switch on
- 250mm braided line
- High-quality brass components and crimps
- Rubber bump guard to protect against drops
- Screw-on chuck suits all Schrader valves
- Accuracy to +/- 1psi at 15-75psi
- Includes updated larger canvas pouch for storage
$83.00 Add to cart -
Dobinsons
Dobinsons Add-A-Leaf Center Bolt Pin (Single) (10-90)
- Used in place of original leaf bolt when adding a leaf
- Fits Fits L59-121-R R3 ONLY for 2008+ Tundra
- Sold individually
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Requires lifted leaf springs to ensure proper fitment
$5.00 Add to cart -
40 Series Land Cruiser Late (1980-1984)
Dobinsons TOY-036-R Rear Leaf Springs Pair for 80+ FJ40 BJ40 35mm eyes – Heavy Load
- Suits 1980+ FJ40 and BJ40 models with 35mm eyes.
- Gives 45-50mm lift with 300LBS+ of constant rear weight
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Design features include Drawn, tapered and thinned leaf ends
- Manufactured to international quality standards ISO9001:2008 using premium grade Sup 9 silicon manganese spring steel,
- Anti-Friction inter leaf liners are use to reduce the friction at each leaf end where the load is creates and provides a smoother, quieter ride.
- Sold as a pair – bushings, u-bolts and all other parts sold separately
- Photo for illustration purposes only
$430.00 Add to cart -
40 Series Land Cruiser Late (1980-1984)
Dobinsons HJ47-7L-F Front Leaf Springs Pair for 80+ FJ40 BJ40 35mm eyes – Heavy Load
- Suits 1980+ FJ40 and BJ40 models with 35mm eyes.
- Gives 45mm with 300LBS+ constant front end weight
- Made from the highest quality raw materials to give years of life under the harshest conditions
- Over 60 years of leaf spring design and manufacturing
- Design features include Drawn, tapered and thinned leaf ends
- Manufactured to international quality standards ISO9001:2008 using premium grade Sup 9 silicon manganese spring steel,
- Anti-Friction inter leaf liners are use to reduce the friction at each leaf end where the load is creates and provides a smoother, quieter ride.
- Sold as a pair – bushings, u-bolts and all other parts sold separately
- Photo for illustration purposes only
$430.00 Add to cart -
Explorer U502 AWD 2012+
Dobinsons Rear Shocks Pair | Ford Explorer U502 AWD 2012+ 3.5L 3.7L
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals, Fuchs German shock absorber oil, Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- Matched to compliment Dobinsons Complete Suspension Systems
- Sold in Pairs
- Specifications: 640mm extended, 490mm compressed
$350.00 Add to cart -
Explorer U502 AWD 2012+
Dobinsons Front Struts Pair | Ford Explorer U502 AWD 2012+ 3.5L 3.7L
- Nitrogen Gas Charged, low pressure gas, reducing reducing oil aeration (shock fade)
- Superior Design, thicker walls, longer travel
- Japanese NOK Multi-Lip seals, Fuchs German shock absorber oil, Natural Rubber Bushings for reduced noise vibration and flexibility
- Teflon Piston Rings, double Chrome hardened rods, metal shock boot to protect rod from damage
- Matched to compliment Dobinsons Complete Suspension Systems
- Sold in Pairs, one for the left side and one for the right side
- Specifications: 588mm extended, 393mm compressed
$420.00 Add to cart -
SPCShips FREE !!
within 48 US StatesSPC 25670 | UCA’s for Ford Ranger US-Spec 2019-2020
- Suits Ford Ranger US-Spec 2019-2020 with aluminum knuckles
- Improved clearance to get around the spring bucket
- 80° of articulation in its ball joint
- SPC’s arm gives you maximum droop travel.
- Arm will get you -1.0° to +3.00° of caster and ±2° of camber
- Maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming
- Installation Instructions
- NOTE: For Rangers with aluminum knuckles ONLY
$749.95 Add to cart -
Hilux Revo (2016+)Ships FREE !!
within 48 US StatesDobinsons 4×4 Snorkel Kit for Toyota Hilux Revo 2016+ 2.8L TDI Diesel
- Suits the wide body models only!!
- Made for the 2.8L TDI Diesel engine
- Rotationally molded using precision CNC shaped aluminum dies
- Increases air intake height to allow safer water crossings and reduce dust intake
- Increased air intake height rams cooler, cleaner air into the engine increasing engine performance
- Manufactured from high quality UV resistant LLDPE
- Snorkel Kits include template and all mounting hardware
$355.00 Add to cart -
Pro Comp
Pro Comp 65225 2.5″ Leveling Kit – Sequoia and Tundra 2008-2021
- Fits 2007 to 2021 Toyota Tundra
- Fits 2008 to 2022 Toyota Sequoia
- Level Lift Front Strut Spacers
- Includes Diff Drop Kit
- Lift Height: 2.5 Inch
- Max Tire Size: 33 Inch
- Easy to return to stock height
- View/Download Installation Instructions
Original price was: $179.99.$95.00Current price is: $95.00. Add to cart -
Pro Comp
Pro Comp 65175 2.5″ Leveling Kit – Sequoia and Tundra
- Fits 2000 to 2006 Toyota Tundra
- Fits 2001 to 2007 Toyota Sequoia
- Level Lift Front Strut Spacers
- Includes Diff Drop Kit
- Lift Height: 2.5 Inch
- Max Tire Size: 32 Inch
- Easy to return to stock height
- View/Download Installation Instructions
Original price was: $179.99.$95.00Current price is: $95.00. Add to cart -
Air Compressors
ARB CKSA12 High Performance Small 12V Air Compressor
- Designed specifically to run one or two Air Lockers
- Constructed of lightweight, high-strength, engineering-grade materials, including military and aerospace-grade components
- Relocatable, splash-resistant air filter with washable high-flow sintered bronze filter cartridge for cleaner, cooler air supply
- Fully sealed components for moisture and dust protection
- Over-pressure safety valve-equipped
- Pressure switch-controlled air manifold system specially designed for ARB Air Lockers
- Hard-anodized cylinder bore and PTFE-impregnated carbon fiber piston seal for reduced friction and maximum life
- Anti-vibration, sound-deadening, anodized mount dissipates motor heat and allows compressor to be repositioned 180 degrees
- Ball bearing-equipped motor (no bushings) with unique, linear brush, pre-load system for long life, low heat, and quiet operation
- Compressor piston equipped with a German-made, high shock-rated, cylindrical roller bearing
- Motor is internally thermal-protected against extreme temperature damage
- Comprehensive-photo illustrated installation guide
- 12V DC, Draws 5.5 Amps, 0.98 CFM, 100 PSI max
$241.00 Add to cart -
Snorkel
Safari Snorkel SS56HF – Toyota Tundra 2014-2021
- Created to Fit 2014-2021 Toyota Tundra Models
- Safari V-Spec Snorkel
- Relocates Your Engine’s Air Intake Point to a Higher Location
- Crosslinked Polyethylene Construction
- Built to Perform in Extreme Weather Conditions
- Comes With Stainless Steel and Plated Hardware
- Bolt-On Installation; Drilling Is Required
- Supported by a 2-Year Warranty
- Fully Designed and Manufactured in Australia
- Designed and manufactured in Australia
- Requires cutting and drilling of the fender and A-pillar. Full instructions and template provided.
$674.00 Add to cart -
Snorkel
Safari Snorkel SS172HP – Toyota Tacoma 3rd Gen 2016-2023
- Suits Toyota Tacoma 2016-2023 Models – 3rd Gen Tacoma
- Raises air intake to prevent water ingestion, while also allowing vehicles to utilize clean air when driving in dusty conditions
- Vehicle specific design and factory airbox adaption fitment
- Manufactured using durable, UV stable cross linked polyethylene material
- Supplied as a comprehensive kit, including the necessary fasteners and mounting brackets
- Unique air ram design acts as a highly efficient water separator to remove rain water form incoming air stream
- Designed and manufactured in Australia
- 10% higher CFM for this application over other brand snorkels, due to large body design
- Requires cutting and drilling of the fender and A-pillar. Full instructions and template provided
$627.00 Add to cart -
80 Series Land Cruiser (1990-1997)
Dobinsons C59-317 Rear Coil Springs | Land Cruiser 80 Series
- 80 Series – c59-317 6″ lift with stock weight
- Fully Designed, Manufactured, and Finished In Australia
- Ultra modern design technology, Fully Scragged & Load Tested
- State of the Art Heat Treatment, High Intensity Shot Peened
- Formed on Precision Mandrels, Precise End Configurations
- Durable Powder Coat Finish
- 560/570mm free height, 21mm wire, 303LBF/in rate
- Sold in Pairs
$405.00 Add to cart -
Bump Stops
Dobinsons Hydro Bump Weld On Mounting Cans 2.6″ 66mm (Pair)
- Dobinsons threaded weld-on cans (pair) for 2.6″ / 66mm body Hydro Bumps
- Threaded weld can
- Zinc coating for rust prevention (Must be ground off before welding)
- 3mm walls for increased strength
- Sold in Pairs
$150.00 Add to cart -
Bump Stops
Dobinsons Hydro Bump Weld On Mounting Cans 2.2″ 56mm (Pair)
- Dobinsons threaded weld-on cans (pair) for 2.2″ / 56mm body Hydro Bumps
- Threaded weld can
- Zinc coating for rust prevention (Must be ground off before welding)
- 3mm walls for increased strength
- Sold in Pairs
$90.00 Add to cart -
Bump StopsShips FREE !!
within 48 US StatesDobinsons Hydro 2.6″ Bump Stops – 66mm body x 85mm stroke (Pair)
- Dobinsons HBS66-003 – 66mm body x 85mm stroke (Pair) – for 4-6″ lift heights
- CNC Machined 60mm Billet Aluminum Piston
- EDP Coated 3mm Thick 66mm Steel Body
- Threaded Body For Height Adjustment
- Supplied with both Interchangeable Super Quiet Rubber Rod End & Hard Nylon
- 66mm body x 85mm stroke
- 40mm Micro Polished Hard Chrome Shaft
- Slow Rebound Valving To Prevent Bucking
- Removable Dust Cover Boot For Stealth Appearance
- Fully Rebuildable & Tunable
- O-Ring Travel Indicator
- Heavy Duty Extreme-Race style Triple Seal Design
- Nitrogen Gas Charged & Tunable (100 to 300 PSI)
- Pre-charged to 150 PSI
- Extra Short Dead Lengths For Compact Fitment
- No mounting cans or mounting fit kit is included (sold separately)
$820.00 Add to cart -
Bump StopsShips FREE !!
within 48 US StatesDobinsons Hydro 2.6″ Bump Stops – 66mm body x 57mm stroke (Pair)
- HBS66-002 – 66mm body x 57mm stroke (Pair) – for 0-4″ lift heights
- CNC Machined 60mm Billet Aluminum Piston
- EDP Coated 3mm Thick 66mm Steel Body
- Threaded Body For Height Adjustment
- Supplied with both Interchangeable Super Quiet Rubber Rod End & Hard Nylon
- 66mm body x 57mm stroke
- 40mm Micro Polished Hard Chrome Shaft
- Slow Rebound Valving To Prevent Bucking
- Removable Dust Cover Boot For Stealth Appearance
- Fully Rebuildable & Tunable
- O-Ring Travel Indicator
- Heavy Duty Extreme-Race style Triple Seal Design
- Nitrogen Gas Charged & Tunable (100 to 300 PSI)
- Pre-charged to 150 PSI
- Extra Short Dead Lengths For Compact Fitment
- No mounting cans or mounting fit kit is included (sold separately)
$820.00 Add to cart